Filter interviews by
I applied via Company Website and was interviewed in Jul 2022. There were 3 interview rounds.
Question based about on heat treatment & annealing process,
Iron-carbide is a compound formed by the combination of iron and carbon.
Iron-carbide is also known as cementite.
It is a hard and brittle compound.
The chemical formula of iron-carbide is Fe3C.
It is a constituent of steel and cast iron.
Iron-carbide has a crystal structure known as orthorhombic.
If the annealing process fails and hardness is not in range, I would analyze the possible causes and take corrective actions.
Analyze the annealing process parameters and compare them with the standard values
Check if the temperature and time of annealing were accurate
Inspect the cooling process to ensure it was done properly
Examine the material composition and its suitability for annealing
Consider re-annealing the mater...
Top trending discussions
I applied via campus placement at Sanjay Gandhi Polytechnic, Bellary and was interviewed in Jun 2021. There was 1 interview round.
I applied via Naukri.com and was interviewed in Nov 2020. There was 1 interview round.
The main role of a Junior Electrical Maintenance Engineer is to assist in the maintenance and repair of electrical systems and equipment.
Assist in the maintenance and repair of electrical systems and equipment
Perform routine inspections and tests on electrical systems and equipment
Troubleshoot and diagnose electrical problems
Assist in the installation of new electrical systems and equipment
Maintain accurate records of ...
Glass wire beaker/conical/bueret/pipete
Acid mixture/BDS indicator/Hgcl2/Sncl2/k2cr2o7/amonia buffer/koh/edta
Sponge iron/iron ore/dolomite/coal
posted on 21 Apr 2022
I applied via Approached by Company and was interviewed in Nov 2022. There were 3 interview rounds.
I applied via Naukri.com and was interviewed in Aug 2021. There were 2 interview rounds.
Otto cycle is used in gasoline engines and Diesel cycle is used in diesel engines.
Otto cycle is a constant volume cycle used in gasoline engines.
Diesel cycle is a constant pressure cycle used in diesel engines.
Otto cycle has a higher compression ratio compared to Diesel cycle.
Otto cycle has a spark plug for ignition while Diesel cycle uses compression ignition.
Both cycles involve four processes: intake, compression, po
Stress is the force applied to a material, while strain is the resulting deformation or change in shape.
Stress is a measure of the internal forces within a material, while strain is the measure of the deformation or change in shape.
Stress is typically measured in units of force per unit area (such as N/m^2 or Pa), while strain is a dimensionless quantity.
Stress can cause a material to deform or break, while strain is t...
There are two main types of Ramming mass: acidic and basic.
Acidic Ramming Mass: used for lining induction furnaces and arc furnaces.
Basic Ramming Mass: used for lining steel ladles and EAF (Electric Arc Furnace).
There are several types of steel, each with different properties and uses. The percentage of steel in a particular alloy can vary.
Types of steel include carbon steel, alloy steel, stainless steel, tool steel, and high-speed steel.
The percentage of steel in an alloy can range from as low as 0.2% to as high as 2.1% depending on the type of steel and its intended use.
For example, carbon steel typically contains around 0.2...
First law states energy cannot be created or destroyed, second law states entropy always increases, third law states entropy approaches zero at absolute zero.
First Law: Energy cannot be created or destroyed, only transferred or converted. Example: A car engine converts fuel into mechanical energy.
Second Law: Entropy of an isolated system always increases over time. Example: Heat always flows from hot to cold objects.
Th...
I applied via Campus Placement and was interviewed in Jan 2022. There were 3 interview rounds.
A circuit breaker is an automatic electrical switch designed to protect an electrical circuit from damage caused by overload or short circuit.
It is a safety device that automatically interrupts the flow of current in a circuit when it exceeds a safe level
It is used to protect electrical equipment from damage due to overcurrent
It can be reset after tripping, unlike a fuse which needs to be replaced
It comes in different ...
DC motors and AC motors are two types of electric motors commonly used in various applications.
DC motors operate using direct current, while AC motors operate using alternating current.
DC motors are typically used in applications that require high torque at low speeds, such as in electric vehicles and robotics.
AC motors are commonly used in household appliances, industrial machinery, and HVAC systems.
DC motors are simp...
The chance of survival depends on various factors such as insulation, grounding, and the strength of the electrical surge.
The chance of survival depends on the insulation of the car, as it acts as a barrier against electrical current.
If the car is properly grounded, it can help dissipate the electrical surge and reduce the risk of injury.
The strength of the electrical surge also plays a crucial role in determining the ...
I applied via Walk-in and was interviewed in Jun 2024. There was 1 interview round.
A single line diagram of a VFD shows the electrical connections and components in a simplified format.
Shows the power supply, VFD unit, motor, and control devices in a single line format
Used for easy understanding of the electrical connections and components
Does not show the physical layout or exact wiring details
posted on 26 Apr 2022
I applied via Campus Placement and was interviewed in Oct 2021. There was 1 interview round.
based on 1 review
Rating in categories
Junior Engineer
40
salaries
| ₹1.8 L/yr - ₹3.6 L/yr |
Production Engineer
22
salaries
| ₹1.8 L/yr - ₹3.7 L/yr |
Engineer
14
salaries
| ₹2.5 L/yr - ₹3.6 L/yr |
Senior Engineer
13
salaries
| ₹3 L/yr - ₹4.8 L/yr |
Quality Engineer
12
salaries
| ₹2.2 L/yr - ₹4.3 L/yr |
Tata Steel
JSW Steel
Steel Authority Of India
Jindal Steel and Power