Adani Power Junior Engineer Interview Questions and Answers for Experienced

Safety measures to be followed while working at heights

• Use of proper personal protective equipment (PPE) like harness, helmet, etc.

• Proper training and certification of workers

• Regular inspection and maintenance of equipment and tools

• Proper communication and coordination among workers

• Adherence to safety guidelines and regulations

• Proper risk assessment and hazard identification

• Use of guardrails, safety nets, and other fal...read more

Wind turbines convert wind energy into electrical energy.

• Wind turbines consist of blades, a rotor, a generator, and a tower.

• The blades capture the wind and turn the rotor.

• The rotor spins the generator, which produces electricity.

• The tower supports the turbine and raises it above the ground for better wind access.

• Wind turbines require consistent wind speeds of at least 6-9 mph to generate electricity.

• The electricity gen...read more

Salary for Junior Engineer varies based on experience and industry standards.

• Salary can range from $50,000 to $80,000 per year depending on location and company

• Experience and education level can also impact salary

• Research industry standards and negotiate salary during the hiring process

Synchronous motor runs at a constant speed while hysteresis motor has a rotor that follows the rotating magnetic field.

• Synchronous motor is used in applications where constant speed is required, such as in clocks and timers.

• Hysteresis motor is used in applications where precise control of speed is required, such as in record players and tape recorders.

• Synchronous motor has a stator and rotor that rotate at the same spe...read more

PLC is a hardware device that controls industrial processes, while SCADA is a software system that monitors and controls those processes.

• PLC is a programmable logic controller that controls the input/output of industrial processes.

• SCADA is a supervisory control and data acquisition system that collects and analyzes data from the industrial processes.

• PLC is a hardware device, while SCADA is a software system.

• PLC is used...read more

Relays are used for low power applications while contactors are used for high power applications.

• Relays are typically used in control circuits to switch low power loads such as lights and fans.

• Contactors are used to switch high power loads such as motors and compressors.

• Relays have a lower current rating than contactors.

• Contactors have larger contacts and can handle higher currents than relays.

• Relays are typically smal...read more

Switches are used to control the flow of current in a circuit, while relays are used to switch a circuit on or off.

• Switches are manually operated, while relays are electrically operated.

• Switches are used in low voltage applications, while relays are used in high voltage applications.

• Switches are simple in construction, while relays are more complex.

• Examples of switches include light switches and toggle switches, while ...read more

Switch is an electronic component used to connect or disconnect a circuit while a timer is a device used to measure time intervals.

• Switch is used to turn on/off a device while timer is used to control the duration of a device's operation.

• Switch is a binary device with two states (on/off) while timer can be analog or digital and can measure time in seconds, minutes, or hours.

• Examples of switches include light switches, ...read more

Daily breakdowns of wind turbine generators, troubleshooting methods, and how components work together.

• Daily breakdowns can include issues with gearbox, blades, or electrical systems.

• Troubleshooting involves identifying the root cause of the issue and fixing it efficiently.

• Components like the rotor, generator, and tower work together to convert wind energy into electricity.

There are various types of motors such as AC, DC, stepper, servo, etc. DOL starter is a type of starter used for induction motors.

• Types of motors include AC, DC, stepper, servo, etc.

• DOL starter stands for Direct-On-Line starter.

• It is used for induction motors.

• It provides full voltage to the motor at the start.

• It is the simplest and cheapest type of starter.

• Other types of starters include star-delta, soft starter, etc.

My demand is for a challenging and dynamic work environment where I can apply my engineering skills and learn new ones.

• I am looking for a company that values innovation and creativity

• I want to work with a team that is passionate about their work

• I am interested in opportunities for professional growth and development

• Examples of companies I admire include SpaceX, Tesla, and Google