Upload Button Icon Add office photos

Jacobs Engineering Group

Compare button icon Compare button icon Compare

Filter interviews by

Jacobs Engineering Group Electrical & Instrumentation Engineer Interview Questions and Answers

Updated 26 Aug 2022

Jacobs Engineering Group Electrical & Instrumentation Engineer Interview Experiences

1 interview found

I applied via Referral and was interviewed in Jul 2022. There was 1 interview round.

Round 1 - Technical 

(1 Question)

  • Q1. Documents needed for installation of any flow meter??
  • Ans. 

    Documents required for installation of a flow meter

    • Manufacturer's installation manual

    • Piping and instrumentation diagram (P&ID)

    • Electrical wiring diagram

    • Calibration certificate

    • Material test certificate (MTC) for piping

    • Safety data sheet (SDS) for chemicals used in installation

    • Permit for installation

    • Quality assurance plan (QAP)

    • As-built drawings

  • Answered by AI

Interview Preparation Tips

Topics to prepare for Jacobs Engineering Group Electrical & Instrumentation Engineer interview:
  • Instrumentation basics
Interview preparation tips for other job seekers - Very very well manner interview ,so friendly and lots of advise they will give positive.

Interview questions from similar companies

I applied via Company Website

Interview Questionnaire 

3 Questions

  • Q1. General questions about instruments, calibration process
  • Q2. Control valve calibration,
  • Q3. Knowledge about PLC

Interview Preparation Tips

Interview preparation tips for other job seekers - Keep your basic ready and give practical answers

I applied via Walk-in and was interviewed in Nov 2020. There were 4 interview rounds.

Interview Questionnaire 

1 Question

  • Q1. They Have been asked about Civil engineering questions and its some what tough but if you prepare it's easy and GATE questions only

Interview Preparation Tips

Interview preparation tips for other job seekers - First you have to clear the written test then technical round and next HR round if you clear written then your eligible for technical round in TR they will be asking you which is favourite subjects and questions then HR but you have to go any site

I applied via Walk-in and was interviewed before Jan 2021. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Least count of staff reading
  • Ans. 

    The least count of staff reading is the smallest measurement that can be read and recorded using the staff.

    • The least count is determined by the smallest division on the staff scale.

    • It is usually expressed in millimeters or centimeters.

    • For example, if the smallest division on the staff scale is 1 mm, then the least count is 1 mm.

    • The least count is important in accurately measuring and recording distances in civil engine

  • Answered by AI
  • Q2. Intial setting time of concrete
  • Ans. 30 minutes
  • Answered by lyricalcricket
Round 3 - HR 

(5 Questions)

  • Q1. Share details of your previous job.
  • Q2. What are your salary expectations?
  • Q3. Why are you looking for a change?
  • Q4. Where do you see yourself in 5 years?
  • Q5. Tell me about yourself.

Interview Preparation Tips

Topics to prepare for Megha Engineering & Infrastructures Civil Engineer interview:
  • Concrete technology , surveying,
Interview preparation tips for other job seekers - It is based on your luck , if your job location giving at g.m relatives team, your growth is collapsed.

Interview Questionnaire 

1 Question

  • Q1. How to draw an SFD and BMD for simply supported beam under UDL of 10KM/m

Interview Preparation Tips

Interview preparation tips for other job seekers - They are asking so much question if you are a fresher and just passed out. They are full of field knowledge. Asked about family background too and many things which can't be explained.

Interview Questionnaire 

1 Question

  • Q1. Core subjects

Interview Preparation Tips

Interview preparation tips for other job seekers - I will give one simple trick to crack any *core company's* interview.

1) just by heart all the theory Portion of fluid mechanics , thermodynamics , som & machine design. In interview what you did in extra curricular activities doesn't matter. All they want is bookish knowledge.

I applied via Referral and was interviewed before Jul 2020. There were 3 interview rounds.

Interview Questionnaire 

1 Question

  • Q1. Purely Technical

Interview Preparation Tips

Interview preparation tips for other job seekers - Do not give answer in hurry. Be calm. Always be specific.

I appeared for an interview in Aug 2017.

Interview Questionnaire 

5 Questions

  • Q1. Tell me about yourself, Include you projects in detail!
  • Ans. 

    I am a software engineer with experience in various projects.

    • Developed a mobile app for a retail company to manage inventory and sales.

    • Created a web application for a healthcare organization to track patient records.

    • Contributed to a team project for a financial institution to build a secure online banking platform.

  • Answered by AI
  • Q2. Would you go for higher studies?
  • Ans. 

    Yes, I would go for higher studies.

    • Higher studies can provide advanced knowledge and skills in a specific field.

    • It can open up more career opportunities and increase earning potential.

    • Higher studies often involve research and practical experience.

    • It allows for specialization and expertise in a particular subject.

