Filter interviews by
Top trending discussions
I appeared for an interview in Aug 2019.
There are various types of structures, including buildings, bridges, dams, tunnels, and towers.
Structures can be classified based on their purpose, design, and materials used.
Buildings can be further classified into residential, commercial, and industrial structures.
Bridges can be classified into beam, arch, suspension, and cable-stayed bridges.
Dams can be classified into gravity, arch, buttress, and embankment dams.
Tu...
Density is the measure of mass per unit volume of a substance.
It is a physical property of matter.
It is calculated by dividing the mass of a substance by its volume.
Units of density include kg/m³, g/cm³, and lb/ft³.
Density can be used to identify substances and determine their purity.
For example, gold has a density of 19.3 g/cm³, while aluminum has a density of 2.7 g/cm³.
There are two types of density construction: compacted and loose.
Compacted density construction involves compressing the material to increase its density, such as in road construction.
Loose density construction involves leaving the material in its natural state, such as in landscaping.
The type of density construction used depends on the intended use of the material and the desired level of compaction.
Other factors that...
Tests for construction joints include visual inspection, water tightness test, and load transfer test.
Visual inspection to check for proper joint alignment and sealant application
Water tightness test to ensure no water leakage through the joint
Load transfer test to verify the joint can handle the intended load
Other tests may include pull-out test, shear test, and compression test
Testing frequency and methods may vary d...
posted on 23 Dec 2022
I applied via Walk-in and was interviewed in Aug 2022. There were 2 interview rounds.
posted on 13 Jul 2023
I applied via Walk-in and was interviewed before May 2021. There were 2 interview rounds.
CODAL provisions for concrete refer to the guidelines and regulations set by relevant authorities, while commands of software are the specific instructions or functions within a software program.
CODAL provisions for concrete include specifications for mix design, strength requirements, and durability standards.
Commands of software for site engineers may include functions for structural analysis, quantity takeoff, and p...
I applied via Naukri.com and was interviewed in Nov 2022. There were 2 interview rounds.
Safety measures at the site include wearing appropriate personal protective equipment, following safety protocols, conducting regular safety inspections, and providing safety training to all workers.
Wearing appropriate personal protective equipment such as helmets, gloves, and safety shoes
Following safety protocols and guidelines set by the company and regulatory bodies
Conducting regular safety inspections to identify ...
Yes, I am ready for remote locations as I am adaptable and have experience working in challenging environments.
I have previous experience working in remote locations.
I am adaptable and can easily adjust to new environments.
I am comfortable with limited resources and facilities.
I am prepared for potential challenges such as limited communication and transportation options.
Concrete mix design is the process of selecting suitable ingredients and determining their proportions to produce concrete with desired properties.
Concrete mix design involves selecting the right combination of cement, aggregates, water, and admixtures.
The proportions of each ingredient are determined based on the desired strength, workability, and durability of the concrete.
Factors such as the type of project, environ...
I applied via Campus Placement and was interviewed before May 2023. There was 1 interview round.
Design mix concrete is a mix of concrete prepared by a designer as per the required strength and durability, while nominal mix concrete is a mix of concrete prepared based on standard ratios without specific design requirements.
Design mix concrete is prepared by a designer based on specific requirements for strength and durability.
Nominal mix concrete is prepared based on standard ratios like 1:2:4 without specific des...
Knee bracing is a structural support used in construction to prevent lateral movement of beams or columns.
Knee bracing is a diagonal member used to connect a vertical member to a horizontal member in a structure.
It helps to resist lateral forces and prevent buckling or swaying of the structure.
Knee bracing is commonly used in steel frame construction to provide stability and support.
Examples include diagonal braces con
Different types of slabs include one-way slab, two-way slab, flat slab, ribbed slab, waffle slab, and hollow core slab.
One-way slab: supported on two opposite sides and bends in only one direction
Two-way slab: supported on all four sides and bends in two directions
Flat slab: without beams and supported directly on columns
Ribbed slab: with ribs on the underside for added strength and reduced weight
Waffle slab: with grid...
Different types of slabs foundation include raft, mat, flat plate, and waffle slab foundations.
Raft foundation: a solid reinforced concrete slab that covers the entire area under a building
Mat foundation: a thick concrete slab used to support heavy structures or buildings
Flat plate foundation: a simple and economical type of foundation with a uniform thickness
Waffle slab foundation: a type of foundation with grid-like
based on 1 review
Rating in categories
Senior Engineer
176
salaries
| ₹10.9 L/yr - ₹32 L/yr |
Process Engineer
50
salaries
| ₹6 L/yr - ₹12.6 L/yr |
Piping Designer
48
salaries
| ₹4.4 L/yr - ₹16 L/yr |
Piping Engineer
47
salaries
| ₹6 L/yr - ₹20 L/yr |
Instrument Engineer
38
salaries
| ₹6.8 L/yr - ₹26.8 L/yr |
L&T Construction
Saint-Gobain
AECOM
AtkinsRealis