Amara Raja Infra Senior Quality Control Engineer Interview Questions, Process, and Tips

Q1. How did you hear about company
Ans. 
Through a job posting on LinkedIn
• Found job posting on LinkedIn

• Researched company after seeing job posting

• Connected with current employees on LinkedIn

• Received referral from a friend or colleague
Answered by AI
Add your answer
Q2. How many experience in high rise with contractor company
Ans. 
I have 8 years of experience working on high rise projects with contractor companies.
• I have worked on multiple high rise projects ranging from 20 to 50 stories.

• Managed structural design and construction of high rise buildings.

• Collaborated with architects, contractors, and clients to ensure project success.
Answered by AI
Add your answer

Asking about Experience like structure, finishing.
What is testing of Steel IS CODE
BILLING OF IS CODE
BBS IS CODE.
CMD IS CODE.

SAFETY HAZARD ANALYSIS.
CONSTRUCTION METHOD STATEMENT.

TYPES OF PLASTER
OUTER PLASTER THICKNESS.
INNER PLASTER THICKNESS.

Q1. About Quality management system
Add your answer
Q2. Health Safety & Environment
Add your answer
Q3. About Standard, Procedure & Specification
Add your answer
Q4. Internal & External Audit
Add your answer

Q1. Define SFD ,BMD
Ans. 
SFD stands for Shear Force Diagram and BMD stands for Bending Moment Diagram in structural analysis.
• SFD shows the variation of shear force along the length of a beam or structure.

• BMD shows the variation of bending moment along the length of a beam or structure.

• Both diagrams are essential for analyzing the internal forces in a structure.

• They are commonly used in civil and mechanical engineering for designing and analyzi...read more
Answered by AI
Add your answer
Q2. Calculate Thrust forces for beam
Ans. 
Thrust forces for beams can be calculated using equations of equilibrium and considering external loads.
• Calculate the sum of all external forces acting on the beam.

• Determine the direction of the forces (compression or tension) based on the beam's support conditions.

• Apply equations of equilibrium to calculate the thrust forces at different points along the beam.

• Consider any distributed loads or moments that may affect t...read more
Answered by AI
Add your answer

Software or tool test

Q1. Related to technical question about fabrication.
Add your answer
Q2. Tool related question
Add your answer

Q1. What is blinding? Different types of blinds used in o&g?
Ans. 
Blinding is the process of isolating a section of a pipeline or equipment to prevent flow or contamination.
• Temporary or permanent blinds can be used depending on the situation

• Common types of blinds include spectacle blinds, paddle blinds, and bleed rings

• Blinding is often used during maintenance or repair work to ensure safety

• Blinding can also be used to prevent contamination during storage or transportation

• Blinding can...read more
Answered by AI
Add your answer
Q2. Procedures before starting a work in a refinery equipment,
Ans. 
Before starting work in a refinery equipment, certain procedures must be followed.
• Obtain a work permit

• Perform a safety check of the equipment

• Ensure proper personal protective equipment is worn

• Verify that all valves are in the correct position

• Confirm that the equipment is properly grounded

• Check for any leaks or abnormal conditions

• Communicate with other workers in the area

• Follow all established procedures and protocols
Answered by AI
Add your answer
Q3. What will you do if there's an H2S leak and there's no wind movement,
Ans. 
I will follow the emergency response plan and evacuate the area immediately.
• Activate the alarm system to alert others in the area

• Put on personal protective equipment (PPE) including a respirator

• Evacuate the area immediately and move to a safe location

• Notify emergency services and follow the emergency response plan

• Monitor the situation and wait for the all-clear signal before returning to the area
Answered by AI
Add your answer
Q4. From where you'll advice your workers to start unbloting a heat exchanger head?
Ans. 
I would advise my workers to start unbolting the heat exchanger head from the top and work their way down.
• Start from the top and work your way down

• Use appropriate tools and safety equipment

• Follow proper procedures and guidelines

• Ensure all bolts are properly labeled and accounted for

• Inspect the gasket and replace if necessary
Answered by AI
Add your answer

Q1. Why you joined Keller?
Add your answer
Q2. Are you comfortable with any location?
Add your answer
Q3. Tell me work details?
Add your answer
Q4. Are you preparing a method statement?
Ans. 
Yes, I am preparing a method statement for the project.
• Yes, I am currently working on preparing a method statement for the project.

• I am in the process of outlining the steps and procedures to be followed in the project.

• The method statement will include details on quality control measures, testing procedures, and documentation requirements.
Answered by AI
Add your answer
Q5. Are you prepare a PQP?
Ans. 
Yes, I am able to prepare a PQP (Product Quality Plan).
• I have experience in creating detailed PQPs outlining quality control processes and procedures.

• I ensure that the PQP meets all relevant industry standards and regulations.

• I collaborate with cross-functional teams to gather input and ensure alignment on quality goals.

• I regularly review and update the PQP to reflect any changes in processes or requirements.
Answered by AI
Add your answer

Q1. Tell me about yourself
Add your answer
Q2. Why you want to leave your current organisation
Add your answer
Q3. Are you comfortable to frequent site changes and travel
Add your answer
Q4. What is your salary expection
Add your answer