Upload Button Icon Add office photos

Filter interviews by

Tube Investments of India Project Engineer Interview Questions and Answers

Updated 4 Jun 2024

Tube Investments of India Project Engineer Interview Experiences

1 interview found

Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
4-6 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed in Dec 2023. There were 4 interview rounds.

Round 1 - Aptitude Test 

Easy to Moderate Level Questions

Round 2 - Technical 

(1 Question)

  • Q1. Medium to Difficult and Numerical Question
Round 3 - One-on-one 

(1 Question)

  • Q1. Technical Question From Qualification and Resume Based
Round 4 - HR 

(1 Question)

  • Q1. Introduction, Some General Knowledge

Interview questions from similar companies

Interview experience
5
Excellent
Difficulty level
Easy
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Company Website and was interviewed in Jun 2024. There was 1 interview round.

Round 1 - Technical 

(2 Questions)

  • Q1. About your work define self.
  • Q2. Pile, Girder and Major bridge related.
Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - One-on-one 

(3 Questions)

  • Q1. Asked technical questions
  • Q2. What is the bulk modulus
  • Ans. 

    Bulk modulus is a measure of a material's resistance to compression under pressure.

    • It is a measure of a material's compressibility

    • It is defined as the ratio of change in pressure to the fractional volume compression

    • It is used in the study of elasticity and fluid mechanics

    • Examples of materials with high bulk modulus include diamond and steel

    • Examples of materials with low bulk modulus include rubber and foam

  • Answered by AI
  • Q3. Why there is G constant during bulling of sand
  • Ans. 

    G constant is required during sand bulking to account for the change in volume due to the presence of air voids.

    • G constant is used to calculate the volume of sand when it is in a loose state.

    • The presence of air voids in sand causes it to increase in volume, which is known as bulking.

    • The amount of bulking depends on the moisture content and the type of sand.

    • G constant is determined experimentally by comparing the volume...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Offer ketter was received after 3 months, lost all hopes during thse three montha so started searching for another job and got selected in foreign

I applied via LinkedIn and was interviewed in Aug 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Tell us how would you behave in a difficult situation with a client
  • Q2. Why do you want to work with us

Interview Preparation Tips

Interview preparation tips for other job seekers - Study the questions prior the interview. Relax ad think before questions

I applied via Job Portal and was interviewed in Nov 2021. There were 3 interview rounds.

Interview Questionnaire 

5 Questions

  • Q1. Structure related pile foundation
  • Q2. Pile testing ,girder stressing
  • Q3. How much miller required for 500 cum concrete transporting
  • Ans. 

    The amount of miller required for transporting 500 cum concrete depends on various factors.

    • The type of miller being used

    • The distance the concrete needs to be transported

    • The size of the project

    • The time frame for completing the project

    • The availability of resources

    • The budget allocated for the project

  • Answered by AI
  • Q4. Girder launching
  • Q5. Box underpasses

Interview Preparation Tips

Interview preparation tips for other job seekers - Give only answer to the point which is no you

Interview Questionnaire 

1 Question

  • Q1. They asked about previous experience and they asked me what’ are piling activities you followed let me explain that’s it

Interview Preparation Tips

Interview preparation tips for other job seekers - Share about your knowledge of work experience with confidently

I applied via Company Website and was interviewed in Oct 2020. There were 4 interview rounds.

Interview Questionnaire 

13 Questions

  • Q1. What your experience
  • Q2. Crust thickness
  • Q3. How to cut 150 hill in 60 degree slope
  • Ans. 

    Cutting 150 hill in 60 degree slope requires careful planning and execution.

    • Conduct a thorough survey of the area to determine the best approach

    • Use heavy machinery such as excavators and bulldozers to remove the hill

    • Ensure safety measures are in place to prevent accidents

    • Consider environmental impact and take necessary precautions

    • Consult with experts in the field for advice and guidance

  • Answered by AI
  • Q4. How we do Protection in 150m height
  • Ans. 

    Protection in 150m height can be achieved through various means.

    • Use of safety harness and fall protection equipment

    • Installation of guardrails and safety nets

    • Implementation of a comprehensive safety plan

    • Regular inspection and maintenance of equipment

    • Training and education of workers on safety procedures

  • Answered by AI
  • Q5. Which grade of bitumin used in hill area
  • Ans. 

