Upload Button Icon Add office photos

Filter interviews by

Ramsis Engineering Piping Supervisor Interview Questions and Answers for Experienced

Updated 16 Dec 2020

Ramsis Engineering Piping Supervisor Interview Experiences for Experienced

1 interview found

Interview Questionnaire 

1 Question

  • Q1. Two equipment in site but equipment in between goes to pipe centre fw welding after complete how to the hydrotest?
  • Ans. 

    The hydrotest can be conducted after completing the welding of the pipe center fw.

    • Ensure that the equipment on both ends of the pipe are ready for the hydrotest.

    • Isolate the section of the pipe where the welding was done using blinds or spectacle blinds.

    • Connect the hydrotest pump to one end of the pipe and fill it with water.

    • Increase the pressure gradually to the required test pressure and hold it for the specified dura...

  • Answered by AI

Interview questions from similar companies

Interview experience
4
Good
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
-

I applied via Naukri.com and was interviewed in Nov 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(13 Questions)

  • Q1. How much carbon percentage in Carbon Steel
  • Ans. 

    The carbon percentage in carbon steel varies from 0.05% to 2.0% depending on the grade.

    • Carbon steel is an alloy of iron and carbon.

    • The amount of carbon in carbon steel determines its strength and hardness.

    • Low carbon steel contains less than 0.3% carbon, while high carbon steel contains more than 0.6% carbon.

    • Some common grades of carbon steel and their carbon percentage are: A36 (0.26%), 1018 (0.18%), and 1045 (0.45%).

  • Answered by AI
  • Q2. What is difference between concentric and eccentric reducer
  • Ans. 

    Concentric reducers have a common centerline while eccentric reducers have an offset centerline.

    • Concentric reducers are used in vertical piping systems to prevent accumulation of air pockets.

    • Eccentric reducers are used in horizontal piping systems to prevent accumulation of solids or liquids.

    • Concentric reducers are symmetrical while eccentric reducers are not.

    • Concentric reducers are easier to manufacture and install th

  • Answered by AI
  • Q3. Which reinforcement fittings used in piping
  • Ans. 

    Reinforcement fittings are used to strengthen and support piping systems.

    • Common reinforcement fittings include tees, elbows, reducers, and couplings.

    • Telescoping fittings are used to adjust the length of piping systems.

    • Flange fittings are used to connect pipes to other equipment or structures.

    • Saddles are used to support piping systems on walls or ceilings.

    • Reinforcement fittings can be made of various materials, includin...

  • Answered by AI
  • Q4. Why elbo let used in piping
  • Ans. 

    Elbow lets change the direction of flow in piping system.

    • Elbows are used to change the direction of flow in a piping system.

    • They come in different angles such as 45°, 90° and 180°.

    • They are available in different materials such as PVC, copper, steel, etc.

    • Elbows can be welded or threaded onto the piping system.

    • They are commonly used in plumbing, HVAC, and industrial piping systems.

  • Answered by AI
  • Q5. If we have to replace bypass valve on top of vessel and plant is running, then how to replace that valve ??
  • Ans. 

    The bypass valve can be replaced by isolating the vessel, depressurizing it, and then replacing the valve.

    • Isolate the vessel by closing the inlet and outlet valves

    • Depressurize the vessel by venting the gas or liquid

    • Remove the old valve and install the new one

    • Repressurize the vessel and open the inlet and outlet valves

  • Answered by AI
  • Q6. What is Permit to work
  • Ans. 

    Permit to work is a formal written system used to control high-risk activities.

    • It is a document that outlines the work to be done and the hazards associated with it.

    • It is used to ensure that all necessary safety precautions are taken before work begins.

    • It is issued by a competent authority and must be signed by all parties involved in the work.

    • Examples include hot work permits, confined space permits, and excavation pe

  • Answered by AI
  • Q7. Tell me about yourself and your experience
  • Q8. What is isolation and how many types of isolation
  • Ans. 

    Isolation is the process of separating a system or equipment from its energy source to ensure safety during maintenance or repair.

