Bio Urja Interview Questions and Answers

General aptitude test (logical reasoning, quant. Aptitude )

Q1. Related to field.
Add your answer

Q1. Working of compressor & turbine
Ans. 
Compressors increase pressure of gases, while turbines convert fluid energy into mechanical work.
• Compressors are used in refrigeration and air conditioning systems to compress refrigerants.

• Turbines are commonly found in power plants, converting steam or gas energy into electricity.

• Positive displacement compressors (like reciprocating compressors) trap a fixed volume of gas and reduce its volume.

• Centrifugal compressors ...read more
Answered by AI
Add your answer
Q2. BFW pump working & maintenances
Add your answer

Q1. Experience and about your self
Add your answer

Over the Job discription

Q1. Package discussion and accommodation discussion
Add your answer

Q1. Where are you work and your present company.
Add your answer
Q2. Operation department in NGSL at jharsuguda site
Add your answer

Q1. What is main reason for belt joint failure?
Ans. 
The main reason for belt joint failure is usually due to improper installation or maintenance.
• Improper installation of the belt joint, such as incorrect alignment or tensioning

• Lack of proper maintenance, leading to wear and tear of the joint

• Use of low-quality materials for the joint

• Excessive load or stress on the belt joint

• Environmental factors like temperature or humidity affecting the joint
Answered by AI
Add your answer
Q2. What was the alignment maximum tolerance?
Ans. 
The alignment maximum tolerance refers to the maximum allowable deviation from the specified alignment.
• Alignment maximum tolerance is the maximum allowable deviation from the specified alignment.

• It is typically expressed in terms of a percentage or a specific measurement unit.

• For example, a machine part may have an alignment maximum tolerance of +/- 0.005 inches.

• Exceeding the alignment maximum tolerance can lead to per
Answered by AI
Add your answer
Q3. How to replace the bucket wheel reclaimer luffing cylinder?
Ans. 
To replace the bucket wheel reclaimer luffing cylinder, follow these steps.
• 1. Shut down the machine and ensure all power sources are disconnected.

• 2. Remove any surrounding components that may obstruct access to the luffing cylinder.

• 3. Use appropriate tools to disconnect the hydraulic hoses and fittings from the cylinder.

• 4. Support the weight of the cylinder as it is removed to prevent damage to surrounding components.

• 5...read more
Answered by AI
Add your answer
Q4. What is different between JSA and HIRA?
Ans. 
JSA stands for Job Safety Analysis, focusing on specific job tasks, while HIRA stands for Hazard Identification and Risk Assessment, focusing on overall workplace hazards.
• JSA is task-specific, focusing on individual job tasks and potential hazards

• HIRA is broader, looking at overall workplace hazards and assessing risks

• JSA involves breaking down a job into steps and identifying potential hazards for each step

• HIRA involv...read more
Answered by AI
Add your answer
Q5. How create a PR in SAP?
Ans. 
To create a PR in SAP, you can use transaction code ME51N or ME21N.
• Use transaction code ME51N to create a purchase requisition in SAP.

• Enter the necessary details such as material, quantity, delivery date, etc.

• Save the purchase requisition and it will be created in the system.

• Alternatively, you can also use transaction code ME21N to create a purchase order directly.
Answered by AI
Add your answer
Q6. What is procedure of pulley replacement?
Ans. 
The procedure of pulley replacement involves identifying the faulty pulley, removing the old pulley, installing the new pulley, and testing the system.
• Identify the faulty pulley by checking for any signs of wear or damage.

• Use appropriate tools to remove the old pulley, such as a pulley puller or wrench.

• Install the new pulley by aligning it properly and securing it in place.

• Test the system to ensure the new pulley is fu...read more
Answered by AI
Add your answer
Q7. Explain the procedure of PTW?
Ans. 
PTW stands for Permit to Work, a procedure used to ensure that work is carried out safely in potentially hazardous environments.
• PTW is a formal written system used to control certain types of work that are identified as potentially hazardous.

• Before starting work, a permit must be obtained from a designated authority.

• The permit outlines the work to be done, the hazards involved, and the necessary precautions to be taken...read more
Answered by AI
Add your answer