    The grade of bitumen used in hill areas depends on the temperature and altitude of the region.

    • The higher the altitude, the harder the bitumen used.

    • The temperature also plays a crucial role in determining the grade of bitumen.

    • For example, in colder regions, a harder grade of bitumen is used to prevent cracking and deformation.

    • In contrast, in warmer regions, a softer grade of bitumen is used to prevent rutting and deform

  • Answered by AI
  • Q6. How do we concrete in min temp
  • Ans. 

    Concrete in minimum temperature requires proper mix design, curing, and protection from freezing.

    • Use a mix design with low water-cement ratio and proper amount of cement and admixtures.

    • Ensure proper curing by covering the concrete with blankets or insulating materials.

    • Protect the concrete from freezing by using heaters or insulating blankets.

    • Monitor the temperature of the concrete and the environment during and after p...

  • Answered by AI
  • Q7. How do we protect cavity in tunnel
  • Ans. 

    Cavity in tunnels can be protected by using various methods.

    • Waterproofing the tunnel lining

    • Using grouting techniques to fill the cavity

    • Installing drainage systems to prevent water accumulation

    • Regular inspections and maintenance

    • Using shotcrete to reinforce the tunnel lining

    • Applying rock bolts to stabilize the surrounding rock

    • Using steel ribs to support the tunnel lining

  • Answered by AI
  • Q8. Cycle time in tunnel
  • Ans. 

    Cycle time in tunnel refers to the time taken to complete one cycle of a process or operation within the tunnel.

    • Cycle time can vary depending on the type of tunnel and the process being carried out.

    • For example, in a transportation tunnel, cycle time may refer to the time taken for a vehicle to enter and exit the tunnel.

    • In a manufacturing tunnel, cycle time may refer to the time taken to complete one production cycle.

    • Ef...

  • Answered by AI
  • Q9. NATM full form
  • Ans. 

    NATM stands for New Austrian Tunneling Method, a technique used in underground construction.

    • NATM is a tunneling method that involves excavating the tunnel while providing support to the surrounding rock mass.

    • It was developed in Austria in the 1950s and has since been used in various tunneling projects worldwide.

    • NATM involves the use of shotcrete, rock bolts, and steel ribs to support the tunnel walls and roof.

    • Examples ...

  • Answered by AI
  • Q10. How much we drill holes in face
  • Ans. 

    The frequency of drilling holes in the face depends on the specific project requirements and geological conditions.

    • The number of holes drilled in the face will vary depending on the project's needs and the geological conditions of the site.

    • Factors such as the type of rock, the size of the excavation, and the equipment being used will all influence the frequency of drilling.

    • It is important to carefully plan and execute ...

  • Answered by AI
  • Q11. What is proholes and what it's uses
  • Ans. 

    Proholes is not a known term in engineering. No data available.

    • Answered by AI
    • Q12. Why is drain holes we do
    • Ans. 

      Drain holes are necessary to prevent water accumulation and damage to structures or equipment.

      • Drain holes allow water to escape from areas where it can cause damage or corrosion.

      • They are commonly used in outdoor furniture, boats, and buildings to prevent water accumulation.

      • Drain holes can also be used in machinery to prevent damage from water or other liquids.

      • Proper placement and size of drain holes is important to ens

    • Answered by AI
    • Q13. How much asscelerate we used in shotcrete
    • Ans. 

      The amount of accelerator used in shotcrete depends on various factors.

      • The type of accelerator used affects the amount required.

      • The desired strength and setting time also play a role.

      • The ambient temperature and humidity can affect the amount needed.

      • Typically, 1-5% of the cement weight is used as accelerator.

      • The manufacturer's recommendations should be followed for best results.

    • Answered by AI

    Interview Preparation Tips

    Interview preparation tips for other job seekers - Be confident always think and speake
    Interview experience
    3
    Average
    Difficulty level
    -
    Process Duration
    -
    Result
    -
    Round 1 - HR 

    (2 Questions)

    • Q1. Tell us about yourself
    • Q2. What's your strengths
    Interview experience
    4
    Good
    Difficulty level
    -
    Process Duration
    -
    Result
    -
    Round 1 - Technical 

    (2 Questions)

    • Q1. Outer dia of HDPE pipe and specifications
    • Ans. 

