Reliance Industries Site Engineer Interview Questions and Answers

Q1. What is the main components part of cement?
Ans. 
The main components of cement are limestone, clay, and gypsum.
• Limestone: primary raw material used in cement production

• Clay: provides silica, alumina, and iron oxide necessary for cement

• Gypsum: regulates setting time and helps control the rate of hardening
Answered by AI
Add your answer
Q2. What is the maximum percentage (%) of carbon and silicon using in cement?
Ans. 
The maximum percentage of carbon and silicon in cement is typically around 5% and 3% respectively.
• Maximum percentage of carbon in cement is around 5%

• Maximum percentage of silicon in cement is around 3%

• Higher percentages can affect the quality and properties of the cement
Answered by AI
Add your answer

Q1. What is water cement ratio
Ans. 
Water cement ratio is the ratio of the weight of water to the weight of cement used in a concrete mix.
• Water cement ratio is a crucial factor in determining the strength and durability of concrete.

• A lower water cement ratio results in stronger and more durable concrete.

• The ideal water cement ratio varies depending on the type of concrete mix and its intended use.

• For example, a typical water cement ratio for general purp
Answered by AI
Add your answer
Q2. How to observe water test
Ans. 
To observe a water test, ensure proper equipment is used, follow testing procedures accurately, record results, and analyze for any abnormalities.
• Use clean and calibrated equipment for accurate results

• Follow testing procedures as per standard guidelines

• Record all observations and results in a logbook

• Analyze the results for any abnormalities or deviations from expected values
Answered by AI
Add your answer

Q1. Waterproofing knowledge
Add your answer
Q2. How to stop waterproofing condition
Ans. 
To stop waterproofing condition, proper surface preparation, selection of appropriate waterproofing materials, and regular maintenance are essential.
• Ensure proper surface preparation before applying waterproofing materials

• Select appropriate waterproofing materials based on the specific requirements of the project

• Regularly inspect and maintain the waterproofing system to prevent any damage or leaks

• Address any issues or
Answered by AI
Add your answer

Behavioral questions and resume delve

Pmi - product management information

My GD topic was renewable energy.

Q1. Tell me about yourself
Ans. 
I am a Senior Engineer with 10+ years of experience in designing and implementing complex systems.
• 10+ years of experience in engineering

• Specialize in designing and implementing complex systems

• Strong problem-solving skills

• Experience with various programming languages such as Java, Python, and C++
Answered by AI
Add your answer
Q2. Why do you want to leave your previous company and join GAIL
Ans. 
Seeking new challenges and growth opportunities at GAIL.
• Desire for new challenges and opportunities for growth

• Interested in working in a different industry or with different technologies

• Attracted to GAIL's reputation and projects

• Seeking a more collaborative and innovative work environment
Answered by AI
Add your answer
Q3. What do your parents do
Ans. 
My parents are both retired now, but my father used to work as a civil engineer and my mother was a teacher.
• Father worked as a civil engineer

• Mother was a teacher

• Both are retired now
Answered by AI
Add your answer
Q4. Have you ever visited Delhi earlier
Ans. 
Yes, I have visited Delhi earlier for a business trip.
• Visited Delhi for a business trip

• Explored historical sites like Red Fort and Qutub Minar

• Enjoyed local cuisine like butter chicken and chaat
Answered by AI
Add your answer
Q5. How did you reach Noida for interview
Add your answer
Q6. Where are you staying in Noida for interview process
Ans. 
I am staying at a hotel in Sector 18, Noida for the interview process.
• Staying at a hotel in Sector 18, Noida

• Close to the interview location

• Comfortable accommodation for the duration of the process
Answered by AI
Add your answer
Q7. Related family background
Add your answer

Q1. Detailed technical questions about bearing, pump, furnace tubes (1st and 2nd pass)MOC, TLE MOC, heat exchanger tube MOC, TEMA codes and classification etc.
Add your answer
Q2. Decoking process of cracking furnace, Naphtha circuit of furnace with sketches,
Ans. 
Decoking process involves removing coke deposits from cracking furnace and naphtha circuit to maintain efficiency.
• Decoking process involves burning off coke deposits using controlled combustion.

• Mechanical decoking involves using high-pressure water jets to remove coke deposits.

• Chemical decoking involves using solvents or acids to dissolve coke deposits.

• Regular decoking is essential to prevent blockages and maintain fur
Answered by AI
Add your answer
Q3. Detailed refrigeration cycles
Ans. 
Refrigeration cycles are thermodynamic processes used in refrigerators and air conditioners to transfer heat from a low temperature reservoir to a high temperature reservoir.
• Refrigeration cycles typically involve four main components: compressor, condenser, expansion valve, and evaporator.

• The refrigerant undergoes a cycle of compression, condensation, expansion, and evaporation to absorb heat from the space being coole...read more
Answered by AI
Add your answer
Q4. Safety related questions which I couldn't answer well
Add your answer
Q5. Safety procedures before starting of hot job
Ans. 
Safety procedures before starting a hot job include obtaining a hot work permit, conducting a hazard assessment, ensuring proper ventilation, and having fire extinguishing equipment nearby.
• Obtain a hot work permit before starting any hot job

• Conduct a hazard assessment to identify potential risks

• Ensure proper ventilation in the work area to prevent buildup of flammable gases

• Have fire extinguishing equipment nearby and r
Answered by AI
Add your answer
Q6. Furnace tubes Welding related questions
Add your answer
Q7. Scaffolding and insulation related general questions (easy)
Add your answer

Q1. How will you identify if a pump is cavitating while working on a DCS panel?
Ans. 
To identify if a pump is cavitating while working on a DCS panel, you can look for certain indicators.
• Monitor the pump's suction pressure. If it is fluctuating or dropping below the specified range, it may indicate cavitation.

• Check the pump's discharge pressure. If it is higher than normal, it could be a sign of cavitation.

• Listen for unusual noises such as a rattling or grinding sound coming from the pump.

• Inspect the p...read more
Answered by AI
View 2 more answers
Q2. How would you prepare a hydrocarbon vessel for vessel entry?
Ans. 
To prepare a hydrocarbon vessel for vessel entry, follow these steps:
• Ensure the vessel is properly isolated from the process and all sources of energy

• Ventilate the vessel to remove any flammable or toxic gases

• Perform a thorough inspection of the vessel for any signs of leaks or damage

• Implement proper lockout/tagout procedures to prevent accidental activation of equipment

• Provide appropriate personal protective equipment...read more
Answered by AI
View 2 more answers