Filter interviews by
I applied via India job and was interviewed in Jun 2024. There were 2 interview rounds.
I was interviewed before Feb 2024.
The seven quality control tools are essential for process improvement and problem-solving in engineering.
Check sheet: Used to collect and analyze data in a systematic way, such as tracking defects in a manufacturing process.
Pareto chart: Helps identify the most significant factors contributing to a problem by displaying them in descending order of frequency or impact.
Cause-and-effect diagram (Fishbone diagram): Visuali...
Autonomous maintenance is a key pillar of Total Productive Maintenance (TPM) and involves seven steps to empower operators to take care of their equipment.
Step 1: Initial Cleaning - Operators clean the equipment and surrounding area to identify abnormalities.
Step 2: Eliminate Sources of Contamination - Remove dirt, dust, and debris that can lead to breakdowns.
Step 3: General Inspection - Operators visually inspect the ...
OEE calculations involve Availability, Performance, and Quality factors to measure equipment efficiency.
Calculate Availability by dividing Operating Time by Planned Production Time.
Calculate Performance by dividing Actual Production by Maximum Possible Production.
Calculate Quality by dividing Good Units Produced by Total Units Started.
Implementing lean practices is mandatory for organizations to improve efficiency, reduce waste, and increase productivity.
Lean practices help organizations identify and eliminate waste in processes, leading to cost savings and improved efficiency.
By implementing lean practices, organizations can improve quality control and reduce defects in products or services.
Lean practices promote continuous improvement and empower ...
Downstream team members can be motivated through recognition, clear communication, opportunities for growth, and fostering a positive work environment.
Provide recognition for their hard work and achievements
Communicate clearly about goals, expectations, and feedback
Offer opportunities for growth and development, such as training or mentorship programs
Create a positive work environment through team-building activities a
Pareto analysis is a technique used to identify the most important factors contributing to a problem or situation.
Pareto analysis is based on the Pareto Principle, also known as the 80/20 rule, which states that roughly 80% of effects come from 20% of causes.
It involves identifying and prioritizing the factors that have the most significant impact on a particular outcome.
By focusing on addressing the most critical fact...
A Gemba walk is a Lean management technique where managers go to the actual workplace to observe operations and engage with employees.
Gemba walks involve observing processes, asking questions, and identifying opportunities for improvement.
Managers should focus on understanding the work being done and the challenges faced by employees.
Gemba walks help in building relationships with employees and fostering a culture of c...
Steps involved in performing safety risk assessments
Identify hazards and potential risks
Assess the likelihood and severity of each risk
Implement control measures to mitigate risks
Monitor and review the effectiveness of control measures
Document findings and recommendations
Communicate risks to relevant stakeholders
TPM stands for Total Productive Maintenance, a proactive approach to maintenance that aims to maximize equipment effectiveness.
TPM focuses on preventing equipment breakdowns through regular maintenance and employee involvement.
It involves autonomous maintenance, planned maintenance, and focused improvement activities.
TPM aims to improve overall equipment effectiveness (OEE) by reducing downtime, improving quality, and ...
Blaming staff without evidence is unprofessional and can damage morale and trust within the team.
Avoid jumping to conclusions without concrete evidence
Encourage open communication and transparency
Focus on problem-solving rather than assigning blame
Provide constructive feedback and support to help staff improve
Lead by example and take responsibility for mistakes
Directors may not always be aware of thefts due to lack of oversight, trust in employees, or focus on other priorities.
Directors may not be directly involved in day-to-day operations where thefts occur
There may be a lack of proper oversight or monitoring mechanisms in place
Directors may trust their employees and not suspect them of theft
Directors may be focused on other strategic priorities and not pay attention to pot
posted on 13 Aug 2024
3 rounds online, dsa, hr
posted on 22 Aug 2024
I applied via Campus Placement and was interviewed in Feb 2024. There were 3 interview rounds.
It was online coding test consist of 2 question
One from DP and other graph
One question of DP within in 45 min time constraints
Floor value of square root of a number is the largest integer less than or equal to the square root.
The floor value of square root of a number can be found using mathematical functions like floor() or integer division.
For example, the floor value of square root of 16 is 4, as sqrt(16) = 4.
For non-perfect square numbers, the floor value of square root can be calculated using approximation methods.
I applied via Walk-in and was interviewed before Oct 2022. There were 2 interview rounds.
PH is a measure of acidity or alkalinity of a solution. Normality and molarity are units of concentration in chemistry.
PH stands for potential of hydrogen and measures the acidity or alkalinity of a solution on a scale of 0 to 14.
Normality is a measure of concentration in chemistry, representing the number of equivalents of a substance per liter of solution.
Molarity is another measure of concentration, representing the...
posted on 6 Oct 2023
I applied via Campus Placement and was interviewed in Apr 2023. There were 3 interview rounds.
Level was medium to hard
To print a tree in anticlockwise direction, start from the bottom left and traverse each level from right to left.
Start from the bottom left of the tree
Traverse each level from right to left
Print the nodes as you traverse
Some old coding platform with limited testcases
posted on 20 Nov 2024
I applied via Naukri.com and was interviewed in May 2024. There were 2 interview rounds.
Coding round where they ask few coding questions
2 coding questions, aptitude and electronics
based on 1 interview
Interview experience
based on 1 review
Rating in categories
Electronics Engineer
4
salaries
| ₹0 L/yr - ₹0 L/yr |
Technician
3
salaries
| ₹0 L/yr - ₹0 L/yr |
Namaste India Foods
Bhagwati Products
Recipharm Pharmaservices
Patil Group