    • Isolation involves disconnecting a system or equipment from its power source, locking it out, and tagging it to prevent accidental re-energization.

    • There are two types of isolation: electrical isolation and mechanical isolation.

    • Electrical isolation involves disconnecting the electrical supply...

  • Answered by AI
  • Q9. What is positive isolation
  • Ans. 

    Positive isolation is the process of completely isolating a section of a system to prevent any flow or transfer of material.

    • Positive isolation is achieved by using valves, blinds, or other physical barriers to completely block the flow of material.

    • It is important for safety and maintenance purposes, as it allows workers to safely perform tasks without the risk of exposure to hazardous materials.

    • Examples of positive iso...

  • Answered by AI
  • Q10. How to do positive isolation
  • Ans. 

    Positive isolation is the process of completely isolating a section of piping or equipment from the rest of the system to perform maintenance or repairs.

    • Identify the section of piping or equipment that needs to be isolated

    • Close all valves and block all lines leading to and from the section

    • Use blind flanges or spectacle blinds to physically block the section

    • Ensure that the isolation is secure and pressure tested before ...

  • Answered by AI
  • Q11. When we do nitrogen purging and why it's required
  • Ans. 

    Nitrogen purging is done to remove impurities and oxygen from pipelines before commissioning or maintenance work.

    • Nitrogen purging is done to create an inert atmosphere inside the pipeline to prevent explosions or fires.

    • It is required before commissioning or maintenance work to remove impurities and oxygen from the pipeline.

    • Nitrogen purging is also done to prevent corrosion and contamination of the pipeline.

    • It is common...

  • Answered by AI
  • Q12. What is difference between pipe and tube
  • Ans. 

    Pipes are used to transport fluids and gases, while tubes are used for structural purposes.

    • Pipes have a standardized outer diameter and wall thickness, while tubes have a standardized inner diameter and wall thickness.

    • Pipes are typically round, while tubes can be round, square, or rectangular.

    • Pipes are often used in plumbing and HVAC systems, while tubes are used in construction and engineering applications.

    • Pipes are u...

  • Answered by AI
  • Q13. Which pipe material or standard used in past experience
  • Ans. 

    I have experience working with various pipe materials and standards including carbon steel, stainless steel, and PVC.

    • I have worked with carbon steel pipes in a power plant project.

    • I have also worked with stainless steel pipes in a pharmaceutical plant project.

    • In a water treatment plant project, I have worked with PVC pipes.

    • I am familiar with ASME B31.3, API 5L, and ASTM standards for pipe materials and welding procedur

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Read your resume carefully, be confident, eye contact and imagine that you knew better than them , if you don't know say I don't know , don't answer in stories , always prepare for interview as per company requirements.

I applied via Recruitment Consulltant and was interviewed before Sep 2021. There was 1 interview round.

Round 1 - HR 

(1 Question)

  • Q1. What do you face a big problem during turnaround
  • Ans. Can you explained basic difference between ASME and ASTM
  • Answered Anonymously

Interview Preparation Tips

Interview preparation tips for other job seekers - I face normally and heard carefully question,
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Naukri.com and was interviewed in Feb 2024. There were 2 interview rounds.

Round 1 - Aptitude Test 

Question answer related piping job ,material related, manpower handling etc...

Round 2 - Technical 

(5 Questions)

  • Q1. Piping related question, Piping material astm code
  • Q2. Types of piping drawing
  • Ans. 

    Types of piping drawings include Piping and Instrumentation Diagrams (P&IDs), Isometric drawings, and Orthographic drawings.

    • Piping and Instrumentation Diagrams (P&IDs) show the piping system along with instruments and control devices.

    • Isometric drawings show the 3D representation of the piping system.

    • Orthographic drawings show the top, front, and side views of the piping system.

  • Answered by AI
  • Q3. Difference b/w construction and fabrication drawing?
  • Ans. 

    Construction drawings show how a structure will be built, while fabrication drawings provide detailed instructions for manufacturing individual components.

    • Construction drawings focus on overall structure layout and dimensions

    • Fabrication drawings provide detailed instructions for manufacturing individual components

    • Construction drawings are used by contractors on site, fabrication drawings are used by manufacturers in wo...

