Filter interviews by
I was interviewed in Sep 2022.
Top trending discussions
I was interviewed in Feb 2025.
posted on 19 Dec 2024
I applied via Approached by Company and was interviewed in Nov 2024. There was 1 interview round.
Power transformer installation involves several steps to ensure proper functioning and safety.
Selecting a suitable location for the transformer based on factors like accessibility, ventilation, and safety regulations
Preparing the foundation for the transformer to ensure stability and proper weight distribution
Transporting the transformer to the installation site using appropriate equipment and following safety protocol...
Various tests are performed on transformers to ensure their proper functioning and safety.
Insulation resistance test to check for any insulation breakdown
Turns ratio test to verify the turns ratio of primary and secondary windings
Polarity test to ensure correct polarity of windings
Winding resistance test to measure the resistance of windings
Dielectric strength test to check the insulation strength under high voltage
Sho...
posted on 9 Oct 2024
I applied via Referral and was interviewed in Sep 2024. There was 1 interview round.
The main reason for belt joint failure is usually due to improper installation or maintenance.
Improper installation of the belt joint, such as incorrect alignment or tensioning
Lack of proper maintenance, leading to wear and tear of the joint
Use of low-quality materials for the joint
Excessive load or stress on the belt joint
Environmental factors like temperature or humidity affecting the joint
The alignment maximum tolerance refers to the maximum allowable deviation from the specified alignment.
Alignment maximum tolerance is the maximum allowable deviation from the specified alignment.
It is typically expressed in terms of a percentage or a specific measurement unit.
For example, a machine part may have an alignment maximum tolerance of +/- 0.005 inches.
Exceeding the alignment maximum tolerance can lead to per
To replace the bucket wheel reclaimer luffing cylinder, follow these steps.
1. Shut down the machine and ensure all power sources are disconnected.
2. Remove any surrounding components that may obstruct access to the luffing cylinder.
3. Use appropriate tools to disconnect the hydraulic hoses and fittings from the cylinder.
4. Support the weight of the cylinder as it is removed to prevent damage to surrounding components.
5...
JSA stands for Job Safety Analysis, focusing on specific job tasks, while HIRA stands for Hazard Identification and Risk Assessment, focusing on overall workplace hazards.
JSA is task-specific, focusing on individual job tasks and potential hazards
HIRA is broader, looking at overall workplace hazards and assessing risks
JSA involves breaking down a job into steps and identifying potential hazards for each step
HIRA involv...
To create a PR in SAP, you can use transaction code ME51N or ME21N.
Use transaction code ME51N to create a purchase requisition in SAP.
Enter the necessary details such as material, quantity, delivery date, etc.
Save the purchase requisition and it will be created in the system.
Alternatively, you can also use transaction code ME21N to create a purchase order directly.
The procedure of pulley replacement involves identifying the faulty pulley, removing the old pulley, installing the new pulley, and testing the system.
Identify the faulty pulley by checking for any signs of wear or damage.
Use appropriate tools to remove the old pulley, such as a pulley puller or wrench.
Install the new pulley by aligning it properly and securing it in place.
Test the system to ensure the new pulley is fu...
PTW stands for Permit to Work, a procedure used to ensure that work is carried out safely in potentially hazardous environments.
PTW is a formal written system used to control certain types of work that are identified as potentially hazardous.
Before starting work, a permit must be obtained from a designated authority.
The permit outlines the work to be done, the hazards involved, and the necessary precautions to be taken...
I was interviewed in Nov 2024.
Electrical drives, substation, transformer etc
I applied via Job Portal
Modelling water supply
I was interviewed before Feb 2024.
posted on 21 Aug 2023
I applied via Recruitment Consulltant and was interviewed in Feb 2023. There were 4 interview rounds.
posted on 5 Oct 2023
I applied via Referral and was interviewed before Oct 2022. There were 2 interview rounds.
based on 3 interviews
Interview experience
based on 68 reviews
Rating in categories
Engineer
425
salaries
| ₹2.6 L/yr - ₹7.5 L/yr |
Senior Engineer
396
salaries
| ₹3 L/yr - ₹9.5 L/yr |
Assistant Manager
303
salaries
| ₹4.4 L/yr - ₹12 L/yr |
Assistant Engineer
288
salaries
| ₹2.2 L/yr - ₹7 L/yr |
Mechanical Engineer
129
salaries
| ₹2.5 L/yr - ₹7.6 L/yr |
Tata Steel
Steel Authority Of India
ArcelorMittal Nippon Steel
Jindal Steel and Power