Upload Button Icon Add office photos

Filter interviews by

Saurashtra Chemicals Graduate Engineer Trainee (Get) Interview Questions and Answers

Updated 12 Jan 2023

Saurashtra Chemicals Graduate Engineer Trainee (Get) Interview Experiences

3 interviews found

Interview experience
4
Good
Difficulty level
Hard
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in Dec 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Principles and Working of different types of Instrumentation
  • Ans. 

    Instrumentation principles and working involve measurement, control, and automation of various physical variables.

    • Instrumentation involves the use of sensors, transducers, and signal processing equipment to measure and control physical variables such as temperature, pressure, flow, and level.

    • Different types of instrumentation include analog and digital instruments, pneumatic and electronic instruments, and smart instru...

  • Answered by AI
Round 3 - HR 

(1 Question)

  • Q1. Location and salary discussion

Interview Preparation Tips

Interview preparation tips for other job seekers - Basic knowledge of Process Instrumentation from Engineering, Transducers and Process Measurement book can be referred before interview

I applied via Campus Placement and was interviewed in Aug 2021. There were 3 interview rounds.

Interview Questionnaire 

3 Questions

  • Q1. About types of Heat exchanger and working principle
  • Q2. About NPSH And heat transfer coefficient
  • Q3. About LMTD in heat transfer

Interview Preparation Tips

Interview preparation tips for other job seekers - Be patient and hear properly and answer

Graduate Engineer Trainee (Get) Interview Questions Asked at Other Companies

asked in JBM Group
Q1. Q: 1 What is IC engine? What is the types of IC engine? Q:2 Diffe ... read more
Q2. How to check for continuity for a wire inside a wall if the start ... read more
Q3. What will be the cost of painting the wall behind me?
Q4. What happen when there is large air void in concrete?
Q5. What are the different types of concrete?

Interview Questionnaire 

1 Question

  • Q1. Different parts of pumps.
  • Ans. 

    Different parts of pumps include impeller, casing, shaft, bearings, and seals.

    • Impeller: rotates to create suction and discharge pressure

    • Casing: contains the impeller and directs the flow of fluid

    • Shaft: connects the impeller to the motor

    • Bearings: support the shaft and reduce friction

    • Seals: prevent fluid from leaking out of the pump

  • Answered by AI

Interview questions from similar companies

Interview Questionnaire 

3 Questions

  • Q1. Tell me something which is not there in resume?
  • Q2. What did you learn in internship?
  • Q3. Current affairs related questions.

Interview Preparation Tips

Interview preparation tips for other job seekers - Most of the questions were based on your resume. So be very clear and concise while speaking about what mentioned in resume.

I applied via Campus Placement and was interviewed before Nov 2020. There were 4 interview rounds.

Interview Questionnaire 

2 Questions

  • Q1. General basic departmental ques.
  • Q2. If you are chemical engineer...grap basic knowledge of heat..fluid and mass

Interview Preparation Tips

Interview preparation tips for other job seekers - Focus on general interview ques from Google like about pump,valve,heat transfer etc
Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Aptitude Test 

Online test on technical and aptitude with maths

Round 2 - Technical 

(2 Questions)

  • Q1. Your favorite subject
  • Q2. What have you learned in your training
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via Campus Placement and was interviewed in Apr 2024. There were 2 interview rounds.

Round 1 - Aptitude Test 

Domain based questions and basic aptitude question

Round 2 - Technical 

(5 Questions)

  • Q1. About distillation column, basic questions ,cooling tower concept.
  • Q2. Difference between CSTR and PFR, Pumps ,Heat Exchanger.
  • Ans. 

    CSTR and PFR are types of reactors, pumps are used to move fluids, heat exchangers transfer heat between fluids.

    • CSTR (Continuous Stirred Tank Reactor) has a constant volume and operates under steady-state conditions.

    • PFR (Plug Flow Reactor) has a varying volume and operates under unsteady-state conditions.

    • Pumps are mechanical devices used to move fluids from one place to another, like centrifugal pumps or positive displ...

  • Answered by AI
  • Q3. What is cracking
  • Ans. 

    Cracking is a process in which complex hydrocarbon molecules are broken down into simpler molecules.

    • Cracking is a refining process used to convert large hydrocarbon molecules into smaller, more valuable ones.

    • It is done by breaking the carbon-carbon bonds in the molecules.

    • Examples include catalytic cracking and steam cracking.

  • Answered by AI
  • Q4. What is Reforming
  • Ans. 

    Reforming is a process used in the petroleum industry to convert low-octane naphtha into high-octane gasoline.

    • Reforming involves rearranging the molecular structure of hydrocarbons to increase their octane rating.

    • It is typically done using a catalyst at high temperatures and pressures.

    • The process can also produce hydrogen gas as a byproduct.

    • Reforming is an important step in the production of gasoline and other fuels in...

  • Answered by AI
  • Q5. What is range and approach of cooling tower
  • Ans. 

    The range of a cooling tower refers to the maximum distance at which it can effectively cool air, while the approach is the temperature difference between the cooled water and the entering air.

    • Range of a cooling tower is typically around 5-20 degrees Fahrenheit

    • Approach of a cooling tower is usually around 8-15 degrees Fahrenheit

    • The range and approach of a cooling tower can vary based on factors such as design, size, an

  • Answered by AI

Interview Preparation Tips

Topics to prepare for Tata Chemicals Graduate Engineer Trainee (Get) interview:
  • Distillation Column
  • Heat Exchangers
  • Pumps
  • Cooling Tower
Interview preparation tips for other job seekers - Have Patience
Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(2 Questions)

  • Q1. Instrumentation
  • Q2. Conrol systems

I applied via Campus Placement and was interviewed in Feb 2021. There were 4 interview rounds.