  • Answered by AI
  • Q4. Piping material code ?
  • Ans. 

    Piping material code refers to the standards and specifications used for selecting materials for piping systems.

    • Piping material codes are used to ensure the proper selection of materials based on factors like pressure, temperature, and fluid being transported.

    • Common piping material codes include ASME B31.3 for process piping, ASTM for materials specifications, and API for oil and gas piping.

    • These codes provide guidelin...

  • Answered by AI
  • Q5. Difference b/w pipe and tubes
  • Ans. 

    Pipes are used to transport fluids or gases, while tubes are used for structural applications or heat transfer.

    • Pipes are measured by their inside diameter, while tubes are measured by their outside diameter.

    • Pipes are typically round in shape, while tubes can be round, square, or rectangular.

    • Pipes are commonly used in plumbing, HVAC systems, and oil and gas industries, while tubes are used in construction, automotive, a

  • Answered by AI

Interview Preparation Tips

Topics to prepare for Reliance Industries Piping Engineer interview:
  • Piping
  • Statatic Equipment
Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all tips
Round 2 - Technical 

(5 Questions)

  • Q1. Work experience, country name, types of work, manpower handling etc
  • Q2. Punjlloyd ltd ,brouge 2 project,abudhabi
  • Q3. Allkulaib int kuwait ,subiya power plant
  • Q4. Dyam punjlloyd ,saudi arabia ,satrop projects
  • Q5. Towell eng, oman orpic (srip extension projects)
Round 3 - Aptitude Test 

Manpower nhandling only

Interview Preparation Tips

Interview preparation tips for other job seekers - try a EPC company blike perrofac

I applied via Recruitment Consulltant and was interviewed in Aug 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Properly align and format text in your resume. A recruiter will have to spend more time reading poorly aligned text, leading to high chances of rejection.
View all tips
Round 2 - Interview 

(2 Questions)

  • Q1. General questions related to past work experience and previous job changes.
  • Q2. It was an interview to check personality traits rather that technical knowledge

Interview Preparation Tips

Interview preparation tips for other job seekers - Remain honest, positive and calm during the interview. Don’t say negative things about past employers/ jobs.
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
-

I applied via Naukri.com and was interviewed in Nov 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Double-check your resume for any spelling mistakes. The recruiter may consider spelling mistakes as careless behavior or poor communication skills.
View all tips
Round 2 - Technical 

(13 Questions)

  • Q1. How much carbon percentage in Carbon Steel
  • Ans. 

    The carbon percentage in carbon steel varies from 0.05% to 2.0% depending on the grade.

    • Carbon steel is an alloy of iron and carbon.

    • The amount of carbon in carbon steel determines its strength and hardness.

    • Low carbon steel contains less than 0.3% carbon, while high carbon steel contains more than 0.6% carbon.

    • Some common grades of carbon steel and their carbon percentage are: A36 (0.26%), 1018 (0.18%), and 1045 (0.45%).

  • Answered by AI
  • Q2. What is difference between concentric and eccentric reducer
  • Ans. 

    Concentric reducers have a common centerline while eccentric reducers have an offset centerline.

    • Concentric reducers are used in vertical piping systems to prevent accumulation of air pockets.

    • Eccentric reducers are used in horizontal piping systems to prevent accumulation of solids or liquids.

    • Concentric reducers are symmetrical while eccentric reducers are not.

    • Concentric reducers are easier to manufacture and install th

  • Answered by AI
  • Q3. Which reinforcement fittings used in piping
  • Ans. 

    Reinforcement fittings are used to strengthen and support piping systems.

    • Common reinforcement fittings include tees, elbows, reducers, and couplings.

    • Telescoping fittings are used to adjust the length of piping systems.

    • Flange fittings are used to connect pipes to other equipment or structures.

    • Saddles are used to support piping systems on walls or ceilings.

    • Reinforcement fittings can be made of various materials, includin...

  • Answered by AI
  • Q4. Why elbo let used in piping
  • Ans. 

    Elbow lets change the direction of flow in piping system.

