Add office photos
i
Presto Stantest
Compare
Filter interviews by
Presto Stantest Interview Questions and Answers
Presto Stantest Interview Experiences
3 interviews found
Selected
I applied via Walk-in and was interviewed in Sep 2022. There were 4 interview rounds.
(2 Questions)
- Q1. Introduction of yourself
- Ans. Step to introduce yourself 1 Name 2. Education qualification from higher to low 3 Family background 4 Interest/ hobby
- Q2. Why did you left your last company
- Ans. It totally depends upon you.But in my case was the night shift timing which was affecting my health so I left the job.
(3 Questions)
- Q1. What is called an Electricity?
- Ans.
Electricity is the flow of electrons through a conductor.
Electricity is a form of energy that powers most of our modern devices.
It is created by the movement of electrons from one atom to another.
Electricity can be generated by various sources such as coal, wind, solar, and hydro power.
It can be dangerous if not handled properly and can cause electric shock or fire.
Electricity is measured in units of volts, amps, and w
- Q2. What is the difference between AC and DC current?
- Ans.
AC current changes direction periodically while DC current flows in one direction only.
AC current is used in household appliances and power grids while DC current is used in batteries and electronic devices.
AC current can be easily transformed into different voltages while DC current cannot be transformed easily.
AC current is more dangerous to humans than DC current due to its ability to cause muscle contractions.
DC cu...
- Q3. What are transformer?
- Ans.
Transformers are electrical devices that transfer energy from one circuit to another through electromagnetic induction.
Transformers are used to increase or decrease the voltage of an alternating current (AC) power supply.
They consist of two coils of wire, known as the primary and secondary coils, which are wrapped around a magnetic core.
When an AC voltage is applied to the primary coil, it creates a magnetic field that...
(3 Questions)
- Q1. Why do you want to join this company?
- Ans. I want to gain knowledge in different fields.Although I have done diploma in Electrical trade but I was not getting any job in this field so I worked in it field and gained knowledge in IT field now since I got the opportunity to work in my field I want to enhance my knowledge in this field.
- Q2. What is your expected salary?
- Q3. If I get the salary that I used to get in my last company also I am ready to work.
Interview Preparation Tips
L2 Technical Support Engineer Interview Questions asked at other Companies
Selected
I applied via Recruitment Consulltant and was interviewed before Nov 2023. There was 1 interview round.
(1 Question)
- Q1. Experience, current salary, expectation, location, recruitment experience?
Interview Preparation Tips
Assistant Manager- HR Interview Questions asked at other Companies
I applied via Company Website and was interviewed in May 2021. There were 3 interview rounds.
Interview Questionnaire
2 Questions
- Q1. About ur last company
- Q2. About ur self
Interview Preparation Tips
Service Engineer Interview Questions asked at other Companies
Jobs at Presto Stantest
Top trending discussions
Interview questions from similar companies
I was interviewed in Nov 2024.
(4 Questions)
- Q1. Wind calculation as per IS code
- Ans.
The procedure for wind calculation as per IS code involves determining the design wind speed, selecting the appropriate terrain category, and calculating the wind pressure.
Determine the design wind speed based on the location and height of the structure.
Select the appropriate terrain category (rural, urban, etc.) as per IS code guidelines.
Calculate the wind pressure using the formula provided in the IS code.
Consider fa...
- Q2. SFD and BMD of cantilever beam
- Q3. Staad model for fixed pole
- Ans.
A STAAD model for a fixed pole is a structural analysis and design model used to determine the stability and strength of a pole that is fixed in place.
In a STAAD model for a fixed pole, the pole is typically modeled as a vertical member with fixed supports at the base.
The model considers factors such as wind loads, dead loads, and any other relevant loads that may act on the pole.
The analysis helps in determining the s...
- Q4. Design of Square base plate
- Ans.
Key considerations in designing a square base plate
Ensure the base plate is large enough to support the load without excessive deflection
Select appropriate material and thickness to meet structural requirements
Consider the connection details for attaching the base plate to the structure
Account for any potential corrosion or environmental factors that may affect the base plate
Include provisions for anchor bolts or other...
Interview Preparation Tips
Selected
I applied via Referral and was interviewed in Dec 2024. There was 1 interview round.
(2 Questions)
- Q1. Witch type transformer use in elevator?
- Q2. Difference in open loop or close loop
Junior Engineer - mould Maintenance Interview Questions & Answers
Tokai Rubber Auto Parts India
Anonymous
posted on 28 Jul 2022
Selected
I applied via Recruitment Consulltant and was interviewed before Jul 2021. There was 1 interview round.
(3 Questions)
- Q1. Group discussion
- Q2. Hr round and discussion
- Q3. Technical round and injection moulding related any questions
Interview Preparation Tips
- Injection Moulding
Design Engineer Interview Questions & Answers
Crane Process Flow Technologies India
Vrushabh Chute
posted on 11 Jan 2025
(2 Questions)
- Q1. Questions related to core mechanical engg
- Q2. Product related questions
Cable selection
Panel components mounting
Panel layout?
(2 Questions)
- Q1. Latest working version of Eplan
- Q2. Eplan command
Interview Preparation Tips
(3 Questions)
- Q1. Manufacturing department
- Q2. Manpower handle
- Q3. Daily target production
Interview Preparation Tips
(1 Question)
- Q1. How does a CNC machine works?
- Ans.
A CNC machine works by using computer programs to control the movement of the machine's tools and workpiece to create precision parts.
CNC machines use computer programs to control the movement of the cutting tools and workpiece.
The programs are created using CAD/CAM software and converted into G-code instructions.
The machine reads the G-code instructions and moves the tools along the specified paths to cut and shape th...
Presto Stantest Interview FAQs
Tell us how to improve this page.
Interview Questions for Popular Designations
- Executive Interview Questions
- Team Lead Interview Questions
- Software Developer Interview Questions
- Associate Software Engineer Interview Questions
- Accountant Interview Questions
- Data Analyst Interview Questions
- Senior Software Engineer Interview Questions
- System Engineer Interview Questions
- Show more
People are getting interviews through
Interview Questions from Similar Companies
Presto Stantest Reviews and Ratings
based on 84 reviews
Rating in categories
3-4 Yrs
₹ 7-10 LPA
5-8 Yrs
₹ 10-17 LPA
5-6 Yrs
₹ 10-12 LPA
|
Service Engineer
20
salaries
|  ₹2.5 L/yr - ₹4 L/yr |
|
Sales Coordinator
12
salaries
| ₹2 L/yr - ₹3.9 L/yr |
|
Assistant Sales Manager
7
salaries
| ₹4.5 L/yr - ₹6.6 L/yr |
|
Technical Support Engineer
7
salaries
| ₹2 L/yr - ₹3.8 L/yr |
|
Quality Engineer
6
salaries
| ₹2.6 L/yr - ₹3.6 L/yr |
TCS
Infosys
Wipro
HCLTech
Calculate your in-hand salary
- Home >
- Interviews >
- Presto Stantest Interview Questions
