Junior its Engineer
10+ Junior its Engineer Interview Questions and Answers

Asked in Tata Steel

Q. What is the main role of Junior engineer in Electrical maintenance and How to provide the company facilities to the Junior engineer.
The main role of a Junior Electrical Maintenance Engineer is to assist in the maintenance and repair of electrical systems and equipment.
Assist in the maintenance and repair of electrical systems and equipment
Perform routine inspections and tests on electrical systems and equipment
Troubleshoot and diagnose electrical problems
Assist in the installation of new electrical systems and equipment
Maintain accurate records of maintenance and repair work
Communicate effectively with se...read more

Asked in Shilpa Steel and Power

Q. If the annealing process fails and the hardness is not within the specified range, what steps would you take next?
If the annealing process fails and hardness is not in range, I would analyze the possible causes and take corrective actions.
Analyze the annealing process parameters and compare them with the standard values
Check if the temperature and time of annealing were accurate
Inspect the cooling process to ensure it was done properly
Examine the material composition and its suitability for annealing
Consider re-annealing the material with adjusted parameters
Consult with senior engineers ...read more
Junior its Engineer Interview Questions and Answers for Freshers

Asked in B. G. Shirke Construction Technology

Q. What are the alternative methods for lapping length?
Alternative methods for lapping length include using formulas, empirical methods, and software tools for precise calculations.
Use empirical formulas based on material properties and load conditions.
Consider using software tools like CAD for accurate modeling.
Consult design codes that provide guidelines for lapping lengths.
Utilize finite element analysis (FEA) for complex structures.

Asked in Shilpa Steel and Power

Q. Self introduction, draw the diagram of iron-carbide,
Iron-carbide is a compound formed by the combination of iron and carbon.
Iron-carbide is also known as cementite.
It is a hard and brittle compound.
The chemical formula of iron-carbide is Fe3C.
It is a constituent of steel and cast iron.
Iron-carbide has a crystal structure known as orthorhombic.

Asked in ITS Planners and Engineers

Q. How long will it take you to write code for the Fibonacci series?
The time taken to write code for Fibonacci series depends on the programming language and the approach used.
The recursive approach is simple but can be slow for large inputs.
The iterative approach is more efficient and faster.
Dynamic programming can be used to optimize the recursive approach.
The time complexity of the iterative approach is O(n), while the recursive approach is exponential.
Using memoization can improve the performance of the recursive approach.

Asked in Hyundai Motor India Limited

Q. Car assembly process any spec error and missmatch
The car assembly process involves identifying and rectifying any specification errors and mismatches.
Inspect each component for correct specifications
Ensure proper alignment and fitment of parts
Verify that all electrical and mechanical connections are accurate
Check for any discrepancies in color, texture, or finish
Test functionality of various systems and components
Junior its Engineer Jobs




Asked in Inox Wind

Q. How does a wind turbine generate power?
Wind turbines generate power through the conversion of wind energy into electrical energy.
Wind turbines have large blades that capture the kinetic energy of the wind.
The wind turns the blades, which are connected to a rotor.
The rotor spins a generator, which produces electricity.
The electricity generated is then transmitted through power lines for use.
Wind turbines can generate power even at low wind speeds, but their efficiency increases with higher wind speeds.

Asked in L&T–MHI Power Boilers

Q. How many outer walls need coating?
The number of coating outer side walls depends on the specific engineering project and its requirements.
The number of coating outer side walls varies depending on the type of structure being built.
For example, a building may have one or multiple coating layers on its outer walls.
The number of coating layers may also depend on the climate and environmental factors of the location.
The engineer must determine the appropriate number of coating layers based on the project's specif...read more
Share interview questions and help millions of jobseekers 🌟

Asked in MG Motor

Q. What kind of PLCs are used in TML?
TML uses various PLCs for different applications.
TML uses Siemens PLCs for its engine assembly lines.
Allen Bradley PLCs are used for the body shop and paint shop.
Mitsubishi PLCs are used for the press shop.
TML also uses Schneider Electric PLCs for some of its applications.
Asked in Wavemaker Global

Q. What is the density of water?
The density of water is 1 gram per cubic centimeter at standard temperature and pressure.
The density of water is a physical property that describes the amount of mass per unit volume of water.
It is commonly used in various scientific and engineering calculations.
The density of water varies with temperature and pressure.
At standard temperature and pressure (STP), the density of water is 1 gram per cubic centimeter.
This means that one cubic centimeter of water weighs one gram.

Asked in MG Motor

Q. What is a profile in maintenance?
Profile in maintenance refers to the set of responsibilities and tasks assigned to a maintenance professional.
A profile in maintenance typically includes tasks such as equipment inspections, repairs, and preventative maintenance.
Maintenance professionals may also be responsible for managing inventory and ordering replacement parts.
In some cases, maintenance professionals may also be responsible for training and supervising junior staff members.
Examples of job titles in mainte...read more

Asked in Jai Balaji Group

Q. what is pump and it's type
A pump is a mechanical device used to move fluids from one place to another. There are various types of pumps.
Pumps are used in various industries such as water treatment, oil and gas, and chemical processing.
Types of pumps include centrifugal, positive displacement, and axial flow pumps.
Centrifugal pumps are commonly used in water treatment and HVAC systems.
Positive displacement pumps are used in applications where a constant flow rate is required, such as in chemical proces...read more

Asked in L&T–MHI Power Boilers

Q. Can you describe the drawing?
I'm sorry, I cannot answer this question as there is no drawing provided.

Asked in Infosys

Q. Write a program to check if a given string is a palindrome.
A program to check if a given string is a palindrome or not.
Create a function that takes a string as input
Convert the string to lowercase to ignore case sensitivity
Remove all non-alphanumeric characters from the string
Reverse the string and compare it with the original string
If they are the same, return true, else return false

Asked in Hitachi Hi-Rel Power Electronics

Q. ALL BATTERY TYPE
Different types of batteries used in various applications.
Alkaline batteries: commonly used in household devices like remote controls
Lithium-ion batteries: used in smartphones, laptops, and electric vehicles
Lead-acid batteries: used in cars, motorcycles, and uninterruptible power supplies
Nickel-metal hydride (NiMH) batteries: used in digital cameras and portable electronics
Zinc-carbon batteries: commonly found in flashlights and toys
Interview Experiences of Popular Companies






Calculate your in-hand salary
Confused about how your in-hand salary is calculated? Enter your annual salary (CTC) and get your in-hand salary


Reviews
Interviews
Salaries
Users

