5 Motherson Automotive Technologies and Engineering Machine Maintenance Technician Interview Questions & Answers | Complete Prep Guide 2025

Motherson Automotive Technologies and Engineering Machine Maintenance Technician Interview Experiences

1 interview found

Machine Maintenance Technician Interview Questions & Answers

Anonymous

posted on 8 Feb 2023

Interview experience

Good

Difficulty level

Moderate

Process Duration

2-4 weeks

Result

Selected

I applied via Company Website and was interviewed before Feb 2022. There was 1 interview round.

Round 1 - Technical

(5 Questions)

Q1. About injection molding machine

Ans.

An injection molding machine also known as a injection press,is a machine for manufacturing plastic products by injection molding process it's consist of two parts an injection unit and a clamping unit

Answered Anonymously

Add your answer

Q2. Technical problem

Ans.

All shift isse like temperature problem, machine problem

Answered Anonymously

Add your answer

Q3. MTC problems and hopper problem,hrtc problem

Ans.

All problem like MTC motor not runnig and hooper material not heating and hrtc not working properly

Answered Anonymously

Add your answer

Q4. Motor overload problem

Ans.

Motor overload problem can be caused by various factors such as high current draw, mechanical issues, or incorrect settings.

Check for high current draw which may indicate a problem with the motor or the load it is driving.
Inspect for mechanical issues such as bearing failure or misalignment that could lead to increased resistance and overload.
Verify that the motor settings, such as voltage and current limits, are corre...

Answered by AI

Add your answer

Q5. Heater contactor problem

Ans.

The heater contactor problem may be caused by issues with the electrical connections, the contactor itself, or the control system.

Check the electrical connections for loose or damaged wires
Inspect the contactor for signs of wear or damage
Test the control system to ensure it is functioning properly
Consider environmental factors that may be affecting the contactor, such as temperature or moisture

Answered by AI

Add your answer

Top trending discussions

View All

Interview Tips & Stories

1d (edited)

timepasstiwari

A Digital Markter

Got Rejected In an Interview, Just Because I Didn’t Answer a Personal Question

So, I got invited for this interview, and they told me to be there at 9 AM. Of course, I get there early, like 8:30, because I don't want to be late. But then I end up waiting for 1.5 hours... read more

Got a question about Motherson Automotive Technologies and Engineering?

Ask anonymously on communities.

Interview questions from similar companies

ITI Electrician Interview Questions & Answers

UNO Minda

Anonymous

posted on 18 Feb 2022

I applied via Approached by Company and was interviewed before Feb 2021. There were 2 interview rounds.

Round 1 - One-on-one

(1 Question)

Q1. Machine operator

Add your answer

Round 2 - One-on-one

Interview Preparation Tips

Interview preparation tips for other job seekers - Machine operator
ATL,TL,5S, Kaizeen

Assistant Manager Interview Questions & Answers

UNO Minda

Anonymous

posted on 30 Dec 2021

I applied via Recruitment Consultant and was interviewed before Dec 2020. There was 1 interview round.

Interview Questionnaire

2 Questions

Q1. What was the defect u faced in plastic commodity

Ans.

I faced a defect in plastic commodity related to poor quality control during the manufacturing process.

The defect was in the form of cracks and breakages in the plastic products.
It was caused by inadequate monitoring and supervision during the molding and cooling stages.
The defect resulted in a high number of rejected products and customer complaints.
To address the issue, we implemented stricter quality control measure...

Answered by AI

View 2 more answers

Q2. Silver mark

Add your answer

Interview Preparation Tips

Interview preparation tips for other job seekers - Be confident .if anywhere u stuck u should accept and move to next one.

Senior Engineer Interview Questions & Answers

Ramkrishna Forgings

Anonymous

posted on 29 Apr 2021

I applied via Naukri.com and was interviewed in Oct 2020. There were 3 interview rounds.

Interview Questionnaire

3 Questions

Q1. Previous company job profile.

Add your answer

Q2. Plc related questions

Add your answer

Q3. Family background

Add your answer

Assistant Manager Interview Questions & Answers

Krishna Maruti

Anonymous

posted on 2 May 2019

I applied via Referral and was interviewed in Aug 2018. There were 2 interview rounds.

