Filter interviews by
I was interviewed in Aug 2016.
Top trending discussions
posted on 26 Dec 2024
I applied via Recruitment Consulltant and was interviewed in Jun 2024. There was 1 interview round.
The power flow at my previous company involved analyzing and optimizing the distribution of electrical power throughout the system.
Studied power flow patterns to ensure efficient distribution of electricity
Utilized software like ETAP or PSS/E for power flow analysis
Implemented measures to reduce power losses and improve system reliability
Collaborated with other engineers to address power flow issues
Regularly monitored
Operation and maintenance procedures for transformer feeders and motor feeders involve regular inspections, testing, and preventive maintenance to ensure optimal performance and safety.
Regularly inspect transformer and motor feeders for signs of wear, damage, or overheating.
Perform routine testing to check for proper voltage levels, insulation resistance, and overall functionality.
Conduct preventive maintenance such as...
A contactor is an electrical device used to switch an electrical circuit on or off, while BMR stands for Basic Maintenance Ratio in electrical engineering.
Contactor is used to control electric motors, lighting, heating, and other electrical loads
BMR is a ratio used to determine the maintenance cost of a system relative to its initial cost
Contactor typically consists of a coil, contacts, and an enclosure
BMR is calculate...
Low forward power in a generator refers to the situation where the power output of the generator is lower than expected or required.
Low forward power can be caused by issues such as mechanical problems, fuel supply issues, or electrical faults.
It can result in reduced efficiency, poor performance, and potential damage to the generator.
Regular maintenance and monitoring can help prevent and address low forward power iss...
To sync your power plant with the grid, you need to match the frequency and phase of the plant with the grid.
Ensure the frequency of the power plant matches the grid frequency (usually 50 or 60 Hz)
Synchronize the phase angle of the power plant with the grid
Use synchronization equipment such as synchronizing relays and synchroscopes
Gradually increase the power output of the plant to match the grid demand
Monitor the sync
Rotten egg on inverted pen, social media
HSE plan is a detailed strategy outlining how health, safety, and environmental risks will be managed. HSE Policy is a company's commitment to health, safety, and environmental protection. Safety program is a set of procedures and initiatives to ensure workplace safety.
HSE plan is a comprehensive document that outlines how an organization will identify, assess, and control health, safety, and environmental risks.
HSE Po...
Safety policy is a set of rules and guidelines implemented by an organization to ensure the safety and well-being of its employees.
Safety policy outlines the procedures and protocols to be followed in order to prevent accidents and injuries in the workplace.
It includes guidelines for emergency response, hazard identification, safety training, and personal protective equipment.
Examples of safety policies include mandato...
Safety commitment is the dedication of an organization to prioritize and uphold safety standards, while a safety program is a structured plan to implement safety measures.
Safety commitment involves top management support and involvement in safety initiatives
Safety program includes policies, procedures, training, and audits to ensure a safe work environment
Examples of safety programs include regular safety meetings, haz...
The BOCW Act stands for Building and Other Construction Workers Act, which aims to regulate the safety, health, and welfare of construction workers. A safety plan is a document outlining safety measures and procedures to prevent accidents and injuries on a construction site.
BOCW Act is a legislation in India that focuses on the welfare of construction workers
It mandates safety measures, health provisions, and welfare a...
Accident investigation at workplace involves identifying root causes, gathering evidence, interviewing witnesses, and implementing corrective actions.
Identify the accident scene and secure it to preserve evidence
Interview witnesses to gather information about the incident
Review relevant documents such as safety procedures and training records
Analyze the sequence of events leading up to the accident
Identify root causes ...
posted on 29 Mar 2024
I applied via Recruitment Consulltant and was interviewed before Mar 2023. There was 1 interview round.
I applied via Company Website and was interviewed in Apr 2022. There was 1 interview round.
posted on 29 Nov 2024
I design, develop, and test electrical systems and equipment.
Designing electrical systems for buildings or products
Developing prototypes and testing them for functionality
Collaborating with other engineers and technicians
Troubleshooting and resolving electrical issues
Staying updated on industry trends and advancements
I applied via Company Website and was interviewed in Apr 2022. There was 1 interview round.
posted on 7 Jun 2024
I applied via Recruitment Consulltant and was interviewed in Dec 2023. There was 1 interview round.
based on 1 interview
Interview experience
based on 13 reviews
Rating in categories
Executive Engineer
79
salaries
| ₹12 L/yr - ₹35 L/yr |
Assistant Executive Engineer
45
salaries
| ₹8.4 L/yr - ₹27 L/yr |
Mechanical Technician
43
salaries
| ₹0.8 L/yr - ₹6.2 L/yr |
Safety Officer
39
salaries
| ₹2 L/yr - ₹9.7 L/yr |
Mechanical Engineer
37
salaries
| ₹3.6 L/yr - ₹14.2 L/yr |
Reliance Industries
Indian Oil Corporation
Bharat Petroleum
Hindustan Petroleum