Filter interviews by
I applied via Approached by Company and was interviewed in Oct 2022. There were 2 interview rounds.
Top trending discussions
SPC stands for Statistical Process Control. It is a method of quality control that uses statistical methods to monitor and control a process.
SPC involves collecting and analyzing data to identify and reduce variation in a process
It helps to ensure that a process is operating within its specified limits and is capable of producing consistent results
Examples of SPC tools include control charts, histograms, and Pareto cha...
Corrective action is taken to address and resolve existing problems, while preventive action is taken to prevent potential problems from occurring.
Corrective action focuses on addressing and resolving existing problems or nonconformities.
Preventive action focuses on identifying and eliminating potential problems before they occur.
Corrective action is reactive, while preventive action is proactive.
Corrective action aims...
I am a detail-oriented Quality Engineer with a passion for continuous improvement and problem-solving.
Detail-oriented with a focus on quality standards
Passionate about continuous improvement
Skilled in problem-solving and root cause analysis
The steps for demin wheels involve cleaning, inspecting, repairing, and testing.
Clean the wheels thoroughly to remove any dirt or debris.
Inspect the wheels for any damage or defects.
Repair any issues found, such as replacing worn-out parts or fixing cracks.
Test the wheels to ensure they meet quality standards and perform as expected.
Hardness is the measure of a material's resistance to indentation or scratching.
Hardness is a property of materials that determines their ability to withstand deformation
It is often measured using tests like the Rockwell, Brinell, or Vickers hardness tests
Hardness can be influenced by factors such as the material's composition, heat treatment, and microstructure
Higher hardness generally indicates greater strength and d...
To upgrade suppliers, establish clear quality standards, conduct regular audits, provide feedback and support for improvement, and consider alternative suppliers.
Establish clear quality standards and communicate them to suppliers
Conduct regular audits to assess supplier performance and identify areas for improvement
Provide feedback and support to suppliers to help them meet quality standards
Consider alternative supplie...
Supplier selection criteria are the factors and considerations used to evaluate and choose suppliers for a company's procurement needs.
Quality and reliability of products or services
Supplier's financial stability and ability to meet demand
Supplier's track record and reputation
Cost and pricing
Supplier's location and proximity to the company
Supplier's compliance with industry standards and regulations
Supplier's capacity ...
I was interviewed before Apr 2021.
Toe in and toe out are terms used to describe the angle of the wheels on a vehicle.
Toe in refers to the front of the wheels being closer together than the back of the wheels.
Toe out refers to the front of the wheels being further apart than the back of the wheels.
Toe in/out can affect the handling and tire wear of a vehicle.
Proper alignment is important for safety and optimal performance.
Wheel balancing is the process of equalizing the weight of a tire and wheel assembly so that it spins smoothly at high speeds.
It involves adding or removing weights to the wheel to balance it
Unbalanced wheels can cause vibrations, uneven tire wear, and steering issues
It is important to balance wheels regularly, especially after getting new tires or wheels
Examples of wheel balancing equipment include wheel balancers and
Caster camber angle is the angle between the vertical axis of the wheel and the steering axis.
It affects the stability and handling of the vehicle.
Caster angle helps in straight-line stability and steering returnability.
Camber angle helps in tire wear and cornering ability.
Welding defects are imperfections that occur during the welding process.
Common welding defects include porosity, undercutting, and incomplete fusion.
Porosity is caused by gas pockets trapped in the weld, while undercutting is a groove at the base of the weld.
Incomplete fusion occurs when the weld metal does not fuse completely with the base metal.
Welding defects can weaken the weld and compromise its integrity.
Quality ...
Vernier caliper least count is the smallest measurement that can be read on the scale of the caliper.
The least count of a Vernier caliper is usually 0.02 mm or 0.05 mm.
It is determined by dividing the smallest division on the main scale by the number of divisions on the Vernier scale.
For example, if the smallest division on the main scale is 1 mm and there are 20 divisions on the Vernier scale, the least count would be
The type of welding used depends on the material being welded and the desired strength of the joint.
Common types of welding include MIG, TIG, stick, and flux-cored welding.
MIG welding is often used for welding aluminum and steel.
TIG welding is commonly used for welding thin materials and for precision welding.
Stick welding is often used for welding thicker materials and in outdoor environments.
Flux-cored welding is sim...
What your view on alcohol and alcohol bane or not and why
I applied via Campus Placement and was interviewed before Oct 2020. There was 1 interview round.
posted on 19 May 2021
I applied via Naukri.com and was interviewed in Nov 2020. There were 4 interview rounds.
posted on 26 May 2020
I applied via Walk-in and was interviewed in Apr 2020. There were 3 interview rounds.
The 7 QC tools are a set of basic quality control tools used to identify and solve quality problems.
Check sheets
Control charts
Histograms
Pareto charts
Scatter diagrams
Stratification
Cause-and-effect diagrams
As a Quality Engineer in my previous company, I was responsible for ensuring product quality, conducting audits, and implementing quality control processes.
Conducted product quality inspections and audits
Implemented quality control processes to improve product quality
Analyzed data to identify areas for improvement
Collaborated with cross-functional teams to address quality issues
Ensured compliance with industry standard
QA focuses on preventing defects while QC focuses on identifying and fixing defects.
QA is a proactive process that involves planning, designing, and executing tests to prevent defects from occurring.
QC is a reactive process that involves identifying defects through testing and then fixing them.
QA is focused on the entire software development life cycle while QC is focused on the testing phase.
Examples of QA activities ...
posted on 25 Jan 2021
I applied via Walk-in and was interviewed in Dec 2020. There were 3 interview rounds.
posted on 12 Sep 2021
I applied via Naukri.com and was interviewed before Sep 2020. There was 1 interview round.
posted on 15 Feb 2022
Engineer
92
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
64
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Engineer
63
salaries
| ₹0 L/yr - ₹0 L/yr |
Production Engineer
60
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Engineer
57
salaries
| ₹0 L/yr - ₹0 L/yr |
Samvardhana Motherson Group
Bharat Forge
TVS Sundram Fasteners
Rane Holdings