Filter interviews by
I applied via Referral and was interviewed before Oct 2020. There were 3 interview rounds.
Asked basic mechanic engineering questions like Rankine cycle
Boil water, add tea leaves, steep for desired time, strain and serve with milk and sugar.
Boil water in a kettle or pot
Add tea leaves to a teapot or infuser
Pour hot water over tea leaves and steep for desired time
Strain tea into a cup and add milk and sugar to taste
I applied via Campus Placement
Basic Aptitude Test,Reasoning,Maths
posted on 15 Aug 2023
I applied via Walk-in and was interviewed before Aug 2022. There were 2 interview rounds.
33/11 kv pss refers to a 33kV/11kV primary substation working.
33/11 kv pss stands for a primary substation with a voltage level of 33kV/11kV.
It is responsible for stepping down the high voltage from the transmission line to a lower voltage suitable for distribution to consumers.
The substation includes equipment such as transformers, circuit breakers, and protection devices.
It plays a crucial role in ensuring reliable p...
I applied via Walk-in and was interviewed in Jul 2021. There was 1 interview round.
posted on 2 Jan 2024
I applied via Naukri.com and was interviewed in Dec 2023. There was 1 interview round.
posted on 9 Jan 2025
I applied via Walk-in and was interviewed in Jul 2024. There was 1 interview round.
OGT stands for Overall Gas Turbine. It is a measure of the overall performance of a gas turbine engine.
OGT is calculated by taking into account various parameters such as turbine inlet temperature, compressor discharge pressure, and fuel flow rate.
Monitoring OGT is crucial for ensuring the efficient operation of the gas turbine engine.
An increase in OGT may indicate a potential issue with the engine, such as fouling of...
Switch gear is a combination of electrical disconnect switches, fuses or circuit breakers used to control, protect and isolate electrical equipment.
Switch gear is used to control the flow of electricity in a power system.
It includes devices like circuit breakers, fuses, and disconnect switches.
Switch gear is essential for protecting electrical equipment from overloads and short circuits.
It helps in isolating faulty equ...
Transformer safety involves measures to prevent electrical hazards and ensure proper functioning of transformers.
Regular maintenance and inspection of transformers is essential for safety
Proper grounding and insulation to prevent electrical shocks
Following safety protocols and procedures when working with transformers
Using personal protective equipment (PPE) when handling transformers
Avoiding overloading transformers t
Chillers safety refers to the measures in place to ensure the safe operation of chillers and prevent accidents.
Regular maintenance and inspections are crucial for ensuring the safety of chillers.
Proper training of personnel on chiller operation and safety protocols is essential.
Emergency shutdown procedures should be clearly defined and easily accessible.
Safety features such as pressure relief valves and temperature se...
Control diagrams for Star Delta and DOL starters are essential for understanding the operation of these motor starting methods.
Control diagram for Star Delta starter involves two contactors and a timer for switching between star and delta connections.
Control diagram for DOL starter includes a single contactor for direct starting of the motor.
Both diagrams show the connections of the motor, contactors, overload relays, ...
I applied via Referral and was interviewed in Feb 2021. There was 1 interview round.
M-25 Grade concrete is a type of concrete with a compressive strength of 25 megapascals (MPa).
M-25 Grade concrete is commonly used in construction projects.
The ratio of M-25 Grade concrete is 1:1:2, which means 1 part cement, 1 part fine aggregate (sand), and 2 parts coarse aggregate (stone).
The mix proportion of M-25 Grade concrete is designed to achieve a desired strength and durability for the specific application.
F...
The number of bricks required in 1 cubic meter depends on the size of the bricks and the thickness of the mortar joints.
The size of the bricks and the thickness of the mortar joints determine the number of bricks needed.
Standard brick sizes are commonly used in construction.
For example, if the size of the brick is 200mm x 100mm x 75mm and the thickness of the mortar joint is 10mm, the calculation would be as follows:
- ...
I applied via Campus Placement
General aptitude, programing aptitude, logical and arithametic
Civil Site Engineer
23
salaries
| ₹0 L/yr - ₹0 L/yr |
Project Manager
17
salaries
| ₹0 L/yr - ₹0 L/yr |
Site Engineer
13
salaries
| ₹0 L/yr - ₹0 L/yr |
Project Engineer
11
salaries
| ₹0 L/yr - ₹0 L/yr |
Supply Executive
7
salaries
| ₹0 L/yr - ₹0 L/yr |
Urban Company
Qube Services
Taskbob
Zimmber