Filter interviews by
I appeared for an interview in Feb 2023.
FAR stands for Floor Area Ratio, which is the ratio of a building's total floor area to the size of the piece of land on which it is built. Floor area refers to the total area of a floor in a building, carpet area is the area within the walls, and built-up area includes carpet area plus the thickness of walls.
FAR (Floor Area Ratio) is the ratio of a building's total floor area to the size of the land it is built on.
Flo...
I applied via YouTube Naukariwala channel and was interviewed in Oct 2022. There were 4 interview rounds.
Top trending discussions
I appeared for an interview in Aug 2019.
There are various types of structures, including buildings, bridges, dams, tunnels, and towers.
Structures can be classified based on their purpose, design, and materials used.
Buildings can be further classified into residential, commercial, and industrial structures.
Bridges can be classified into beam, arch, suspension, and cable-stayed bridges.
Dams can be classified into gravity, arch, buttress, and embankment dams.
Tu...
Density is the measure of mass per unit volume of a substance.
It is a physical property of matter.
It is calculated by dividing the mass of a substance by its volume.
Units of density include kg/m³, g/cm³, and lb/ft³.
Density can be used to identify substances and determine their purity.
For example, gold has a density of 19.3 g/cm³, while aluminum has a density of 2.7 g/cm³.
There are two types of density construction: compacted and loose.
Compacted density construction involves compressing the material to increase its density, such as in road construction.
Loose density construction involves leaving the material in its natural state, such as in landscaping.
The type of density construction used depends on the intended use of the material and the desired level of compaction.
Other factors that...
Tests for construction joints include visual inspection, water tightness test, and load transfer test.
Visual inspection to check for proper joint alignment and sealant application
Water tightness test to ensure no water leakage through the joint
Load transfer test to verify the joint can handle the intended load
Other tests may include pull-out test, shear test, and compression test
Testing frequency and methods may vary d...
I applied via Walk-in and was interviewed before May 2021. There were 2 interview rounds.
CODAL provisions for concrete refer to the guidelines and regulations set by relevant authorities, while commands of software are the specific instructions or functions within a software program.
CODAL provisions for concrete include specifications for mix design, strength requirements, and durability standards.
Commands of software for site engineers may include functions for structural analysis, quantity takeoff, and p...
I appeared for an interview in Apr 2023.
Different types of slabs include one-way slab, two-way slab, flat slab, ribbed slab, waffle slab, and hollow core slab.
One-way slab: supported on two opposite sides and bends in only one direction
Two-way slab: supported on all four sides and bends in two directions
Flat slab: without beams and supported directly on columns
Ribbed slab: with ribs on the underside for added strength and reduced weight
Waffle slab: with grid...
Different types of slabs foundation include raft, mat, flat plate, and waffle slab foundations.
Raft foundation: a solid reinforced concrete slab that covers the entire area under a building
Mat foundation: a thick concrete slab used to support heavy structures or buildings
Flat plate foundation: a simple and economical type of foundation with a uniform thickness
Waffle slab foundation: a type of foundation with grid-like
I applied via Campus Placement and was interviewed in Oct 2024. There was 1 interview round.
A propped cantilever beam is a type of beam that is supported at one end and has a support (prop) at some point along its length.
Propped cantilever beams have a fixed support at one end and a prop at some point along the beam's length.
The prop helps to reduce the bending moment and deflection at the free end of the beam.
These beams are commonly used in construction to support overhanging structures or balconies.
Example...
The beam with the highest thickness will depend on the specific design and requirements of the structure.
The beam with the highest thickness will typically be a main load-bearing beam in the structure.
Factors such as the span of the beam, the load it needs to support, and the material used will determine the required thickness.
For example, a bridge beam supporting heavy traffic will likely have a higher thickness than
Hydro testing work involves testing pipelines, vessels, or other equipment using water or other liquids to ensure they can withstand pressure.
Hydro testing is a process used to check the integrity of pipelines, vessels, or other equipment by filling them with water or another liquid and pressurizing them to a specified level.
The test is conducted to ensure that the equipment can safely operate under normal operating co...
Managing a team involves effective communication, delegation, motivation, and conflict resolution.
Establish clear goals and expectations for the team
Communicate regularly and openly with team members
Delegate tasks based on team members' strengths and skills
Provide feedback and recognition for good work
Address conflicts and issues promptly and fairly
Lead by example and demonstrate a positive attitude
Encourage collaborat...
based on 2 interviews
Interview experience
based on 8 reviews
Rating in categories
Site Engineer
21
salaries
| ₹3.5 L/yr - ₹6 L/yr |
Civil Site Engineer
17
salaries
| ₹4 L/yr - ₹5.4 L/yr |
Senior Associate
12
salaries
| ₹4.2 L/yr - ₹5 L/yr |
Senior Engineer
6
salaries
| ₹4.5 L/yr - ₹9 L/yr |
Senior Manager
6
salaries
| ₹13.2 L/yr - ₹75 L/yr |
L&T Construction
AECOM
AtkinsRealis
Saipem