Threyes Srinisons Harness Pvt,ltd Interview Questions, Process, and Tips

I have a valid driver's license for both cars and motorcycles.

• I have a Class C license for cars

• I also have a Class M license for motorcycles

• I have a clean driving record with no accidents or violations

I ride a road bike for commuting and a mountain bike for leisure.

• I prefer road bikes for their speed and efficiency on paved roads.

• I enjoy mountain biking for the challenge and adventure of off-road trails.

• I also have experience with hybrid bikes for their versatility.

• I prioritize safety and always wear a helmet and follow traffic laws.

• I have participated in charity rides and group rides for fun and community.

Vehicle testing involves various methods to ensure safety, performance, and compliance with regulations.

• Testing can include physical tests such as crash tests, durability tests, and performance tests.

• Simulation and modeling can also be used to test vehicle components and systems.

• Testing must comply with regulations set by organizations such as the National Highway Traffic Safety Administration (NHTSA) and the European

We conduct various types of homologation testing depending on the product and its intended market.

• We conduct safety testing to ensure compliance with local regulations.

• We perform emissions testing to ensure compliance with environmental regulations.

• We conduct performance testing to ensure the product meets the required standards.

• We also conduct durability testing to ensure the product can withstand the expected wear an...read more

I faced a defect in plastic commodity related to poor quality control during the manufacturing process.

• The defect was in the form of cracks and breakages in the plastic products.

• It was caused by inadequate monitoring and supervision during the molding and cooling stages.

• The defect resulted in a high number of rejected products and customer complaints.

• To address the issue, we implemented stricter quality control measure...read more

Improving quality requires a focus on continuous improvement and attention to detail.

• Establish clear quality standards and metrics

• Regularly review and analyze data to identify areas for improvement

• Implement processes and procedures to address identified issues

• Provide training and support to employees to ensure they understand and can meet quality standards

• Encourage a culture of continuous improvement and innovation

The types of lacquer used on lens and housing include acrylic lacquer, polyurethane lacquer, and epoxy lacquer.

• Acrylic lacquer is commonly used on lens and housing due to its high transparency and UV resistance.

• Polyurethane lacquer provides excellent durability and chemical resistance, making it suitable for lens and housing.

• Epoxy lacquer offers superior adhesion and impact resistance, making it a preferred choice for

A size fine filter is a type of filter used to remove small particles or impurities from a fluid or gas.

• Size fine filters are commonly used in industries such as manufacturing, pharmaceuticals, and food processing.

• They are designed to capture particles that are smaller than what can be filtered by regular filters.

• These filters can be made of various materials such as paper, fabric, or synthetic fibers.

• Examples of size ...read more

Direct metalizing is applicable on materials that can conduct electricity.

• Direct metalizing is a process of coating a non-metallic surface with a thin layer of metal.

• The material should be able to conduct electricity for direct metalizing to be applicable.

• Materials like plastic, glass, and ceramics can be direct metalized.

• Direct metalizing is commonly used in the automotive, aerospace, and electronics industries.

The amount of UV energy required for curing depends on the type of material being cured and the intensity of the UV light.

• UV energy required for curing varies depending on the material being cured

• Intensity of the UV light also affects the amount of energy required

• UV energy is typically measured in Joules per square centimeter (J/cm²)

• Examples of materials that require UV curing include adhesives, coatings, and inks

The amount of DFT required as per standard varies depending on the specific industry and project requirements.

• The required amount of DFT (Design for Testability) is determined by industry standards and project specifications.

• Different industries may have different standards for DFT.

• The complexity and size of the project also influence the amount of DFT required.

• DFT techniques include scan chains, built-in self-test (BI...read more

I have achieved several milestones throughout my career as a Senior Engineer.

• Successfully led a team of engineers to develop and implement a new software system, resulting in a 20% increase in efficiency.

• Received recognition for designing and implementing a cost-effective solution that reduced production downtime by 30%.

• Contributed to the development of a groundbreaking technology that revolutionized the industry, lead...read more

Die casting and machining defects are common in manufacturing processes.

• Die casting defects include porosity, shrinkage, cold shuts, and flash.

• Machining defects include burrs, chatter marks, and tool marks.

• Die casting defects can be caused by improper temperature, pressure, or metal flow.

• Machining defects can be caused by dull tools, improper speeds and feeds, or poor fixturing.

• Defects can lead to part failure, reduced

Filling and high speed ratio formula is used to calculate the filling time of a container with a specific volume of liquid at a given flow rate.

• Filling and high speed ratio formula is V/Q

• V is the volume of the container and Q is the flow rate of the liquid

• The formula is used to determine the time it takes to fill a container with a specific volume of liquid at a given flow rate

• The higher the flow rate, the faster the c