Filter interviews by
ITP stands for Inspection Test Plan and MOS stands for Method of Statement.
ITP is a document that outlines the inspection and testing procedures for a specific project or task.
MOS is a document that outlines the method or procedure for carrying out a specific task or activity.
Both ITP and MOS are important in ensuring quality control and compliance with standards and regulations.
I applied via Recruitment Consulltant and was interviewed in May 2023. There were 3 interview rounds.
Asking about isometric drawing
There are several types of flanges used in pipe fabrication.
Weld Neck Flange
Slip-On Flange
Socket Weld Flange
Threaded Flange
Blind Flange
Lap Joint Flange
To fit up a valve, follow these steps: measure and mark the pipe, cut the pipe, deburr the edges, clean the pipe and valve, apply pipe dope or Teflon tape to the threads, align the valve with the pipe, tighten the valve onto the pipe using a wrench.
Measure and mark the pipe where the valve will be installed
Cut the pipe using a pipe cutter or saw
Deburr the edges of the pipe to remove any sharp or rough edges
Clean the pi...
Pipe schedule refers to the thickness of a pipe wall and is used to determine the pressure capacity and strength of the pipe.
Pipe schedule is a standardized system used to classify the thickness of pipes.
It is denoted by a number followed by the letter 'S', such as Schedule 40 or Schedule 80.
The higher the schedule number, the thicker the pipe wall and the higher the pressure capacity.
Pipe schedule is important in indu...
Related of job, so I explained everything
SSEM interview questions for popular designations
I applied via Naukri.com and was interviewed in Sep 2022. There were 2 interview rounds.
I applied via Naukri.com and was interviewed before Nov 2022. There were 2 interview rounds.
To use materials effectively, it is important to understand their properties and applications. Building a strong team involves clear communication, delegation of tasks, and fostering a positive work environment.
Understand the properties and applications of different materials to use them effectively in piping projects.
Communicate clearly with team members to ensure everyone is on the same page.
Delegate tasks based on i...
Reading isometric drawings for fabrication involves understanding the symbols, dimensions, and orientation of the piping system.
Understand the scale of the drawing to accurately interpret dimensions.
Identify the symbols used for different components such as valves, fittings, and pipes.
Pay attention to the orientation of the piping system to ensure correct installation.
Follow the flow direction indicated in the drawing ...
I applied via Walk-in and was interviewed before Nov 2022. There were 2 interview rounds.
Reading isometric drawings involves understanding the 3D representation of piping systems. Fitting-up spool fabrication process requires precision and accuracy.
To read isometric drawings, understand the symbols and dimensions used to represent piping systems in 3D.
For fitting-up spool fabrication process, ensure accurate measurements and alignment of pipes for welding.
To find gaskets, refer to the piping specifications...
To find all fittings, experience with oil and gas lines, and working on refinery projects is essential for a pipe fitter.
Use blueprints and schematics to locate all fittings in a piping system
Experience with oil and gas lines helps in understanding the specific requirements and safety measures for these systems
Working on refinery projects requires knowledge of industry standards, regulations, and safety protocols
Hands-...
To control hazards and quality, proper training, regular inspections, and following safety protocols are essential.
Provide thorough training to all employees on safety procedures and protocols
Conduct regular inspections of equipment and work areas to identify and address potential hazards
Implement quality control measures to ensure work meets industry standards
Use appropriate personal protective equipment (PPE) at all ...
I applied via LinkedIn and was interviewed in Mar 2022. There were 2 interview rounds.
I applied via Company Website and was interviewed before Sep 2020. There was 1 interview round.
Top trending discussions
Some of the top questions asked at the SSEM interview -
based on 9 interviews
Interview experience
Electrical Engineer
9
salaries
| ₹0 L/yr - ₹0 L/yr |
Mechanical Engineer
8
salaries
| ₹0 L/yr - ₹0 L/yr |
HSE Officer
7
salaries
| ₹0 L/yr - ₹0 L/yr |
Safety Engineer
6
salaries
| ₹0 L/yr - ₹0 L/yr |
Civil Engineer
6
salaries
| ₹0 L/yr - ₹0 L/yr |
TCS
Infosys
Wipro
HCLTech