Steel Strips Wheels Graduate Engineer Trainee (Get) Interview Questions and Answers for Freshers

Q1. No question asked direct joining
Add your answer
Q2. Do u know about our company
Ans. 
The company is not specified.
Answered by AI
Add your answer
Q3. Give introduction briefly about yourself
Ans. 
I am a recent engineering graduate with a passion for problem-solving and innovation.
• I recently graduated with a degree in engineering from XYZ University

• During my time at university, I was involved in several extracurricular activities such as robotics club and volunteering at local STEM events

• I have completed internships at ABC Company and DEF Corporation, where I gained experience in project management and design

• I a...read more
Answered by AI
Add your answer

Q1. Self your introduction
Add your answer
Q2. Electrical vehicles, what is chassis
Add your answer
Q3. What is automobile, what is otto ,dual,diesels cycle difference
Ans. 
The question is about the basics of automobile engines and the differences between Otto, Dual, and Diesel cycles.
• Automobile is a vehicle powered by an engine that converts fuel into mechanical energy.

• Otto cycle is a four-stroke combustion cycle used in gasoline engines.

• Dual cycle is a modified version of the Otto cycle that includes a constant volume heat addition process.

• Diesel cycle is a four-stroke combustion cycle ...read more
Answered by AI
Add your answer
Q4. What is coefficient of performance input/output
Ans. 
Coefficient of performance (COP) is the ratio of output heat to input work or energy.
• COP is used to measure the efficiency of a heat pump or refrigeration system.

• It is calculated by dividing the output heat by the input work or energy.

• A higher COP indicates a more efficient system.

• For example, a heat pump with a COP of 3 can produce three units of heat for every unit of energy input.

• COP can also be expressed in terms o...read more
Answered by AI
Add your answer
Q5. How the otto cycle constants volume this process,
Ans. 
The Otto cycle is a constant volume process used in internal combustion engines.
• The Otto cycle consists of four processes: intake, compression, combustion, and exhaust.

• During the intake process, the fuel-air mixture is drawn into the cylinder.

• During the compression process, the mixture is compressed to a smaller volume, increasing its temperature and pressure.

• During the combustion process, the mixture is ignited, causi...read more
Answered by AI
Add your answer
Q6. What is the Duel cycle principles -both constant volume, and pressure
Ans. 
Dual cycle principles involve both constant volume and pressure processes in an engine cycle.
• Dual cycle is a combination of Otto and Diesel cycles.

• It involves two constant volume and one constant pressure processes.

• The first constant volume process is isentropic compression.

• The constant pressure process is combustion.

• The second constant volume process is isentropic expansion.

• It is used in gas turbine engines and some i
Answered by AI
Add your answer
Q7. Physical quantities length ,mass time
Add your answer
Q8. Efficiency of carnot T1/T2-T1
Ans. 
Efficiency of Carnot cycle is given by T1/T2-T1
• Efficiency of Carnot cycle is the maximum possible efficiency of a heat engine

• It depends only on the temperatures of the hot and cold reservoirs

• Efficiency = 1 - (T1/T2)

• T1 is the temperature of the cold reservoir and T2 is the temperature of the hot reservoir
Answered by AI
Add your answer

The aptitude test containing 80 questions which is MCQ type of questions and there is no any negative marking the timing for the test is 30 minutes. Aptitude is not very difficult but the category of the questions is good which we have to do very fast within the time to getting the maximum marks .

Q1. Here, the technical questions will ask in this round. What is your favourite subject in which subject you feel completely comfortable. They asking the some basic questions and some good question because th...read more
Add your answer
Q2. Q: 1 What is IC engine? What is the types of IC engine? Q:2 Difference between Otto cycle and Diesel cycle? What is the process of both cycle and what is the effeciency of both cycle ? Which one is good in...read more
Ans. 
Technical interview questions on IC engines, machining operations, welding, casting, heat treatment, thermodynamics, materials, and mechanics.
• IC engine types include spark ignition (SI) and compression ignition (CI)

• Otto cycle is used in SI engines while Diesel cycle is used in CI engines

• Welding types include MIG, TIG, and stick welding

• Casting types include sand casting, investment casting, and die casting

• Heat treatment...read more
Answered by AI
View 1 more answer

Q1. Here, the non- technical questions will ask. Regarding your strength, weakness, quality skills and your hobby. Generally, the question is easy but good. We have to give our good introduction.
Add your answer
Q2. Q:1 What is your name? Where do you live? Q:2 Tell me something about your self? Introduction. Q:3 What is your skills? What is your hobby? Q:4 Under this circumstances what will you do ? Q:5 Tell me some...read more
View 1 more answer