      The outer diameter of HDPE pipe varies based on the intended use and specifications.

      • HDPE pipes are available in a range of sizes from 16mm to 2000mm.

      • The outer diameter of HDPE pipe is typically larger than the inner diameter.

      • The thickness of the pipe wall also varies based on the intended use and pressure requirements.

      • HDPE pipes are commonly used for water supply, gas distribution, and sewage systems.

    • Answered by AI
    • Q2. Work process how to handle contractor and local people how to exicute SOP
    • Ans. 

      To handle contractors and local people, we follow a structured process and execute SOPs.

      • We establish clear communication channels with contractors and local people.

      • We ensure that all parties understand the project goals and objectives.

      • We provide training and support to contractors and local people on the SOPs.

      • We monitor and evaluate the performance of contractors and local people regularly.

      • We address any issues or conc...

    • Answered by AI

    Interview Preparation Tips

    Interview preparation tips for other job seekers - Be confident

    I applied via Naukri.com and was interviewed before May 2021. There were 3 interview rounds.

    Round 1 - Resume Shortlist 
    Pro Tip by AmbitionBox:
    Properly align and format text in your resume. A recruiter will have to spend more time reading poorly aligned text, leading to high chances of rejection.
    View all tips
    Round 2 - HR 

    (1 Question)

    • Q1. Technical experience and Salary related Questions
    Round 3 - Technical 

    (1 Question)

    • Q1. Technical experience Questions with AVP Sir

    Interview Preparation Tips

    Interview preparation tips for other job seekers - You have stay with confidence and Working Style

    Tube Investments of India Interview FAQs

    How many rounds are there in Tube Investments of India Project Engineer interview?
    Tube Investments of India interview process usually has 4 rounds. The most common rounds in the Tube Investments of India interview process are Aptitude Test, Technical and One-on-one Round.
    How to prepare for Tube Investments of India Project Engineer interview?
    Go through your CV in detail and study all the technologies mentioned in your CV. Prepare at least two technologies or languages in depth if you are appearing for a technical interview at Tube Investments of India. The most common topics and skills that interviewers at Tube Investments of India expect are Quality Control, Building Construction, CNC, Commissioning and Communication Skills.
    What are the top questions asked in Tube Investments of India Project Engineer interview?

    Some of the top questions asked at the Tube Investments of India Project Engineer interview -

    1. Technical Question From Qualification and Resume Ba...read more
    2. Medium to Difficult and Numerical Quest...read more
    3. Introduction, Some General Knowle...read more

    Tell us how to improve this page.

    Tube Investments of India Project Engineer Interview Process

    based on 2 interviews

    Interview experience

    4.5
      
    Good
    View more
    Tube Investments of India Project Engineer Salary
    based on 58 salaries
    ₹3 L/yr - ₹6 L/yr
    17% less than the average Project Engineer Salary in India
    View more details

    Tube Investments of India Project Engineer Reviews and Ratings

    based on 8 reviews

    4.3/5

    Rating in categories

    4.3

    Skill development

    3.5

    Work-life balance

    3.9

    Salary

    4.7

    Job security

    3.6

    Company culture

    3.6

    Promotions

    3.5

    Work satisfaction

    Explore 8 Reviews and Ratings
    Assistant Manager
    134 salaries
    unlock blur

    ₹3.5 L/yr - ₹13.4 L/yr

    Senior Executive
    122 salaries
    unlock blur

    ₹4.3 L/yr - ₹9.8 L/yr

    Quality Inspector
    81 salaries
    unlock blur

    ₹1 L/yr - ₹3.5 L/yr

    Quality Engineer
    71 salaries
    unlock blur

    ₹1.4 L/yr - ₹4.5 L/yr

    Senior Engineer
    65 salaries
    unlock blur

    ₹2.5 L/yr - ₹6.3 L/yr

    Explore more salaries
    Compare Tube Investments of India with

    Bharat Forge

    3.9
    Compare

    Mahindra & Mahindra

    4.1
    Compare

    Tata Steel

    4.1
    Compare

    JSW Steel

    3.9
    Compare
    Did you find this page helpful?
    Yes No
    write
    Share an Interview