Upload Button Icon Add office photos

Burns & McDonnell

Compare button icon Compare button icon Compare

Filter interviews by

Burns & McDonnell Civil Graduate Engineer Trainee Interview Questions, Process, and Tips

Updated 27 Jun 2024

Burns & McDonnell Civil Graduate Engineer Trainee Interview Experiences

1 interview found

Interview experience
5
Excellent
Difficulty level
Hard
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Campus Placement and was interviewed before Jun 2023. There were 2 interview rounds.

Round 1 - Technical 

(2 Questions)

  • Q1. Stress strain diagram of the beam
  • Ans. 

    Stress strain diagram shows the relationship between stress and strain in a material.

    • The stress strain diagram typically consists of a linear elastic region, a yield point, plastic deformation, and ultimate failure.

    • The slope of the linear elastic region represents the material's modulus of elasticity.

    • The yield point indicates the point at which the material begins to deform plastically.

    • The area under the stress strain ...

  • Answered by AI
  • Q2. Which is code iss used for rcc
  • Ans. 

    IS 456 is the code used for RCC (Reinforced Cement Concrete) in India.

    • IS 456 is the Indian Standard code for the design and construction of reinforced concrete structures.

    • It provides guidelines for the selection of materials, mix design, construction practices, and quality control.

    • For example, IS 456 specifies the minimum grade of concrete, minimum cover to reinforcement, and detailing requirements for RCC structures.

  • Answered by AI
Round 2 - Technical 

(2 Questions)

  • Q1. Design steps of foundation
  • Ans. 

    Design steps of foundation involve site investigation, soil testing, foundation type selection, structural design, and construction.

    • Site investigation to assess soil conditions and load-bearing capacity

    • Soil testing to determine soil properties and behavior under load

    • Selection of appropriate foundation type based on soil conditions and structural requirements (e.g. shallow foundation, deep foundation)

    • Structural design o...

  • Answered by AI
  • Q2. Design steps of the slab
  • Ans. 

    Design steps of the slab involve determining the type of slab, calculating loads, selecting materials, and detailing reinforcement.

    • Determine the type of slab based on the structural requirements and architectural design.

    • Calculate the loads that the slab will be subjected to, including dead loads, live loads, and other imposed loads.

    • Select appropriate materials for the slab, considering factors such as strength, durabil...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Prepared technical in deep

Interview questions from similar companies

I applied via Naukri.com and was interviewed before Nov 2019. There was 1 interview round.

Interview Questionnaire 

4 Questions

  • Q1. Basics related to piperack design
  • Q2. Design parameters for steel structure
  • Ans. 

    Design parameters for steel structure

    • Load capacity and distribution

    • Material strength and durability

    • Environmental factors such as wind and seismic activity

    • Connection details and joint design

    • Fire resistance and protection measures

  • Answered by AI
  • Q3. Number of years exposure to staad
  • Ans. 

    I have 5 years of exposure to STAAD software.

    • I have used STAAD for various structural analysis and design projects.

    • I am proficient in using STAAD for modeling, analysis, and design of steel and concrete structures.

    • I have experience in using STAAD for seismic analysis and design of structures.

    • I have also used STAAD for foundation design and analysis.

    • I keep myself updated with the latest versions and features of STAAD so

  • Answered by AI
  • Q4. Grating design and deflection limits

Interview Preparation Tips

Interview preparation tips for other job seekers - Be positive & confident

Interview Questionnaire 

1 Question

  • Q1. Hard core techanical

Interview Questionnaire 

5 Questions

  • Q1. Seismic design of building, criteria, type of checks in building with respect to seismic, analysis approach
  • Q2. Pile and foundation detail, structural system in building, shear wall, dual system implications
  • Q3. Steel structure- Class of section, connection detail, slender member design criteria
  • Q4. Building irregularities type
  • Q5. Nature of scope of work performed, understanding of coordination approach, software knowledge
Interview experience
3
Average
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
Selected Selected

I appeared for an interview before Apr 2024, where I was asked the following questions.

  • Q1. How do you handle conflict
  • Q2. How do you manage pressure
  • Ans. 

    I manage pressure by prioritizing tasks, maintaining clear communication, and practicing stress-relief techniques.

    • Prioritization: I use tools like the Eisenhower Matrix to identify urgent and important tasks, ensuring I focus on what truly matters.

    • Time Management: I break projects into smaller tasks with deadlines, which helps me avoid feeling overwhelmed.

    • Clear Communication: I keep stakeholders informed about progress...

  • Answered by AI
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
6-8 weeks
Result
Selected Selected

I applied via Company Website and was interviewed before Jan 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. About your self. About casting yard. About Methodology of casting of different structures. About site progress planning and time cycle of progress. This process is for 30-40 minutes.
Round 3 - HR 

(1 Question)

  • Q1. Details of my Education and experience. Salary negotiation and finalization of joining.

Interview Preparation Tips

Topics to prepare for AECOM Senior Engineer interview:
  • Civil Construction
  • IS Code
  • Your expertise area
Interview preparation tips for other job seekers - Prepare before going to attend an interview on all subject not only in your expertise area.
Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Whate are different bus bar schemes?
  • Ans. 

    Bus bar schemes are different ways of connecting bus bars in power systems.

