Satyam Venture Engineering Services Post Graduate Engineer Trainee [pget] Interview Questions and Answers

This round was conducted on online and it consists of Aptitude and core questions

Q1. 1.What is theories of failure?
Ans. 
Theories of failure are mathematical models used to predict the failure of materials under different loading conditions.
• Theories of failure help engineers design structures that can withstand different types of loads.

• Some common theories of failure include maximum shear stress theory, maximum normal stress theory, and maximum strain energy theory.

• These theories are based on different assumptions about the behavior of m...read more
Answered by AI
Add your answer
Q2. 2. What is the working principle of diesel cycle?
Ans. 
Diesel cycle is a thermodynamic cycle used in diesel engines to convert heat into work.
• Air is compressed in the cylinder, causing its temperature to rise.

• Fuel is injected into the cylinder, igniting due to the high temperature.

• The expanding gases push the piston, converting heat into mechanical energy.

• Exhaust gases are expelled from the cylinder.

• Diesel cycle is more efficient than Otto cycle used in gasoline engines.
Answered by AI
View 1 more answer

Q1. Self your introduction
Add your answer
Q2. Electrical vehicles, what is chassis
Add your answer
Q3. What is automobile, what is otto ,dual,diesels cycle difference
Ans. 
The question is about the basics of automobile engines and the differences between Otto, Dual, and Diesel cycles.
• Automobile is a vehicle powered by an engine that converts fuel into mechanical energy.

• Otto cycle is a four-stroke combustion cycle used in gasoline engines.

• Dual cycle is a modified version of the Otto cycle that includes a constant volume heat addition process.

• Diesel cycle is a four-stroke combustion cycle ...read more
Answered by AI
Add your answer
Q4. What is coefficient of performance input/output
Ans. 
Coefficient of performance (COP) is the ratio of output heat to input work or energy.
• COP is used to measure the efficiency of a heat pump or refrigeration system.

• It is calculated by dividing the output heat by the input work or energy.

• A higher COP indicates a more efficient system.

• For example, a heat pump with a COP of 3 can produce three units of heat for every unit of energy input.

• COP can also be expressed in terms o...read more
Answered by AI
Add your answer
Q5. How the otto cycle constants volume this process,
Ans. 
The Otto cycle is a constant volume process used in internal combustion engines.
• The Otto cycle consists of four processes: intake, compression, combustion, and exhaust.

• During the intake process, the fuel-air mixture is drawn into the cylinder.

• During the compression process, the mixture is compressed to a smaller volume, increasing its temperature and pressure.

• During the combustion process, the mixture is ignited, causi...read more
Answered by AI
Add your answer
Q6. What is the Duel cycle principles -both constant volume, and pressure
Ans. 
Dual cycle principles involve both constant volume and pressure processes in an engine cycle.
• Dual cycle is a combination of Otto and Diesel cycles.

• It involves two constant volume and one constant pressure processes.

• The first constant volume process is isentropic compression.

• The constant pressure process is combustion.

• The second constant volume process is isentropic expansion.

• It is used in gas turbine engines and some i
Answered by AI
Add your answer
Q7. Physical quantities length ,mass time
Add your answer
Q8. Efficiency of carnot T1/T2-T1
Ans. 
Efficiency of Carnot cycle is given by T1/T2-T1
• Efficiency of Carnot cycle is the maximum possible efficiency of a heat engine

• It depends only on the temperatures of the hot and cold reservoirs

• Efficiency = 1 - (T1/T2)

• T1 is the temperature of the cold reservoir and T2 is the temperature of the hot reservoir
Answered by AI
Add your answer

Basic questions related to mathematics and technical questions from engineering background.

Q1. Technical questions from mechanical engineering and subjects that we studied in engineering.
Add your answer
Q2. Material science questions
Add your answer
Q3. Question related to GD&T
Add your answer
Q4. Questions on lean manufacturing
Add your answer

Q1. Just basic introduction
Add your answer

Q1. A average of 30 min technical round questions related to the post you applied for.
Add your answer