Filter interviews by
Top trending discussions
posted on 18 Dec 2021
I appeared for an interview in Jun 2021.
The loads considered in telecom towers design include wind loads, dead loads, ice loads, and equipment loads.
Wind loads: Towers are designed to withstand the force of wind at different speeds and directions.
Dead loads: These include the weight of the tower structure itself and any permanent fixtures.
Ice loads: Towers in cold climates need to be designed to support the weight of ice accumulation.
Equipment loads: The wei...
Wind load calculation as per IS875 involves determining the wind pressure acting on the structure and calculating the resultant force.
Wind pressure is calculated based on the wind speed and the terrain category of the site
The pressure coefficients for different parts of the structure are determined based on the shape and orientation of the surface
The wind load acting on the structure is calculated by multiplying the pr...
I applied via Naukri.com and was interviewed in Jun 2022. There were 2 interview rounds.
To start OFC cable blowing, follow these steps
Ensure that the ducts are clean and free of any obstruction
Attach the cable blowing machine to the duct
Connect the cable to the machine and start the blowing process
Monitor the cable's progress and adjust the machine's speed as needed
Once the cable has been blown through the entire length of the duct, detach the machine and cable
posted on 14 Oct 2023
I applied via Walk-in and was interviewed in Sep 2023. There were 2 interview rounds.
The weight of green concrete varies depending on the mix design and components used.
The weight of green concrete typically ranges from 140 to 150 pounds per cubic foot.
Factors such as the type and amount of aggregates, cement, water, and admixtures used can affect the weight.
Lightweight concrete can have a lower weight, while high-density concrete can be heavier.
The weight of green concrete is important for structural
The formula for tensile strength of concrete is based on the cross-sectional area and maximum load applied.
Tensile Strength = Maximum Load / Cross-sectional Area
The units for tensile strength are typically in MPa (megapascals)
Tensile strength is an important property of concrete for determining its ability to resist tension forces
For example, if a concrete specimen with a cross-sectional area of 100 square millimeters ...
The water cement ratio of concrete refers to the ratio of the weight of water to the weight of cement used in a concrete mix.
The water cement ratio is a crucial factor in determining the strength and durability of concrete.
A lower water cement ratio results in stronger and more durable concrete.
The ideal water cement ratio varies depending on the type of concrete mix and its intended use.
For example, a typical water ce...
IS code of steel refers to the Indian Standard code for steel materials and products.
IS 2062:2011 - Steel for general structural purposes
IS 1786:2008 - High strength deformed steel bars and wires for concrete reinforcement
IS 8500:1991 - Structural steel - Microalloyed (medium and high strength qualities)
posted on 27 Jan 2024
I applied via Naukri.com and was interviewed in Apr 2024. There was 1 interview round.
I appeared for an interview before Mar 2024, where I was asked the following questions.
I have extensive experience in structural engineering, focusing on design, analysis, and project management across various sectors.
Worked on the design of a 20-story commercial building, ensuring compliance with local codes and safety standards.
Conducted structural analysis using software like SAP2000 and ETABS for various projects, improving efficiency by 30%.
Collaborated with architects and contractors to optimize de...
The density of cement is around 1440 kg/m³.
The density of cement varies depending on the type of cement.
The density of Portland cement is around 1440 kg/m³.
The density of lightweight cement is around 1000 kg/m³.
The density of high-density cement is around 3000 kg/m³.
Clear cover in column refers to the distance between the surface of the reinforcement and the outer surface of the concrete.
Clear cover is important to protect the reinforcement from corrosion and to ensure proper bonding between the reinforcement and concrete.
The required clear cover for columns depends on factors such as the type of structure, exposure conditions, and size of the reinforcement.
For example, in a coast...
Bending moment formula calculates the internal bending moment in a beam or structure.
Bending moment formula is M = F * d
M is the bending moment, F is the force applied, and d is the distance from the force to the point of interest
Bending moment can be positive or negative depending on the direction of the force and the orientation of the beam
Bending moment is an important factor in designing and analyzing structures
The thickness of compreg ply varies depending on its intended use and application. Its size can also vary depending on the manufacturer and customer requirements.
The thickness of compreg ply can range from 3mm to 25mm or more
The size of compreg ply can vary from 4ft x 8ft to 5ft x 10ft or more
The thickness and size of compreg ply can be customized based on the specific requirements of the project
Compreg ply is commonly...
The maximum repetition of ply shuttering depends on various factors such as quality of ply, weather conditions, and type of concrete.
The maximum repetition of ply shuttering can range from 5 to 20 times depending on the above factors.
If the quality of ply is good and weather conditions are favorable, the ply shuttering can be reused more number of times.
However, if the concrete mix is harsh or the weather conditions ar...
The consumption of shuttering oil per liter depends on the area covered.
The consumption of shuttering oil per liter can vary depending on factors such as the type of shuttering material, surface texture, and weather conditions.
On average, 1 liter of shuttering oil can cover approximately 10-15 square meters of surface area.
However, this can vary significantly based on the absorbency of the surface and the thickness of ...
The elongation % of fe550 steel varies depending on the specific grade and manufacturing process.
The elongation % of fe550 steel can range from 14% to 20%.
It is important to refer to the specifications provided by the manufacturer for accurate information.
The elongation % indicates the ability of the steel to deform before breaking under tension.
Fe550 steel is commonly used in construction and reinforcement application
Rolling margin of steel is the difference between the target thickness and the actual thickness after rolling.
Rolling margin is a measure of the accuracy of the rolling process.
It is calculated by subtracting the actual thickness of the steel after rolling from the target thickness.
A positive rolling margin means the steel is thicker than intended, while a negative rolling margin means it is thinner.
Rolling margin is i...
I applied via Walk-in and was interviewed in May 2022. There were 2 interview rounds.
Construction material and techniques
Construction labour management
Site work
Civil Site Engineer
9
salaries
| ₹2.4 L/yr - ₹5.6 L/yr |
Project Manager
7
salaries
| ₹7.2 L/yr - ₹24 L/yr |
Site Engineer
7
salaries
| ₹2 L/yr - ₹4.5 L/yr |
Assistant Manager
5
salaries
| ₹5 L/yr - ₹9 L/yr |
Senior Engineer
5
salaries
| ₹4.2 L/yr - ₹8.4 L/yr |
Lea Associates South Asia
McNally Bharat Engineering
R.V.R. PROJECTS
ABCI Infrastructures