Add office photos
Filter interviews by
Forza Medi Quality Engineer Interview Questions, Process, and Tips
Forza Medi Quality Engineer Interview Experiences
1 interview found
Selected
I applied via Naukri.com and was interviewed before Apr 2022. There were 2 interview rounds.
(7 Questions)
- Q1. What are the 7QCtools
- Ans.
The 7QC tools are a set of techniques used for quality control and improvement.
Check sheets: Used to collect and analyze data
Pareto charts: Used to identify the most frequent problems
Cause-and-effect diagrams: Used to identify the root cause of a problem
Histograms: Used to analyze data distribution
Scatter diagrams: Used to identify the relationship between two variables
Control charts: Used to monitor and control a proc
- Q2. What are the 5core tools
- Ans.
The 5 core tools are used in quality engineering to analyze and improve processes.
The 5 core tools are: Flowcharting, Check Sheets, Histograms, Pareto Charts, and Cause-and-Effect Diagrams.
Flowcharting is used to map out a process and identify areas for improvement.
Check Sheets are used to collect data and identify patterns.
Histograms are used to display data in a graphical format.
Pareto Charts are used to identify the...
- Q3. What are the levels of PPAP
- Ans.
PPAP has 5 levels, each with increasing requirements for documentation and testing.
Level 1: Part Submission Warrant (PSW)
Level 2: PSW with product samples and limited supporting data
Level 3: PSW with complete supporting data and test results
Level 4: PSW with statistical studies and capability analysis
Level 5: PSW with customer approval of all documentation and testing
- Q4. Tell me about the instrument which your are using on shop floor
- Ans.
We use a digital caliper on the shop floor to measure dimensions of parts.
The digital caliper has a range of up to 6 inches and can measure in both inches and millimeters.
It has a large LCD display for easy reading of measurements.
The caliper has a locking screw to hold the measurement in place.
We use it to measure the length, width, and thickness of parts to ensure they meet specifications.
It is also used to check the
- Q5. What is the difference between calibration and validation
- Ans.
Calibration ensures accuracy of measurement devices, while validation ensures that a process or system meets requirements.
Calibration involves adjusting a device to ensure it provides accurate measurements.
Validation involves testing a process or system to ensure it meets predetermined requirements or specifications.
Calibration is typically done on measurement devices such as thermometers, scales, and gauges.
Validation...
- Q6. What is NC how will you handle it
- Ans.
NC stands for Non-Conformance. As a Quality Engineer, I would handle NC by following a systematic approach to identify the root cause, implement corrective actions, and prevent recurrence.
Identify the non-conformance and document it
Investigate the root cause of the non-conformance
Implement corrective actions to address the root cause
Monitor the effectiveness of the corrective actions
Prevent recurrence by updating proce...
- Q7. Do you have ERP, computer knowledge
- Ans.
Yes, I have experience working with ERP systems and am proficient in computer skills.
I have worked with SAP and Oracle ERP systems in my previous roles
I am proficient in Microsoft Office Suite and have experience with data analysis tools like Tableau
I am comfortable working with both Windows and Mac operating systems
Interview Preparation Tips
Skills evaluated in this interview
Interview questions from similar companies
Selected
I applied via Walk-in and was interviewed in Jan 2023. There were 2 interview rounds.
(2 Questions)
- Q1. Any questions technical
- Q2. Any questions technical product
Interview Preparation Tips
Selected
I applied via Referral and was interviewed before May 2023. There was 1 interview round.
(5 Questions)
- Q1. 1) what is six sigma 2) what is iso 3) least count of vernier caliper 4) different types of measuring instruments 5) types of tolerances 6) types of fits 7) iso 13485 8) first angle and third angle metho...
- Ans.
Answers to various technical questions related to quality engineering.
Six Sigma is a set of techniques and tools for process improvement.
ISO is an international organization for standardization.
Least count of vernier caliper is the smallest measurement that can be read.
Types of measuring instruments include micrometers, calipers, rulers, etc.
Tolerances can be bilateral or unilateral.
Fits include clearance fit, interfer...
- Q2. What is iso-13485
- Q3. What is quality tools
- Ans.
Quality tools are techniques and methodologies used to ensure products or services meet customer requirements and standards.
Quality tools help identify and solve quality-related issues in a systematic way
Examples of quality tools include Pareto charts, fishbone diagrams, control charts, and statistical process control
These tools help in data analysis, problem-solving, decision-making, and continuous improvement
- Q4. What are the types of medical devices
- Q5. Grades of medical devices
Interview Preparation Tips
Skills evaluated in this interview
Quality Engineer Interview Questions & Answers
Degania Medical Devices
Anonymous
posted on 27 Aug 2021
Interview Questionnaire
2 Questions
Can you work in under pressure
- Q1. What is process control What work of plc and scada
- Ans.
Process control is the use of techniques and technologies to control and monitor a production process.
Process control involves monitoring and adjusting variables in a production process to ensure quality and efficiency.
PLC (Programmable Logic Controller) is a type of industrial control system that uses logic-based programming to automate processes.
SCADA (Supervisory Control and Data Acquisition) is a system that collec...
- Q2. Why Are you interested in this job
Interview Preparation Tips
U should save and clean your face
Skills evaluated in this interview
Quality Assurance Officer Interview Questions & Answers
Hindustan Syringes & Medical Devices
Anonymous
posted on 23 Apr 2023
Selected
I applied via Walk-in and was interviewed in Mar 2023. There were 4 interview rounds.
(2 Questions)
- Q1. First of all your all documents are absolutely varied then Tell them About yourself.
