Senvion Electrical Engineer Interview Questions, Process, and Tips

Q1. Taranformer rating ....... KVA MVA HZ
Add your answer
Q2. Ohm low ...........
Add your answer
Q3. Current of unit .......
Ans. 
The question is asking about the current of a unit.
• The current of a unit refers to the amount of electric current flowing through a specific unit or device.

• It is typically measured in amperes (A) or milliamperes (mA).

• The current of a unit can vary depending on the specific device or circuit being discussed.

• For example, the current of a unit could refer to the current flowing through a resistor, a transistor, or a motor...read more
Answered by AI
Add your answer
Q4. Transformers rating in KVA
Ans. 
Transformers are rated in KVA (kilovolt-amperes) to indicate their power capacity.
• KVA stands for kilovolt-amperes, which is a unit of apparent power.

• The KVA rating of a transformer indicates the maximum amount of power it can handle.

• Transformers are available in various KVA ratings to suit different power requirements.

• Higher KVA ratings indicate higher power capacity.

• For example, a transformer with a 100 KVA rating can
Answered by AI
Add your answer
Q5. What is loop law?
Ans. 
Loop law, also known as Kirchhoff's voltage law, states that the sum of the voltages in any closed loop in a circuit is zero.
• Loop law is a fundamental principle in electrical engineering.

• It is also known as Kirchhoff's voltage law (KVL).

• According to loop law, the algebraic sum of the potential differences (voltages) around any closed loop in a circuit is always zero.

• It is based on the principle of conservation of energ...read more
Answered by AI
Add your answer

Q1. What is the Transformer
Ans. 
A transformer is a device that transfers electrical energy between two or more circuits through electromagnetic induction.
• Consists of two coils of wire, known as primary and secondary coils

• Primary coil receives electrical energy and creates a magnetic field

• Magnetic field induces a voltage in the secondary coil, transferring energy

• Used in power distribution, voltage regulation, and electrical isolation
Answered by AI
Add your answer
Q2. Electrical 8 equipment
Add your answer

Q1. Basic electrical engineering
Add your answer
Q2. Transmission line transformer electrical wiring etc
Add your answer

Q1. What is Transformer
Ans. 
A transformer is an electrical device that transfers electrical energy between two or more circuits through electromagnetic induction.
• Transformers are used to increase or decrease the voltage in an electrical circuit.

• They consist of two or more coils of wire, known as windings, that are wound around a core made of magnetic material.

• The primary winding receives electrical energy from a power source, while the secondary ...read more
Answered by AI
View 1 more answer
Q2. What is rectifier
Ans. 
A rectifier is an electrical device that converts alternating current (AC) to direct current (DC).
• Rectifiers are commonly used in power supplies to convert AC voltage to DC voltage.

• They are made up of diodes, which allow current to flow in only one direction.

• Rectifiers can be half-wave or full-wave, depending on the number of diodes used.

• Examples of rectifiers include bridge rectifiers, vacuum tube rectifiers, and soli
Answered by AI
View 1 more answer

Aptitiude, Reasoning , EEE basic Questions

Q1. Electrical Transformer
Add your answer
Q2. What is Transformer
Ans. 
A transformer is an electrical device that transfers electrical energy between two or more circuits through electromagnetic induction.
• Consists of two coils of wire, known as primary and secondary coils

• Primary coil receives electrical energy and creates a magnetic field

• Magnetic field induces a voltage in the secondary coil, transferring energy

• Used in power distribution, voltage regulation, and electrical isolation

• Exampl...read more
Answered by AI
Add your answer
Q3. What is mutual Induction
Ans. 
Mutual induction is the process where a changing current in one coil induces a voltage in another coil.
• Mutual induction occurs when two coils are placed close to each other and the magnetic field produced by one coil induces a voltage in the other coil.

• The induced voltage in the second coil is directly proportional to the rate of change of current in the first coil.

• This phenomenon is the basis for the operation of tran...read more
Answered by AI
Add your answer
Q4. What is flux, Current
Ans. 
Flux is the flow of electric or magnetic field lines through a surface, while current is the flow of electric charge.
• Flux is a measure of the flow of a physical property through a given area.

• In electromagnetism, flux refers to the flow of electric or magnetic field lines through a surface.

• Current is the flow of electric charge through a conductor.

• Flux and current are related through Faraday's law of electromagnetic ind
Answered by AI
Add your answer

Q1. Basic questions
Add your answer

Q1. Describe about the DTR. What are the material used in constrction of DTR Structure
Ans. 
DTR stands for Dead Time Recovery. It is a structure used in the oil and gas industry to separate gas and liquid phases.
• DTR is typically made of steel or other corrosion-resistant materials.

• The structure is designed to handle high pressure and temperature conditions.

• Common materials used in the construction of DTR include carbon steel, stainless steel, and duplex stainless steel.

• The choice of material depends on factor...read more
Answered by AI
Add your answer
Q2. Descibe about Bucoz relay & Its function.
Ans. 
A Bucoz relay is a type of protective relay used in power systems to detect faults and isolate them to prevent damage.
• Bucoz relay is a type of protective relay used in power systems.

• It functions by detecting faults in the system and isolating them to prevent damage.

• It helps in maintaining the stability and reliability of the power system.

• Bucoz relay operates based on the principle of electromagnetic induction.

• Examples ...read more
Answered by AI
Add your answer
Q3. Describe about Pipe earthing of DTR
Ans. 
Pipe earthing of DTR involves using a metal pipe buried in the ground to provide a low-resistance path for fault currents.
• Metal pipe is buried vertically in the ground near the DTR

• The pipe is filled with alternate layers of charcoal and salt to improve conductivity

• A copper wire is connected to the pipe and then to the DTR for grounding purposes
Answered by AI
Add your answer

Q1. What are your salary requirements.
Add your answer
Q2. Why you want join my organization
Add your answer