    • Examples of higher studies include pursuing a master's or doctoral degree.

    • Continuing education and professio...

  • Answered by AI
  • Q3. Why Alstom?
  • Ans. 

    Alstom is a leading global provider of innovative and sustainable transportation solutions.

    • Alstom has a strong track record in delivering high-quality transportation solutions.

    • The company has a global presence and a wide range of products and services.

    • Alstom is committed to sustainability and has a focus on developing environmentally-friendly solutions.

    • The company has a strong reputation for innovation and technologica...

  • Answered by AI
  • Q4. Are you okay with Bangalore location?
  • Ans. 

    Yes, I am okay with Bangalore location.

    • I am open to working in Bangalore.

    • I have no issues with the Bangalore location.

    • I am comfortable with the Bangalore location.

  • Answered by AI
  • Q5. What is Leadership to you?
  • Ans. 

    Leadership is the ability to inspire and guide others towards a common goal, while fostering a positive and inclusive environment.

    • Leadership involves setting a clear vision and goals for a team or organization.

    • A leader should possess strong communication and interpersonal skills to effectively motivate and inspire others.

    • Leadership requires making tough decisions and taking responsibility for the outcomes.

    • A good leader...

  • Answered by AI

Interview Preparation Tips

Round: Resume Shortlist
Experience: Although the criteria was CGPA 7 and above, but another shortlist was provided by the company including only those students having CGPA >7.9.
Tips: For getting into Alstom, you need to have good academic performance. Atleast try to be in top 40 of your branch.

Round: Test
Experience: The test was conducted on CoCubes.The Aptitude section included Quantitative ,verbal and LR. Technical section was purely on Btech syllabus.
Tips: You need to have a good command on your aptitude as in the technical section, you'll get random questions from different subjects.
Duration: 1 hour
Total Questions: 60

Round: Group Discussion
Experience: I lead the discussion, conducting it smoothly, I concluded.
Tips: Listen to the instructions carefully and follow them strictly. We were told to interact in a sober way and not to interrupt others. I started the discussion, and waited for everyone to speak before speaking up the second point.
Duration: 15 minutes

Round: Technical Interview
Experience: The company focused on Design & Development, mainly focused on projects that I have done. I being a part of SAE Collegiate club, have told about my project.Surprisingly, All 45 min - 1 hour of my interview was about this project of mine. Having a good understanding of my project, I nailed the interview!. It was visible clearly on the interviewers face that he was impressed.
I had also managed and lead various activities in my college which further added as an advantage to my presentation.
Tips: When you have some good projects, then that creates a very positive reflection of you. But you should answer each and every question asked to you in the context otherwise it will have a equally bad impact!
I have removed few other projects of mine the previous night. So it's not about the numbers, but about the understanding of the single project in depth.

Round: HR Interview
Tips: Having clarity of thoughts and good knowledge about the company will help you clear this round.

College Name: Motilal Nehru National Institute Of Technology, Allahabad

Interview Questionnaire 

13 Questions

  • Q1. What are the different types of concrete?
  • Ans. 

    There are several types of concrete, including plain, reinforced, pre-stressed, and lightweight.

    • Plain concrete is the most basic type and is used for general construction purposes.

    • Reinforced concrete has steel bars or mesh embedded in it to increase its strength.

    • Pre-stressed concrete is compressed before use to increase its strength and durability.

    • Lightweight concrete is made with lightweight aggregates, such as expand...

  • Answered by AI
  • Q2. What was your minor project?
  • Ans. 

    My minor project was an Android application for tracking daily expenses.

    • Developed using Java and Android Studio

    • Used SQLite database to store data

    • Implemented features like adding expenses, categorizing them, and generating reports

    • Focused on user-friendly UI/UX design

    • Received positive feedback from users during testing

  • Answered by AI
  • Q3. What is the slump value for pumpable concrete?
  • Ans. 

    The slump value for pumpable concrete varies depending on the mix design and application.

    • Slump value is the measure of the consistency of concrete.

    • Pumpable concrete typically has a higher slump value than traditional concrete.

    • The slump value for pumpable concrete can range from 150mm to 200mm.

    • The mix design and application will determine the appropriate slump value for pumpable concrete.

  • Answered by AI
  • Q4. How do you measure slump in field?
  • Ans. 

    Slump is measured by placing a slump cone on a flat surface and filling it with concrete. The cone is then lifted and the slump is measured.

    • Place a slump cone on a flat surface

    • Fill the cone with concrete in three layers

    • Compact each layer with a steel rod

    • Remove the excess concrete from the top of the cone

    • Lift the cone vertically and measure the slump

    • Repeat the process for consistency

  • Answered by AI
  • Q5. What are the tests carried out on aggregates?
  • Ans. 