Interview Preparation Tips

Round: Resume Shortlist
Experience: By skill specialist & interview call;regarding knowledge of domain.

General Tips: Krishna maruti group is very excellent place of working.big group..many plants..zero tension of job security..means a viable place to do long service.no late sitting..
Culture is greater govt.than central govt offices.
Negative is higher mismatch between ctc & in hand.
10% of basic they deduct for superannuation fund from AM level..which is unaccountable.
Avg..1000rs deduction for lunch mandatory for bad canteen good & uniform deduction.
I means to say ,anybody should discuss only in hand salary during interview.means a monthly ctc of 60k became 45k & avg 4.5k will never receive(lunch/uniform/s.a.)
Duration: <1 week

Senior Engineer Interview Questions & Answers

Endurance Technologies

Anonymous

posted on 23 Oct 2021

I applied via Recruitment Consultant and was interviewed before Oct 2020. There were 3 interview rounds.

Interview Questionnaire

5 Questions

Q1. Which vehicle license you have?

Ans.

I have a valid driver's license for both cars and motorcycles.

I have a Class C license for cars
I also have a Class M license for motorcycles
I have a clean driving record with no accidents or violations

Answered by AI

View 1 more answer

Q2. What is CBS & ABS

Add your answer

Q3. Which segment of bike you ride

Ans.

I ride a road bike for commuting and a mountain bike for leisure.

I prefer road bikes for their speed and efficiency on paved roads.
I enjoy mountain biking for the challenge and adventure of off-road trails.
I also have experience with hybrid bikes for their versatility.
I prioritize safety and always wear a helmet and follow traffic laws.
I have participated in charity rides and group rides for fun and community.

Answered by AI

Add your answer

Q4. How you do the vehicle testing

Ans.

Vehicle testing involves various methods to ensure safety, performance, and compliance with regulations.

Testing can include physical tests such as crash tests, durability tests, and performance tests.
Simulation and modeling can also be used to test vehicle components and systems.
Testing must comply with regulations set by organizations such as the National Highway Traffic Safety Administration (NHTSA) and the European

Answered by AI

View 1 more answer

Q5. Which type of Homologation testing you do?

Ans.

We conduct various types of homologation testing depending on the product and its intended market.

We conduct safety testing to ensure compliance with local regulations.
We perform emissions testing to ensure compliance with environmental regulations.
We conduct performance testing to ensure the product meets the required standards.
We also conduct durability testing to ensure the product can withstand the expected wear an...

Answered by AI

View 3 more answers

Interview Preparation Tips

Interview preparation tips for other job seekers - That question were ask me for vehicle testing engineer & for test rider position

Senior Engineer Interview Questions & Answers

Suprajit Engineering

Anonymous

posted on 11 Jun 2022

I applied via Walk-in and was interviewed in May 2022. There were 4 interview rounds.

Round 1 - Resume Shortlist

Pro Tip by AmbitionBox:

Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.

View all Resume tips

Round 2 - Technical

(3 Questions)

Q1. Production related questions

Add your answer

Q2. Working flow rated questions

Add your answer

Q3. Any other factory related

Add your answer

Round 3 - HR

(1 Question)

Q1. Salary related questions

Add your answer

Round 4 - Group Discussion

Pro Tip by AmbitionBox:

Don’t treat group discussions as an argument. Group discussion is about reaching a meaningful conclusion.

View all GD tips

Interview Preparation Tips

Interview preparation tips for other job seekers - Need good job for my skills and production related.

Senior Engineer Interview Questions & Answers

Sundaram Clayton

Anonymous

posted on 6 Nov 2021

I applied via Naukri.com and was interviewed in May 2021. There were 3 interview rounds.

Interview Questionnaire

2 Questions

Q1. Technical questions regarding GDC process, rejection control and analysis..

Add your answer

Q2. Hypothetical questions, besed on situation handling, manpower handling and decision making

Add your answer

Interview Preparation Tips

Interview preparation tips for other job seekers - Be specific and speak confident

ITI Electrician Interview Questions & Answers

Suprajit Engineering

Anonymous

posted on 10 Jan 2024

Interview experience

Good

Difficulty level

Easy

Process Duration

Less than 2 weeks

Result

Selected

I applied via Internshala and was interviewed in Dec 2023. There was 1 interview round.

