Filter interviews by
To detect stave cooling water leakage, various methods can be used such as visual inspection, pressure testing, temperature monitoring, and dye testing.
Perform regular visual inspections of the stave cooling system to check for any visible signs of leakage such as water stains or wet spots.
Conduct pressure testing by isolating sections of the cooling system and applying pressure to detect any drop in pressure, indicati...
The make of the 50/15 ton crane is not specified in the question.
The question does not provide information about the make of the crane.
It is important to know the make of the crane for maintenance and repair purposes.
Different makes of cranes may have different specifications and capabilities.
Examples of crane makes include Liebherr, Konecranes, and Demag.
The BF gas flow depends on various factors such as the size of the blast furnace, the type of fuel used, and the production rate.
BF gas flow is measured in cubic meters per hour (m3/h)
The flow rate can range from 1,000 to 10,000 m3/h depending on the size of the blast furnace
The type of fuel used can also affect the BF gas flow. For example, coke produces more gas than coal
The production rate of the blast furnace also ...
The type and capacity of the blast furnace depend on the specific requirements of the operation.
The type of blast furnace can vary based on factors such as the type of fuel used, the desired output, and the available resources.
Common types of blast furnaces include coke-fired, charcoal-fired, and electric arc furnaces.
Capacity can range from small-scale furnaces used for research and development to large-scale industri...
Blower capacity and type of bearing used in mono block are important factors for efficient blast furnace operation.
Blower capacity determines the amount of air required for combustion in the blast furnace.
Mono block bearings are used in blowers due to their high load carrying capacity and low maintenance requirements.
Roller bearings are commonly used in mono block bearings due to their ability to handle heavy loads and...
The type of oil used in power pack and gearbox depends on the specific requirements of the equipment.
The oil used in power pack and gearbox should have good lubrication properties to reduce friction and wear.
The oil should also have good thermal stability to withstand high temperatures.
The viscosity of the oil should be appropriate for the equipment and operating conditions.
Examples of oils used in power pack and gearb...
The cylinder size for lower and upper bell depends on the blast furnace size and production requirements.
The size of the cylinder should be chosen based on the blast furnace size and production requirements.
A larger cylinder can increase production but may require more energy and maintenance.
The material of the cylinder should also be considered for durability and heat resistance.
Consult with experts and follow industr...
Top trending discussions
I applied via Naukri.com and was interviewed before Apr 2020. There were 3 interview rounds.
Handling loss of RMHS materials involves proper inventory management, tracking systems, and security measures.
Implement a robust inventory management system to track all RMHS materials
Regularly conduct audits to ensure accuracy of inventory records
Utilize security measures such as surveillance cameras, access control systems, and restricted access areas
Train staff on proper handling and storage procedures to prevent lo...
Some electrical project ideas for in house improvements include installing smart home technology, upgrading lighting fixtures, and adding solar panels.
Install smart home technology for energy efficiency and convenience
Upgrade lighting fixtures to improve aesthetics and energy efficiency
Add solar panels to reduce electricity costs and environmental impact
Sap pm and electrically
I applied via Referral and was interviewed before Apr 2021. There were 2 interview rounds.
Design steps refer to the process of creating a plan or blueprint for a product or system.
Identifying the problem or need
Researching and gathering information
Brainstorming and generating ideas
Creating sketches or prototypes
Testing and evaluating the design
Refining and finalizing the design
Implementing and producing the final product
I will analyze the process flow, identify repetitive tasks, and implement automation tools to streamline the process.
Analyze the current process flow
Identify repetitive tasks that can be automated
Select appropriate automation tools
Implement automation tools and test thoroughly
Monitor and optimize the automated process
I applied via Referral and was interviewed before Sep 2023. There were 2 interview rounds.
I worked at XYZ Company as a software engineer for 3 years.
Developed new features for the company's flagship product
Collaborated with cross-functional teams to troubleshoot and resolve technical issues
Participated in code reviews and provided feedback to team members
Salary in previous company was competitive with industry standards.
Competitive with industry standards
Included benefits such as health insurance and retirement plans
Varied based on position and experience level
posted on 2 Jan 2024
I applied via Walk-in and was interviewed before Jan 2023. There was 1 interview round.
Aliment of DRI project
Loco car & charging car axle change in breakdowns involves replacing damaged axles to ensure proper functioning of the vehicles.
Loco car axle change is necessary when the axle is damaged due to wear and tear or accidents.
Charging car axle change is required to maintain the stability and safety of the vehicle.
Proper maintenance and regular inspections can help prevent breakdowns related to axle issues.
Examples: Replacin...
Thermo-Mechanically Treated
TMT stands for Thermo-Mechanically Treated
It is a process of treating steel bars to enhance their strength and durability
TMT bars are commonly used in construction for reinforcement
Thermo mechanically treated refers to a process where a material is subjected to both thermal and mechanical treatments to improve its properties.
Thermo mechanically treated materials undergo controlled heating and mechanical deformation to enhance their strength and toughness.
This process is commonly used in the manufacturing of high-strength steel for structural applications.
The combination of thermal and mechanical ...
Engineer
92
salaries
| ₹1.8 L/yr - ₹5 L/yr |
Senior Engineer
80
salaries
| ₹2.7 L/yr - ₹7 L/yr |
Executive
34
salaries
| ₹4 L/yr - ₹8.4 L/yr |
Deputy Manager
32
salaries
| ₹5 L/yr - ₹12 L/yr |
Junior Engineer
29
salaries
| ₹2 L/yr - ₹5 L/yr |
SHYAM METALICS AND ENERGY
Jai Balaji Group
Electrotherm
Welspun Corp