    • Single bus bar scheme

    • Double bus bar scheme

    • Main and transfer bus bar scheme

    • Ring bus bar scheme

    • Breaker and a half scheme

    • Mesh bus bar scheme

  • Answered by AI
  • Q2. What are the equipment sequence for any line bay?
  • Ans. 

    The equipment sequence for any line bay starts with the circuit breaker and ends with the transformer.

    • The circuit breaker is the first equipment in the sequence.

    • Next comes the isolator switch.

    • After that, the earth switch is operated.

    • Then the line disconnector is opened.

    • Finally, the transformer is disconnected from the line.

    • The sequence is reversed when the line bay is put back into service.

  • Answered by AI
Round 3 - HR 

(2 Questions)

  • Q1. What you want to leave your current organization?
  • Q2. Are you comfortable to relocate to another city?

Interview Preparation Tips

Interview preparation tips for other job seekers - Always be prepare about possible questions and be confident while giving interview
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Naukri.com and was interviewed in Jul 2023. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Prepare basics properly before going for interview, they mostly ask less questions with more depth.
  • Q2. Draw BMD for sway frame.
  • Ans. 

    BMD for sway frame is a diagram showing the variation of bending moment along the length of the frame.

    • BMD for sway frame will have a shape similar to a zigzag pattern due to the presence of sway in the frame.

    • The bending moment will be maximum at the points where the frame experiences maximum sway.

    • The BMD can be drawn by analyzing the internal forces and moments acting on the frame.

  • Answered by AI
Round 3 - One-on-one 

(3 Questions)

  • Q1. Draw piperack elevations
  • Ans. 

    Drawing piperack elevations involves creating detailed drawings of the structure from different viewpoints.

    • Start by determining the dimensions and layout of the piperack

    • Use software like AutoCAD to create accurate and detailed drawings

    • Include all necessary details such as pipe sizes, supports, and connections

    • Label all components clearly for easy understanding

    • Review and revise the drawings as needed for accuracy

  • Answered by AI
  • Q2. Anchor bolt design
  • Q3. Base plate design
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
-

I applied via Campus Placement and was interviewed before Jul 2022. There were 4 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Resume Shortlist 

(2 Questions)

  • Q1. Basics of civil engineering with main focus on strength of materials, structural analysis and design
  • Q2. Bending moment diagrams
Round 3 - Technical 

(2 Questions)

  • Q1. Basics from every subject
  • Q2. Strength of materials andstructure analysis
  • Ans. 

    Strength of materials and structure analysis involves studying the behavior of materials under various loads and analyzing the stability and strength of structures.

    • Understanding material properties such as stress, strain, and elasticity is crucial in analyzing the strength of materials.

    • Structural analysis involves determining the internal forces and stresses in a structure to ensure it can support the applied loads.

    • Com...

  • Answered by AI
Round 4 - HR 

(1 Question)

  • Q1. General questions about acadamic and other

Interview Preparation Tips

Interview preparation tips for other job seekers - Be perfect with your basics
Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(4 Questions)

  • Q1. Descriptive type questions
  • Q2. Bending moment and shear force diagrams
  • Q3. Questions from strength of materials
  • Q4. Structural analysis
Round 2 - Group Discussion 

General topics will be asked

Round 3 - Interview 

(1 Question)

  • Q1. Technical questions

Burns & McDonnell Interview FAQs

How many rounds are there in Burns & McDonnell Civil Graduate Engineer Trainee interview?
Burns & McDonnell interview process usually has 2 rounds. The most common rounds in the Burns & McDonnell interview process are Technical.
What are the top questions asked in Burns & McDonnell Civil Graduate Engineer Trainee interview?

Some of the top questions asked at the Burns & McDonnell Civil Graduate Engineer Trainee interview -

  1. Which is code iss used for ...read more
  2. Stress strain diagram of the b...read more
  3. Design steps of foundat...read more

Tell us how to improve this page.

Burns & McDonnell Civil Graduate Engineer Trainee Interview Process

based on 1 interview

Interview experience

5
  
Excellent
View more

Interview Questions from Similar Companies

AECOM Interview Questions
4.2
 • 120 Interviews
AtkinsRealis Interview Questions
3.9
 • 89 Interviews
Bechtel Interview Questions
4.0
 • 68 Interviews
Samsung E&A Interview Questions
4.0
 • 61 Interviews
Saipem Interview Questions
4.1
 • 47 Interviews
Tractebel Interview Questions
4.1
 • 42 Interviews
Ramboll Interview Questions
4.1
 • 39 Interviews
Aker Solutions Interview Questions
4.0
 • 35 Interviews
View all
Electrical Engineer
92 salaries
unlock blur

₹4.8 L/yr - ₹10.1 L/yr

Electrical Designer
54 salaries
unlock blur

₹4 L/yr - ₹13.8 L/yr

Senior Associate Engineer
53 salaries
unlock blur

₹7.5 L/yr - ₹12 L/yr

Project Control Engineer
50 salaries
unlock blur

₹5.5 L/yr - ₹10 L/yr

Senior Electrical Engineer
36 salaries
unlock blur

₹8 L/yr - ₹20.1 L/yr

Explore more salaries
Compare Burns & McDonnell with

AECOM

4.2
Compare

AtkinsRealis

3.9
Compare

Saipem

4.1
Compare

Nasser S. Al Hajri Corporation

3.6
Compare
Did you find this page helpful?
Yes No
write
Share an Interview