    • Elbows are used to change the direction of flow in a piping system.

    • They come in different angles such as 45°, 90° and 180°.

    • They are available in different materials such as PVC, copper, steel, etc.

    • Elbows can be welded or threaded onto the piping system.

    • They are commonly used in plumbing, HVAC, and industrial piping systems.

  • Answered by AI
  • Q5. If we have to replace bypass valve on top of vessel and plant is running, then how to replace that valve ??
  • Ans. 

    The bypass valve can be replaced by isolating the vessel, depressurizing it, and then replacing the valve.

    • Isolate the vessel by closing the inlet and outlet valves

    • Depressurize the vessel by venting the gas or liquid

    • Remove the old valve and install the new one

    • Repressurize the vessel and open the inlet and outlet valves

  • Answered by AI
  • Q6. What is Permit to work
  • Ans. 

    Permit to work is a formal written system used to control high-risk activities.

    • It is a document that outlines the work to be done and the hazards associated with it.

    • It is used to ensure that all necessary safety precautions are taken before work begins.

    • It is issued by a competent authority and must be signed by all parties involved in the work.

    • Examples include hot work permits, confined space permits, and excavation pe

  • Answered by AI
  • Q7. Tell me about yourself and your experience
  • Q8. What is isolation and how many types of isolation
  • Ans. 

    Isolation is the process of separating a system or equipment from its energy source to ensure safety during maintenance or repair.

    • Isolation involves disconnecting a system or equipment from its power source, locking it out, and tagging it to prevent accidental re-energization.

    • There are two types of isolation: electrical isolation and mechanical isolation.

    • Electrical isolation involves disconnecting the electrical supply...

  • Answered by AI
  • Q9. What is positive isolation
  • Ans. 

    Positive isolation is the process of completely isolating a section of a system to prevent any flow or transfer of material.

    • Positive isolation is achieved by using valves, blinds, or other physical barriers to completely block the flow of material.

    • It is important for safety and maintenance purposes, as it allows workers to safely perform tasks without the risk of exposure to hazardous materials.

    • Examples of positive iso...

  • Answered by AI
  • Q10. How to do positive isolation
  • Ans. 

    Positive isolation is the process of completely isolating a section of piping or equipment from the rest of the system to perform maintenance or repairs.

    • Identify the section of piping or equipment that needs to be isolated

    • Close all valves and block all lines leading to and from the section

    • Use blind flanges or spectacle blinds to physically block the section

    • Ensure that the isolation is secure and pressure tested before ...

  • Answered by AI
  • Q11. When we do nitrogen purging and why it's required
  • Ans. 

    Nitrogen purging is done to remove impurities and oxygen from pipelines before commissioning or maintenance work.

    • Nitrogen purging is done to create an inert atmosphere inside the pipeline to prevent explosions or fires.

    • It is required before commissioning or maintenance work to remove impurities and oxygen from the pipeline.

    • Nitrogen purging is also done to prevent corrosion and contamination of the pipeline.

    • It is common...

  • Answered by AI
  • Q12. What is difference between pipe and tube
  • Ans. 

    Pipes are used to transport fluids and gases, while tubes are used for structural purposes.

    • Pipes have a standardized outer diameter and wall thickness, while tubes have a standardized inner diameter and wall thickness.

    • Pipes are typically round, while tubes can be round, square, or rectangular.

    • Pipes are often used in plumbing and HVAC systems, while tubes are used in construction and engineering applications.

    • Pipes are u...

  • Answered by AI
  • Q13. Which pipe material or standard used in past experience
  • Ans. 

    I have experience working with various pipe materials and standards including carbon steel, stainless steel, and PVC.

    • I have worked with carbon steel pipes in a power plant project.

    • I have also worked with stainless steel pipes in a pharmaceutical plant project.

    • In a water treatment plant project, I have worked with PVC pipes.

    • I am familiar with ASME B31.3, API 5L, and ASTM standards for pipe materials and welding procedur

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Read your resume carefully, be confident, eye contact and imagine that you knew better than them , if you don't know say I don't know , don't answer in stories , always prepare for interview as per company requirements.