    Tests carried out on aggregates

    • Sieve analysis to determine particle size distribution

    • Water absorption test to measure the porosity of aggregates

    • Aggregate crushing value test to measure the strength of aggregates

    • Los Angeles abrasion test to measure the resistance to wear and tear

    • Soundness test to measure the resistance to weathering

    • Alkali-silica reaction test to determine the potential for harmful chemical reaction

    • Organ...

  • Answered by AI
  • Q6. Draw the work breakdown structure for a ROOM with foundation
  • Ans. 

    Draw the work breakdown structure for a ROOM with foundation

    • Foundation: excavation, concrete pouring, reinforcement

    • Walls: framing, insulation, drywall

    • Roof: framing, sheathing, shingles

    • Flooring: subfloor, flooring material

    • Electrical: wiring, outlets, switches

    • Plumbing: pipes, fixtures

    • Finishing: painting, trim, hardware

  • Answered by AI
  • Q7. What is the highest grade of concrete you have used?
  • Ans. 

    I have used M50 grade of concrete in a construction project.

    • I have experience in working with high-grade concrete such as M50.

    • I have knowledge of the properties and characteristics of different grades of concrete.

    • I have worked on a construction project where M50 grade of concrete was used for the foundation.

    • I understand the importance of using the right grade of concrete for different types of structures.

  • Answered by AI
  • Q8. SFD and BMD of a beam
  • Ans. 

    SFD and BMD are diagrams used to determine the internal forces and bending moments in a beam.

    • SFD (Shear Force Diagram) shows the variation of shear force along the length of the beam.

    • BMD (Bending Moment Diagram) shows the variation of bending moment along the length of the beam.

    • SFD and BMD are important in designing and analyzing structures.

    • SFD and BMD can be used to determine the maximum shear force and bending moment...

  • Answered by AI
  • Q9. Tell me about yourself
  • Ans. 

    I am a recent engineering graduate with a passion for problem-solving and innovation.

    • Graduated with a degree in engineering

    • Strong problem-solving skills

    • Passionate about innovation and technology

    • Completed internships in the engineering field

    • Involved in extracurricular activities such as robotics club

  • Answered by AI
  • Q10. What are your hobbies?
  • Ans. 

    My hobbies include reading, playing sports, and traveling.

    • I enjoy reading books on various topics, including fiction, non-fiction, and biographies.

    • I like to play sports such as basketball, football, and cricket to stay active and healthy.

    • I love to travel and explore new places, cultures, and cuisines.

  • Answered by AI
  • Q11. What are your plans about future?
  • Ans. 

    I plan to gain experience and knowledge in my field while also pursuing further education.

    • I want to work for a reputable company in my field

    • I plan to attend conferences and workshops to stay up-to-date with industry advancements

    • I am considering pursuing a master's degree in the future

    • I hope to eventually take on leadership roles within my company or industry

  • Answered by AI
  • Q12. Are you willing to shift anywhere in India?
  • Ans. 

    Yes, I am willing to shift anywhere in India for the job.

    • I am open to exploring new places and cultures.

    • I understand that being a GET may require me to work in different locations.

    • I am willing to adapt to new environments and work with diverse teams.

    • For example, during my internship, I worked in a different city and enjoyed the experience.

    • I am excited about the opportunity to work with your company and contribute to it

  • Answered by AI
  • Q13. What would you do if you are not selected today?
  • Ans. 

    I would take it as a learning experience and try to improve my skills for future opportunities.

    • I would ask for feedback from the interviewer to understand my shortcomings

    • I would analyze my performance and identify areas of improvement

    • I would continue to apply for other opportunities and work on enhancing my skills

    • I would not let this rejection discourage me and stay positive for future prospects

  • Answered by AI

Interview Preparation Tips

Round: Test
Experience: This round was pretty easy. English section had questions regarding error detection, passage, jumbled sentences, antonyms and synonyms. Logical thinking had position of numbers on cube, flowchart based problem, coding-decoding, blood relations and direction questions. Logical had questions from time-work, speed-time-distance, simple interest, heights-distances and venn diagrams.
Tips: Practice R.S.Aggrawal and also try to solve questions from competition success reveiw (it helps)
Duration: 80 minutes
Total Questions: 90

Round: Group Activity
Experience: Our group discussion was on topic Social media: Boon or Bane for 10 minutes with additional 2 minutes for preparation.
Tips: Try to initiate the discussion, try to speak 4-5 valid points. And if you could not initiate then atleast try to conclude the discussion.

Round: Technical Interview
Experience: The interview lasted for about half-an hour and I answered all the questions
Tips: Be through with all the concepts. Concentrate more on concrete technology, Structural analysis, Mechanics and Geotechnical.

Round: HR Interview
Experience: The HR manager are very calm and I answered all the questions with confidence.
Tips: Be calm and answer honestly.

