Tata Steel
Proud winner of ABECA 2024 - AmbitionBox Employee Choice Awards
Filter interviews by
Clear (1)
I applied via Approached by Company and was interviewed in Sep 2022. There were 3 interview rounds.
My job role as a QA QC Engineer has made me technically sound by providing me with in-depth knowledge of mechanical properties of alloys and testing methods.
Regularly conducting tests on various alloys to determine their mechanical properties such as strength, hardness, and ductility
Utilizing testing methods such as tensile testing, hardness testing, impact testing, and metallography to assess the quality of alloys
Anal...
Rate your
company
🤫 100% anonymous
How was your last interview experience?
posted on 5 Feb 2025
posted on 8 Jan 2023
I applied via Company Website
I applied via Company Website and was interviewed before May 2018. There were 2 interview rounds.
Lean and Six Sigma are methodologies used to improve processes and reduce waste.
Lean focuses on eliminating waste and increasing efficiency in processes
Six Sigma focuses on reducing defects and improving quality
Both methodologies use data analysis and continuous improvement to achieve their goals
Example: Lean can be used to streamline a manufacturing process by eliminating unnecessary steps
Example: Six Sigma can be use...
Discussed at infrastructure
posted on 13 Nov 2024
I applied via Walk-in and was interviewed in Oct 2024. There was 1 interview round.
To check the motor, you can perform various tests and inspections to ensure it is functioning properly.
Check for any physical damage or wear on the motor casing
Inspect the wiring connections for any loose or damaged wires
Measure the voltage and current going into the motor to ensure it is within the specified range
Test the motor's insulation resistance to check for any faults
Run the motor under load to see if it operat
Power analysis involves measuring and analyzing the electrical power consumption of a system or device.
Identify the components of the system or device that consume power.
Measure the current and voltage across these components using appropriate instruments.
Calculate the power consumption using the formula P = VI, where P is power, V is voltage, and I is current.
Analyze the power consumption data to identify any ineffici...
A transformer is a device that transfers electrical energy between two or more circuits through electromagnetic induction.
Transformers are used to increase or decrease voltage levels in electrical circuits.
They consist of two coils of wire, known as the primary and secondary coils.
Examples of transformers include power transformers used in electrical substations and voltage transformers in electronic devices.
I applied via JSL's own Job portal. and was interviewed in Apr 2024. There was 1 interview round.
Pipe layout refers to the arrangement and positioning of pipes in a system to ensure efficient flow of fluids or gases.
Pipe layout involves determining the route, size, and elevation of pipes within a system.
Consideration must be given to factors such as pressure drop, flow rate, and accessibility for maintenance.
Proper pipe layout can optimize system performance and minimize potential issues such as leaks or blockages
Position displacement pumps are used for hydraulic systems due to their ability to provide precise control over fluid flow and pressure.
Position displacement pumps offer accurate and repeatable flow rates, making them ideal for applications requiring precise control.
These pumps are capable of maintaining constant pressure, which is crucial in hydraulic systems to ensure consistent performance.
Position displacement pump...
Pipe schedule refers to the wall thickness of pipes used in various industries.
Pipe schedule is a way to standardize the thickness of pipes for different applications.
It is denoted by a number followed by 'S' (e.g. Schedule 40, Schedule 80).
Higher schedule numbers indicate thicker walls for higher pressure applications.
Pipe schedules are important for ensuring compatibility and safety in piping systems.
The procedure for replacing a pump in a hydraulic system involves draining the system, disconnecting the old pump, installing the new pump, and refilling the system.
Drain the hydraulic system to prevent spills and contamination.
Disconnect the old pump from the system by removing any connecting hoses or pipes.
Install the new pump in the same location as the old pump, ensuring proper alignment and connection.
Refill the h...
System pressure in a hydraulic system is set using a pressure relief valve or a pressure regulator.
System pressure can be set using a pressure relief valve which opens to release excess pressure.
A pressure regulator can also be used to control the pressure by adjusting the setting.
The pressure setting is typically determined based on the requirements of the hydraulic system and the components used.
Monitoring devices su...
TIG welding is a welding process that uses a non-consumable tungsten electrode to produce the weld. It is widely used in jointing hydraulic pipes due to its precision and clean welds.
TIG welding stands for Tungsten Inert Gas welding.
It uses a non-consumable tungsten electrode to create the weld.
TIG welding produces high-quality, clean welds with minimal spatter.
The process allows for precise control over the welding ar...
Cleaning pipe lines involves various procedures such as flushing, pigging, and chemical cleaning.
Flushing involves using water or air pressure to remove debris and buildup from the pipes.
Pigging uses a device called a 'pig' to scrape the inside of the pipe and push out any blockages.
Chemical cleaning involves using specific chemicals to dissolve and remove stubborn deposits in the pipes.
Regular maintenance and inspecti...
NAS value is a measure of network-attached storage performance and reliability, important to achieve within standard limits for optimal data storage and access.
NAS value stands for Network-Attached Storage value, which measures the performance and reliability of a storage system.
It is important to achieve NAS value within standard limits to ensure optimal data storage and access speeds.
Exceeding NAS value limits can re...
Conveyor alignment is done by adjusting the idlers and pulleys to ensure the belt runs straight and centered on the conveyor frame.
Check for any misalignment by observing the belt's position on the idlers.
Adjust the idlers and pulleys to ensure the belt runs straight and centered.
Use alignment tools such as laser alignment devices for precision.
Regularly inspect and maintain the conveyor system to prevent misalignment ...
Factors and requirements for procuring a conveyor belt
Consider the type of material being transported
Determine the required capacity and speed of the conveyor belt
Evaluate the environment where the conveyor belt will be used (e.g. temperature, humidity)
Assess the maintenance and operating costs of the conveyor belt
Check the safety features and regulations compliance of the conveyor belt
Look into the reputation and reli...
Couplings are used to connect two shafts together while allowing for some degree of misalignment. Alignment is crucial for proper functioning.
Types of couplings include rigid, flexible, fluid, and magnetic couplings.
Procedure for alignment involves checking shaft alignment using tools like dial indicators, laser alignment systems, or straightedges.
Alignment process includes adjusting shims, moving machinery, and rechec...
A rapid wagon loading system is a technology used to quickly load goods onto train wagons for transportation.
Utilizes automated machinery to load goods efficiently
Reduces loading time significantly compared to manual loading
Commonly used in industries such as mining, agriculture, and logistics
Examples include conveyor belt systems, robotic arms for loading, and automated palletizing systems
posted on 12 Aug 2024
MCC stands for Motor Control Center and PCC stands for Power Control Center. They are electrical panels used to control and distribute power to motors and other electrical equipment.
MCC panels are used to control and distribute power to motors in industrial settings.
PCC panels are used to control and distribute power to various electrical equipment.
Both panels play a crucial role in ensuring efficient and safe operatio...
posted on 2 Sep 2023
based on 2 interviews
Interview experience
Anonymously discuss salaries, work culture, and many more
Get Ambitionbox App
based on 8 reviews
Rating in categories
Manager
1.6k
salaries
| ₹6 L/yr - ₹20.5 L/yr |
Assistant Manager
1.4k
salaries
| ₹5.2 L/yr - ₹15.5 L/yr |
Senior Manager
1.2k
salaries
| ₹9.2 L/yr - ₹35 L/yr |
Junior Engineer
907
salaries
| ₹2 L/yr - ₹10 L/yr |
Associate Engineer
882
salaries
| ₹2 L/yr - ₹7.8 L/yr |
JSW Steel
Steel Authority Of India
Vedanta Limited
ArcelorMittal Nippon Steel