Round 1 - Technical

(2 Questions)

Q1. Comprssor & Dg Electrical

Add your answer

Q2. Air Comprssor working

Add your answer

Interview Preparation Tips

Interview preparation tips for other job seekers - Yes

Senior Engineer Interview Questions & Answers

Sundaram Clayton

Anonymous

posted on 19 Dec 2022

I applied via Walk-in and was interviewed before Dec 2021. There were 3 interview rounds.

Round 1 - Resume Shortlist

Pro Tip by AmbitionBox:

Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.

View all Resume tips

Round 2 - Technical

(2 Questions)

Q1. Write and explain GD&T symbols?

Ans.

GD&T symbols are used to specify the geometric requirements of a part or assembly.

GD&T stands for Geometric Dimensioning and Tolerancing
Symbols include: flatness, circularity, perpendicularity, concentricity, position, and more
Each symbol has a specific meaning and is used to communicate precise engineering requirements
GD&T is used in industries such as aerospace, automotive, and manufacturing
Example: A position symbol...

Answered by AI

Add your answer

Q2. Explain Cp, Cpk & Pp, Ppk?

Ans.

Cp, Cpk, Pp, and Ppk are statistical process control indices used to measure process capability and performance.

Cp and Cpk measure how well a process meets its specifications, with Cpk being more accurate for non-centered processes.
Pp and Ppk measure how well a process performs relative to its natural variation, with Ppk being more accurate for non-centered processes.
All four indices are calculated using the process me...

Answered by AI

Add your answer

Round 3 - Technical

(1 Question)

Q1. Related to GD&T, CNC programming knowledge, SPC, Fixture design and development, Tool design and development.

Add your answer

Interview Preparation Tips

Interview preparation tips for other job seekers - Willing to work extra hours and ready to compromise family members.

Motherson Automotive Technologies and Engineering Interview FAQs

How many rounds are there in Motherson Automotive Technologies and Engineering Machine Maintenance Technician interview?

Motherson Automotive Technologies and Engineering interview process usually has 1 rounds. The most common rounds in the Motherson Automotive Technologies and Engineering interview process are Technical.

What are the top questions asked in Motherson Automotive Technologies and Engineering Machine Maintenance Technician interview?

Some of the top questions asked at the Motherson Automotive Technologies and Engineering Machine Maintenance Technician interview -

Motor overload prob...read more
Heater contactor prob...read more
MTC problems and hopper problem,hrtc prob...read more

Tell us how to improve this page.

Motherson Automotive Technologies and Engineering Interviews By Designations

Interview Questions for Popular Designations

Motherson Automotive Technologies and Engineering Machine Maintenance Technician Interview Process

based on 1 interview

Interview experience

Good

Varroc Group Interview Questions

3.6

• 176 Interviews

UNO Minda Interview Questions

4.0

• 169 Interviews

Endurance Technologies Interview Questions

3.9

• 102 Interviews

Krishna Maruti Interview Questions

4.0

• 93 Interviews

Belrise Industries Interview Questions

3.8

• 84 Interviews

Delphi TVS Interview Questions

3.9

• 83 Interviews

Hyundai Mobis Interview Questions

3.8

• 63 Interviews

Faurecia Interview Questions

3.9

• 59 Interviews

ZF Commercial Vehicle Control Systems Interview Questions

3.9

• 57 Interviews

Tata Cummins Interview Questions

4.3

• 56 Interviews

View all

North Calcutta Polytechnic, Kolkata Placement Questions

1 Interview

P.S.N.A College of Engineering and Technology, Dindigul Placement Questions

1 Interview

College of Engineering, Anna University, Guindy Placement Questions

1 Interview

Kongu Engineering College, Erode Placement Questions

1 Interview

Naraina Vidya Peeth Engineering and Management Institute Placement Questions

1 Interview

View all

Motherson Automotive Technologies and Engineering Salaries in India

Engineer 305 salaries	₹0 L/yr - ₹0 L/yr
Assistant Engineer 279 salaries	₹0 L/yr - ₹0 L/yr
Senior Engineer 262 salaries	₹0 L/yr - ₹0 L/yr
Assistant Manager 240 salaries	₹0 L/yr - ₹0 L/yr
Trainee Technician 238 salaries	₹0 L/yr - ₹0 L/yr