Interview Questionnaire 

6 Questions

  • Q1. Draw simply supported beam with uniform load distribution(strength of materials)
  • Ans. 

    Drawing a simply supported beam with uniform load distribution in strength of materials.

    • Draw a straight line representing the beam.

    • Mark the supports at both ends of the beam.

    • Draw arrows representing the uniform load distribution on the beam.

    • Calculate the reactions at the supports using equations of equilibrium.

    • Draw the shear force and bending moment diagrams for the beam.

    • Calculate the maximum shear force and bending mo...

  • Answered by AI
  • Q2. About equation of power of centrifugal pump.
  • Q3. What is pressure and velocity compounding.
  • Ans. 

    Pressure and velocity compounding are methods used to increase the efficiency of steam turbines.

    • Pressure compounding involves dividing the pressure drop across the turbine into smaller stages, each with its own set of moving blades.

    • Velocity compounding involves dividing the steam flow into smaller streams, each flowing through a set of fixed blades.

    • Both methods increase the efficiency of the turbine by reducing the amo...

  • Answered by AI
  • Q4. Tell me about iron-iron carbide diagram
  • Ans. 

    Iron-iron carbide diagram is a graphical representation of the phases of iron and carbon at different temperatures and compositions.

    • Also known as the Fe-C diagram

    • Shows the transformation of iron from ferrite to austenite to pearlite

    • Used to determine the microstructure and properties of steel

    • Helps in designing heat treatment processes for steel

    • Important tool for metallurgists and materials engineers

  • Answered by AI
  • Q5. Tell me normalizing, annealing, and hardening processes.
  • Ans. 

    Normalizing, annealing, and hardening are heat treatment processes used to alter the properties of metals.

    • Normalizing involves heating the metal to a temperature above its critical point and then cooling it in air. This process improves the strength and toughness of the metal.

    • Annealing involves heating the metal to a specific temperature and then cooling it slowly. This process reduces the hardness and increases the du...

  • Answered by AI
  • Q6. Formula of efficiency of Rankine cycle.
  • Ans. 

    Efficiency of Rankine cycle formula.

    • Efficiency = (Net work output / Heat input)

    • Efficiency = (1 - T2/T1)

    • T1 is the temperature of steam at the inlet of turbine

    • T2 is the temperature of steam at the outlet of turbine

    • Net work output = (P1 - P2) * (V2 - V1)

    • Heat input = m * (h1 - h2)

    • m is the mass flow rate of steam

    • h1 is the enthalpy of steam at the inlet of turbine

    • h2 is the enthalpy of steam at the outlet of turbine

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - i applied through campus placement
1st (round is online written test ( all questions are previous year gate exams)
2nd ( round is technical + hr interview )
be patient because it takes 3-4 month to get answer from company
and selection ratio is 10:1
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
Selected Selected

I applied via Campus Placement and was interviewed before Mar 2023. There were 2 interview rounds.

Round 1 - Group Discussion 

A topic was given on which all of us have to provide views, GD was good and each of us of shared some strong points.

Round 2 - One-on-one 

(1 Question)

  • Q1. Since it is a supply chain, describe how you are suitable candidate as there is no specific supply chain internship
  • Ans. 

    I have a strong academic background in engineering and relevant skills such as problem-solving, analytical thinking, and attention to detail.

    • I have completed coursework in logistics and supply chain management during my engineering degree.

    • I have participated in projects that involved optimizing supply chain processes and improving efficiency.

    • I have experience working with inventory management systems and analyzing data...

  • Answered by AI

Saurashtra Chemicals Interview FAQs

How many rounds are there in Saurashtra Chemicals Graduate Engineer Trainee (Get) interview?
Saurashtra Chemicals interview process usually has 3 rounds. The most common rounds in the Saurashtra Chemicals interview process are Resume Shortlist, Technical and HR.
What are the top questions asked in Saurashtra Chemicals Graduate Engineer Trainee (Get) interview?

Some of the top questions asked at the Saurashtra Chemicals Graduate Engineer Trainee (Get) interview -

  1. Principles and Working of different types of Instrumentat...read more
  2. Different parts of pum...read more
  3. About types of Heat exchanger and working princi...read more

Tell us how to improve this page.

Saurashtra Chemicals Graduate Engineer Trainee (Get) Interview Process

based on 1 interview

Interview experience

4
  
Good
View more
Saurashtra Chemicals Graduate Engineer Trainee (Get) Salary
based on 11 salaries
₹2.3 L/yr - ₹2.5 L/yr
35% less than the average Graduate Engineer Trainee (Get) Salary in India
View more details

Saurashtra Chemicals Graduate Engineer Trainee (Get) Reviews and Ratings

based on 5 reviews

3.2/5

Rating in categories

2.9

Skill development

3.5

Work-life balance

2.1

Salary

4.8

Job security

1.9

Company culture

2.3

Promotions

2.8

Work satisfaction

Explore 5 Reviews and Ratings
Mechanical Engineer
38 salaries
unlock blur

₹2.4 L/yr - ₹7.8 L/yr

Mechanical Maintenance Engineer
20 salaries
unlock blur

₹2.3 L/yr - ₹7.4 L/yr

Electrical Engineer
20 salaries
unlock blur

₹2.6 L/yr - ₹6.2 L/yr

Engineer
16 salaries
unlock blur

₹2.3 L/yr - ₹5.3 L/yr

Maintenance Engineer
16 salaries
unlock blur

₹2.4 L/yr - ₹5 L/yr

Explore more salaries
Compare Saurashtra Chemicals with

Berger Paints

3.7
Compare

Pidilite Industries

4.3
Compare

SRF

4.1
Compare

Kansai Nerolac Paints

3.8
Compare
Did you find this page helpful?
Yes No
write
Share an Interview