I applied via Recruitment Consulltant and was interviewed before Sep 2021. There was 1 interview round.

Round 1 - HR 

(1 Question)

  • Q1. What do you face a big problem during turnaround
  • Ans. Can you explained basic difference between ASME and ASTM
  • Answered Anonymously

Interview Preparation Tips

Interview preparation tips for other job seekers - I face normally and heard carefully question,
Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(1 Question)

  • Q1. Transformers, motor, maintenance and operation
Round 2 - HR 

(1 Question)

  • Q1. Basic salary family background
Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Do not use an unprofessional email address such as cool_boy@email.com. It shows a lack of professionalism by the candidate.
View all tips
Round 2 - Technical 

(4 Questions)

  • Q1. Saudi aramco engineering standards.
  • Ans. 

    Saudi Aramco Engineering Standards are guidelines and specifications used in engineering projects for Saudi Aramco.

    • Saudi Aramco Engineering Standards cover various aspects of engineering design, materials, construction, and operation.

    • These standards ensure consistency, quality, and safety in all engineering projects undertaken by Saudi Aramco.

    • Examples of areas covered by the standards include piping design, electrical ...

  • Answered by AI
  • Q2. Design related discussions
  • Q3. Safe practices in design
  • Ans. 

    Safe practices in design involve considering potential hazards, following regulations, and prioritizing safety.

    • Identify potential hazards in the design process

    • Follow industry regulations and standards for safety

    • Prioritize safety over cost or convenience

    • Regularly review and update safety protocols

    • Include safety features in the design, such as emergency shut-off valves

    • Consider environmental impact and sustainability in d

  • Answered by AI
  • Q4. Quality of deliverables
  • Ans. 

    Quality of deliverables is crucial for successful project completion.

    • Ensuring accuracy and completeness of drawings and documents

    • Adhering to project specifications and standards

    • Regularly reviewing and revising deliverables to meet client requirements

    • Seeking feedback from stakeholders to improve quality

    • Using software tools effectively to enhance deliverables

    • Maintaining clear communication with team members for consisten

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Familiarization with the clients standard and procedures

Skills evaluated in this interview

Tell us how to improve this page.

Interview Questions from Similar Companies

TCS Interview Questions
3.7
 • 10.1k Interviews
Siemens Interview Questions
4.1
 • 416 Interviews
Bosch Interview Questions
4.2
 • 325 Interviews
Thermax Limited Interview Questions
4.2
 • 231 Interviews
Cummins Interview Questions
4.3
 • 227 Interviews
Shell Interview Questions
4.0
 • 189 Interviews
View all
Ramsis Engineering Piping Supervisor Salary
based on 4 salaries
₹0.9 L/yr - ₹4.8 L/yr
67% less than the average Piping Supervisor Salary in India
View more details

Ramsis Engineering Piping Supervisor Reviews and Ratings

based on 1 review

4.0/5

Rating in categories

5.0

Skill development

2.0

Work-Life balance

5.0

Salary & Benefits

3.0

Job Security

4.0

Company culture

3.0

Promotions/Appraisal

2.0

Work Satisfaction

Explore 1 Review and Rating
Senior Engineer
5 salaries
unlock blur

₹8.4 L/yr - ₹20 L/yr

Construction Management
5 salaries
unlock blur

₹15.5 L/yr - ₹40 L/yr

Mechanical Supervisor
5 salaries
unlock blur

₹6.5 L/yr - ₹8.5 L/yr

Mechanical Engineer
4 salaries
unlock blur

₹12 L/yr - ₹18 L/yr

Safety Engineer
4 salaries
unlock blur

₹7.2 L/yr - ₹12 L/yr

Explore more salaries
Compare Ramsis Engineering with

Larsen & Toubro Limited

4.0
Compare

TCS

3.7
Compare

BHEL

4.2
Compare

Thermax Limited

4.2
Compare

Calculate your in-hand salary

Confused about how your in-hand salary is calculated? Enter your annual salary (CTC) and get your in-hand salary
Did you find this page helpful?
Yes No
write
Share an Interview