Skills: Mechanical Behavior Of Materials, Concrete Technology, Construction Project Management, Construction Management Skills, technical Knowledge
College Name: KLE Technological University

Interview Questionnaire 

4 Questions

  • Q1. WHY SHAPOORJI PALLONJI NT OTHER COMPANY
  • Q2. WHY DONT YOU PREFER HIGHER STUDIES
  • Q3. Tell me about your summer internship
  • Q4. Questions related to basic rac( vapour compression refrigeration cycle) ,theory of machine(gear,shaft),strength of materials(basic theory,types of beams etc

Interview Preparation Tips

Round: Resume Shortlist
Experience: Normally in spec(shapoorji pallonji engineering construction) ,they give maximum focus on career. The company make a list of names from college...you have minimum 80% in 10th and 12th . And u have minimum 8.5 cgpa in college
Tips: Be serious from the beginning of your 1st year

Round: Test
Experience: In written test, you have 2 papers. Technical and non-technical. In technical round you have i.c engine (major), theory of machine, strength of material, production, industrial, refrigeration and air conditioning etc. But don’t be afraid. The questions are very simple. You just need to overlook on the syllabus.  There will be 40 questions in 20 minutes ... So don’t expect numerical questions
.direct theory and formula based questions in non-technical paper you have 40 questions consists of only English .no apti or anything. If you are strong in vocab that is good...if not den it’s ok. Try to cover grammar part.as grammar has 10 marks weight-age.
Tips: I may suggest that if you are preparing for gate, any core company written you can easily crack.

Round: Group Discussion
Experience: Listen g.d will always be a fish market. Just have focus on the key words of the topic.ex, in my topic key words were Mr. Modi and infrastructure. One thing that this company doesn’t give more emphasis on g.d .you just need to speak.
Tips: Dont worry about g.d. simply this company checks whether you can at least speak in english or not.. G.d. is not an elimination round.

Round: HR Interview
Experience: 1st search that what are the scopes that any engineering construction company has for mechanical engineers... My answer was that for design of duct in air conditioning system, mechanical electrical plumbing,hvac system (heating,ventilating,and air conditioning) for all the above system any construction company needs a mechanical engineer. Another thing is that mechanical engineers are the back
bone of any core company. Wherever there is a machine, there will be a mechanical engineer.Another thing never tell them that you want higher studies. I answered," I have a rough idea related to technology during my 4 years course. Now I just want 2 explore that are the practical applications of those theoretical knowledge"
Tips: Have a brief idea about what is the company ,who are the key persons,foundation of company

Round: Technical Interview
Experience: The procedue is very simple.the questions are very simple.have maximum focus on your summer training. In my case out of total 40 minutes interview 30 minutes discussion was related to my project.. 10 minutes from theory of machine(gear,shaft),mechanics of material(types of beam) and last h.r interview.
Tips: Prepare for gate ..you will be having 100% confidence during your personal interview. And finally all the best for your future...any query you can stay in contact with me via facebook.

Skill Tips: If you are preparing for gate,you will surely get a core job...you can buy made easy hand book for short notes of all the btech course. It will also be helpful for your gate preparation a ..you can get it from nearest book stall or online.
College Name: KIIT UNIVERSITY

Jacobs Engineering Group Interview FAQs

How many rounds are there in Jacobs Engineering Group Electrical & Instrumentation Engineer interview?
Jacobs Engineering Group interview process usually has 1 rounds. The most common rounds in the Jacobs Engineering Group interview process are Technical.

Tell us how to improve this page.

Interview Questions from Similar Companies

L&T Construction Interview Questions
4.0
 • 758 Interviews
Saint-Gobain Interview Questions
4.0
 • 173 Interviews
Dilip Buildcon Interview Questions
4.0
 • 147 Interviews
G R Infraprojects Interview Questions
4.1
 • 134 Interviews
AECOM Interview Questions
4.2
 • 118 Interviews
Worley Interview Questions
4.1
 • 113 Interviews
View all
Design Engineer
276 salaries
unlock blur

₹4.5 L/yr - ₹18 L/yr

Senior Design Engineer
147 salaries
unlock blur

₹9 L/yr - ₹26 L/yr

Piping Design Engineer
101 salaries
unlock blur

₹4.7 L/yr - ₹15 L/yr

Piping Designer
88 salaries
unlock blur

₹3.4 L/yr - ₹12.8 L/yr

Senior Engineer
73 salaries
unlock blur

₹10 L/yr - ₹21 L/yr

Explore more salaries
Compare Jacobs Engineering Group with

L&T Construction

4.0
Compare

Megha Engineering & Infrastructures

3.9
Compare

Shapoorji Pallonji Group

4.1
Compare

Alstom Transportation

3.7
Compare
Did you find this page helpful?
Yes No
write
Share an Interview