- Q2. Simple math formulas from algebra and trigonometry
Your past job designation and salary
(1 Question)
- Q1. Your eyes sight , handicap from leg or hand etc.
- Ans.
I do not have any visual or physical impairments.
I have no issues with my eyesight and do not require any corrective lenses.
I do not have any physical handicaps affecting my legs or hands.
I am fully capable of performing all duties required for the Quality Assurance Officer position.
Interview Preparation Tips
- Mathematics
- Chemistry
I applied via campus placement at Uttar Pradesh Technical University, Lucknow and was interviewed in Jun 2019. There were 4 interview rounds.
Interview Questionnaire
3 Questions
- Q1. How you can control the speed by pressure?
- Ans.
Speed can be controlled by adjusting the pressure of the fluid or gas that powers the system.
Pressure can be increased or decreased to control the speed of a system.
This is commonly used in hydraulic and pneumatic systems.
For example, in a hydraulic system, increasing the pressure of the fluid can increase the speed of a cylinder.
Similarly, in a pneumatic system, increasing the pressure of the gas can increase the spee...
- Q2. What is hydraulic? explain the example and what is the reason of its failure?
- Ans.
Hydraulic refers to the use of fluids to transmit power or energy.
Hydraulic systems use liquids such as oil or water to transmit power.
Examples include hydraulic brakes in cars and hydraulic lifts in buildings.
Failure can occur due to leaks, blockages, or mechanical issues.
Regular maintenance and inspection can prevent failure and ensure proper functioning.
- Q3. What is the plc and its role in automation?
- Ans.
PLC stands for Programmable Logic Controller. It is a digital computer used for automation of electromechanical processes.
PLC is used to control and monitor industrial processes.
It is programmed using ladder logic or other programming languages.
PLC can be used for various applications such as controlling traffic lights, assembly lines, and HVAC systems.
It can communicate with other devices and systems through various c...
Interview Preparation Tips
be confident.. 😀
Skills evaluated in this interview
Selected
I applied via Referral and was interviewed before May 2023. There was 1 interview round.
(5 Questions)
- Q1. 1) what is six sigma 2) what is iso 3) least count of vernier caliper 4) different types of measuring instruments 5) types of tolerances 6) types of fits 7) iso 13485 8) first angle and third angle metho...
- Ans.
Answers to various technical questions related to quality engineering.
Six Sigma is a set of techniques and tools for process improvement.
ISO is an international organization for standardization.
Least count of vernier caliper is the smallest measurement that can be read.
Types of measuring instruments include micrometers, calipers, rulers, etc.
Tolerances can be bilateral or unilateral.
Fits include clearance fit, interfer...
- Q2. What is iso-13485
- Q3. What is quality tools
- Ans.
Quality tools are techniques and methodologies used to ensure products or services meet customer requirements and standards.
Quality tools help identify and solve quality-related issues in a systematic way
Examples of quality tools include Pareto charts, fishbone diagrams, control charts, and statistical process control
These tools help in data analysis, problem-solving, decision-making, and continuous improvement
- Q4. What are the types of medical devices
- Q5. Grades of medical devices
Interview Preparation Tips
Skills evaluated in this interview
Quality Engineer Interview Questions & Answers
Degania Medical Devices
Anonymous
posted on 27 Aug 2021
Interview Questionnaire
2 Questions
Can you work in under pressure
- Q1. What is process control What work of plc and scada
- Ans.
Process control is the use of techniques and technologies to control and monitor a production process.
Process control involves monitoring and adjusting variables in a production process to ensure quality and efficiency.
PLC (Programmable Logic Controller) is a type of industrial control system that uses logic-based programming to automate processes.
SCADA (Supervisory Control and Data Acquisition) is a system that collec...
- Q2. Why Are you interested in this job
Interview Preparation Tips
U should save and clean your face
Skills evaluated in this interview
Quality Supervisor Interview Questions & Answers
Vitromed Healthcare
Anonymous
posted on 20 Mar 2024
Selected
I applied via Company Website and was interviewed in Sep 2023. There was 1 interview round.
(1 Question)
- Q1. Inspection on medical components
Selected
I applied via Walk-in and was interviewed in Jan 2023. There were 2 interview rounds.
(2 Questions)
- Q1. Any questions technical
- Q2. Any questions technical product
Interview Preparation Tips
Forza Medi Interview FAQs
Tell us how to improve this page.
Interview Questions for Popular Designations
- Quality Inspector Interview Questions
- Senior Quality Engineer Interview Questions
- Quality Controller Interview Questions
- Quality Assurance Interview Questions
- Quality Manager Interview Questions
- Quality Executive Interview Questions
- Quality Assurance Officer Interview Questions
- Executive Quality Assurance Interview Questions
- Show more
People are getting interviews through
Interview Questions from Similar Companies
Forza Medi Quality Engineer Reviews and Ratings
based on 2 reviews
Rating in categories
|
Assistant Manager
18
salaries
|  ₹5.1 L/yr - ₹9.9 L/yr |
|
Deputy Manager
15
salaries
| ₹8.1 L/yr - ₹11.1 L/yr |
|
Production Engineer
9
salaries
| ₹2.2 L/yr - ₹3.4 L/yr |
|
Senior Engineer
8
salaries
| ₹4.5 L/yr - ₹7.5 L/yr |
|
Quality Engineer
8
salaries
| ₹2.2 L/yr - ₹3.2 L/yr |
Apollo Hospitals
Fortis Healthcare
Manipal Hospitals
Columbia Asia
Calculate your in-hand salary
- Home >
- Interviews >
- Forza Medi Interview Questions >
- Forza Medi Quality Engineer Interview Questions
