i
Sony
Proud winner of ABECA 2024 - AmbitionBox Employee Choice Awards
Filter interviews by
Diagnosing circuit diagrams involves analyzing components, connections, and signals to identify issues or faults.
Identify all components in the circuit diagram
Check for proper connections between components
Analyze signal flow through the circuit
Look for any short circuits or open circuits
Use tools like multimeters for testing components
A power supply circuit diagram is a visual representation of the components and connections used to provide electrical power to a device.
Includes components such as transformers, rectifiers, capacitors, and voltage regulators
Shows the flow of electricity from the input source to the output load
May include symbols for AC and DC power sources, ground connections, and voltage levels
Common types include linear power suppli...
Top trending discussions
A wire harness is a collection of wires, cables, and connectors that transmit electrical signals and power between different components in a system.
Wire harnesses provide a neat and organized way to route and protect wires in a system.
They ensure proper connectivity and prevent wire damage or short circuits.
Wire harnesses simplify troubleshooting and maintenance by allowing easy identification and replacement of faulty...
Sputtering is a process used in manufacturing to deposit thin films of material onto a surface.
Sputtering is a physical vapor deposition technique.
It involves bombarding a target material with high-energy ions or atoms.
This bombardment dislodges atoms from the target material, which then deposit onto a substrate.
Sputtering is commonly used in the production of semiconductor devices, solar cells, and thin film coatings.
...
I applied via LinkedIn and was interviewed before Dec 2020. There were 3 interview rounds.
I applied via Naukri.com and was interviewed before Dec 2019. There were 5 interview rounds.
I applied via Walk-in and was interviewed before Dec 2019. There were 4 interview rounds.
I applied via Walk-in and was interviewed before Aug 2020. There was 1 interview round.
I applied via Approached by Company and was interviewed before Feb 2021. There were 3 interview rounds.
I applied via Approached by Company and was interviewed before Jun 2022. There were 5 interview rounds.
Sub cooling in air conditioning is the process of cooling the refrigerant below its saturation temperature to improve system efficiency.
Sub cooling increases the efficiency of the air conditioning system by ensuring the refrigerant is in a liquid state before entering the expansion valve.
It helps in preventing flash evaporation of the refrigerant, which can lead to inefficiencies in the system.
Sub cooling is typically ...
ISEER rating is calculated based on the weighted average of the cooling performance of an air conditioner under different conditions.
ISEER = (Weighted Cooling Capacity at 100% load x 0.4) + (Weighted Cooling Capacity at 75% load x 0.2) + (Weighted Cooling Capacity at 50% load x 0.4)
The higher the ISEER rating, the more energy efficient the air conditioner is.
ISEER rating helps consumers compare the energy efficiency of...
The refrigeration cycle is a thermodynamic cycle used in refrigerators and air conditioning systems to transfer heat from a low temperature to a high temperature environment.
The cycle consists of four main components: compressor, condenser, expansion valve, and evaporator.
The refrigerant enters the compressor as a low-pressure gas and leaves as a high-pressure, high-temperature gas.
The high-pressure gas then flows into...
Mainstream refrigerants used in household air conditioning include R-410A, R-22, and R-134a.
R-410A is a popular refrigerant known for its high efficiency and environmental friendliness.
R-22, although being phased out due to its ozone-depleting properties, is still commonly found in older air conditioning systems.
R-134a is commonly used in automotive air conditioning systems but can also be found in some household units
1 ton cooling concept refers to the amount of heat required to melt one ton of ice in a 24-hour period.
1 ton of cooling is equal to 12,000 BTUs per hour
It is commonly used in the HVAC industry to measure the cooling capacity of air conditioning systems
For example, a 2-ton air conditioner can remove 24,000 BTUs of heat per hour
The relationship between current, voltage, and power is described by Ohm's Law, which states that current is directly proportional to voltage and inversely proportional to resistance.
Ohm's Law states that V = I * R, where V is voltage, I is current, and R is resistance.
Power (P) is calculated using the formula P = V * I, where P is power, V is voltage, and I is current.
In a circuit with a constant resistance, an increa...
1 BTU is approximately equal to 0.29307107 watts. To convert BTU to watts, multiply by 0.29307107. To convert watts to BTU, divide by 0.29307107.
1 BTU = 0.29307107 watts
To convert BTU to watts, multiply by 0.29307107
To convert watts to BTU, divide by 0.29307107
Generic leetcode easy medium
based on 1 interview
Interview experience
based on 1 review
Rating in categories
Sales Executive
187
salaries
| ₹0 L/yr - ₹0 L/yr |
Area Sales Manager
80
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Software Engineer
68
salaries
| ₹0 L/yr - ₹0 L/yr |
Technical Support Engineer
56
salaries
| ₹0 L/yr - ₹0 L/yr |
Software Engineer
53
salaries
| ₹0 L/yr - ₹0 L/yr |
Samsung
LG Electronics
Panasonic Avionics Corporation
Toshiba