Filter interviews by
I applied via Recruitment Consulltant and was interviewed in Sep 2023. There was 1 interview round.
The internal diameter of a bearing with the number 6205 is 25 mm.
The last two digits of the bearing number represent the bore diameter in millimeters
In this case, the '05' in 6205 indicates a bore diameter of 25 mm
Centrifugal pumps use rotational motion to create flow, while reciprocating pumps use back-and-forth motion.
Centrifugal pumps use a rotating impeller to create a centrifugal force that pushes the fluid through the pump.
Reciprocating pumps use a piston or diaphragm that moves back and forth to create pressure and move the fluid.
Centrifugal pumps are typically used for high flow rate, low pressure applications like water...
The number of welding rod used in MS welding process is typically 6013 or 7018.
Common welding rods used in MS welding are 6013 and 7018.
6013 welding rod is used for light to medium penetration on thin metals.
7018 welding rod is used for high penetration and strength on thicker metals.
Measure the dimensions of the shaft and housing to determine the size of the missing oil seal.
Measure the diameter of the shaft where the oil seal sits
Measure the diameter of the housing where the oil seal fits
Check the depth of the seal groove in the housing
Consult equipment manuals or manufacturers for standard sizes
Use a caliper or micrometer for accurate measurements
z, zz, rs, 2rs are suffixes used in bearing codes to indicate different types of seals or shields.
z: indicates a metal shield on one side of the bearing
zz: indicates metal shields on both sides of the bearing
rs: indicates a rubber seal on one side of the bearing
2rs: indicates rubber seals on both sides of the bearing
I applied via Walk-in and was interviewed in May 2022. There were 2 interview rounds.
Different methods of sterilization include heat, radiation, chemicals, and filtration.
Heat sterilization methods include autoclaving, dry heat, and flaming.
Radiation sterilization methods include gamma radiation and electron beam radiation.
Chemical sterilization methods include ethylene oxide gas and hydrogen peroxide vapor.
Filtration sterilization methods involve passing substances through filters with small pore size...
A Microbiology graduate with a Toxicology post-graduate degree can benefit the company by bringing a unique combination of skills and knowledge to the QA Analyst role.
The candidate can apply their understanding of microbiology to identify potential sources of contamination in the production process.
Their knowledge of toxicology can help in assessing the safety of products and identifying any potential risks or hazards.
...
QA stands for Quality Assurance. They are responsible for ensuring that the software meets the required quality standards.
Develop and execute test cases
Identify and report defects
Collaborate with developers to resolve issues
Ensure adherence to quality standards and processes
Provide feedback on usability and functionality
Conduct regression testing
Maintain test documentation
Different types of verification and their sequence.
Static Verification (Requirements, Design, Code)
Dynamic Verification (Unit Testing, Integration Testing, System Testing, Acceptance Testing)
Alpha Testing
Beta Testing
Regression Testing
To train other department personnel to operate a machine, I would follow a systematic approach.
Assess the trainees' existing knowledge and skills
Create a training plan with clear objectives and a structured curriculum
Provide hands-on training with the machine, explaining each step and demonstrating best practices
Offer opportunities for trainees to practice operating the machine under supervision
Conduct regular assessme...
URS stands for User Requirement Specification. It is a document that outlines the requirements of a software system from a user's perspective.
URS is a document that captures the user's requirements for a software system.
It outlines the functional and non-functional requirements of the system.
It is used as a basis for designing and developing the system.
URS is an important document in the software development life cycle...
Top trending discussions
posted on 10 Jul 2017
I was interviewed before Jul 2016.
I was interviewed in Sep 2016.
Pneumatic systems use compressed air to transmit power, while hydraulic systems use fluid to transmit power.
Pneumatic systems use air as the working fluid, while hydraulic systems use liquid.
Pneumatic systems are typically used for lighter loads and faster movements, while hydraulic systems are used for heavier loads and slower movements.
Pneumatic systems are generally less expensive and easier to maintain compared to ...
There are several types of welding techniques used in various industries.
Arc welding: Uses an electric arc to create heat and join metals.
MIG welding: Uses a consumable wire electrode and shielding gas to join metals.
TIG welding: Uses a non-consumable tungsten electrode and inert gas to join metals.
Spot welding: Joins metal sheets by applying pressure and heat at specific points.
Flux-cored arc welding: Similar to MIG w...
CNC and lathe machines are used for precision cutting and shaping of materials.
CNC machines use computer programming to control the cutting tools, allowing for highly precise and complex shapes to be created.
Lathe machines are used for turning and shaping cylindrical objects, such as metal rods or wooden dowels.
Both machines are commonly used in manufacturing and engineering industries.
Examples of products made using C...
UPLC stands for Ultra Performance Liquid Chromatography.
UPLC is a technique used in analytical chemistry to separate, identify, and quantify components in a mixture.
It is an advanced form of liquid chromatography that utilizes smaller particle sizes and higher pressures for faster and more efficient separations.
UPLC is commonly used in pharmaceutical, environmental, and food analysis.
It offers improved resolution, sens...
I applied via Referral and was interviewed in Nov 2021. There were 2 interview rounds.
HPLC INSTRUMENTATION
TOTOAL ANALYTICAL QUESTIONS
I applied via Referral and was interviewed before Apr 2020. There were 3 interview rounds.
I applied via Approached by Company and was interviewed before Jun 2021. There were 2 interview rounds.
based on 1 interview
Interview experience
based on 13 reviews
Rating in categories
ADL Officer
27
salaries
| ₹0 L/yr - ₹0 L/yr |
Formulation Scientist
6
salaries
| ₹0 L/yr - ₹0 L/yr |
Project Engineer
4
salaries
| ₹0 L/yr - ₹0 L/yr |
Executive Accountant
4
salaries
| ₹0 L/yr - ₹0 L/yr |
Executive Quality Assurance
4
salaries
| ₹0 L/yr - ₹0 L/yr |
Cipla
Sun Pharmaceutical Industries
DRJ & CO
Biocon Limited