Faster and better experience!
Filter interviews by
I applied via Walk-in and was interviewed in Jun 2024. There was 1 interview round.
A single line diagram of a VFD shows the electrical connections and components in a simplified format.
Shows the power supply, VFD unit, motor, and control devices in a single line format
Used for easy understanding of the electrical connections and components
Does not show the physical layout or exact wiring details
Top trending discussions
I applied via Naukri.com and was interviewed before Oct 2021. There were 2 interview rounds.
I applied via Company Website and was interviewed in Jul 2021. There were 3 interview rounds.
EOt crane is an electric overhead traveling crane used for lifting and moving heavy loads in industrial settings.
EOt stands for Electric Overhead Traveling
It is operated by an electrical control system
It consists of a bridge, hoist, trolley, and electrical components
It is commonly used in factories, warehouses, and construction sites
It can lift and move heavy loads up to several tons
It requires regular maintenance and
posted on 2 Sep 2023
posted on 29 Nov 2022
I applied via Walk-in and was interviewed in May 2022. There was 1 interview round.
The capacity of a furnace refers to its heating output, typically measured in BTUs or tons.
Furnace capacity is determined by the amount of heat it can produce.
It is usually measured in BTUs (British Thermal Units) or tons.
Higher capacity furnaces can produce more heat and are suitable for larger spaces.
For example, a furnace with a capacity of 80,000 BTUs can heat a larger area compared to one with a capacity of 40,000
Drive components in CCM department are the parts that enable the motor to function properly.
Drive components include motors, gears, belts, and pulleys.
They work together to transfer power from the motor to the machine.
The components must be properly sized and aligned to ensure efficient operation.
Examples of machines that use drive components include conveyor belts, pumps, and fans.
Control diagram of a motor with remote and local start using star delta starter.
Use a star delta starter for reduced voltage starting
Include a remote start/stop switch in the control circuit
Use a contactor to switch between star and delta connections
Include overload protection in the circuit
Use a control transformer to step down voltage for control circuit
Include a pilot light to indicate motor status
I appeared for an interview in Jan 2024.
Power factor is the ratio of real power to apparent power in an AC circuit. VFD stands for Variable Frequency Drive. AC motors run on alternating current while DC motors run on direct current.
Power factor is a measure of how effectively electrical power is being used in a circuit.
It is calculated by dividing the real power (in watts) by the apparent power (in volt-amperes).
A power factor of 1 indicates that all the pow...
Types of load cells include strain gauge load cells, hydraulic load cells, and capacitive load cells.
Strain gauge load cells measure the strain or deformation of a material.
Hydraulic load cells use hydraulic fluid to measure force.
Capacitive load cells measure changes in capacitance to determine force.
Other types of load cells include piezoelectric load cells and pneumatic load cells.
I applied via Referral and was interviewed before May 2023. There were 3 interview rounds.
MCQ Question of total 10 question
Reverse arc flashing on ACB breaker refers to the phenomenon where the arc flash occurs on the opposite side of the contacts during the opening operation.
Reverse arc flashing happens when the arc flash occurs on the side of the contacts opposite to the normal direction during the opening operation of the ACB breaker.
This phenomenon can be caused by factors such as high fault currents, improper maintenance, or inadequat...
I applied via Recruitment Consulltant and was interviewed before Aug 2022. There were 3 interview rounds.
Cold rolling mill uses pressure to reduce the thickness of metal sheets by passing them through rollers.
Metal sheets are passed through rollers under high pressure to reduce thickness
Rollers can be adjusted to achieve desired thickness and surface finish
Cold rolling process increases strength and hardness of metal sheets
Common metals processed in cold rolling mills include steel, aluminum, and copper
I applied via Recruitment Consulltant and was interviewed before Sep 2020. There were 3 interview rounds.
Physical and chemical quality of raw materials and sinter product is crucial for ensuring product quality and performance.
Raw materials should meet specified physical and chemical requirements to ensure desired sinter product properties.
Regular testing and analysis of raw materials and sinter product is necessary to maintain quality standards.
Factors such as particle size, composition, moisture content, and impurities ...
based on 1 interview
Interview experience
based on 3 reviews
Rating in categories
Assistant Manager
15
salaries
| ₹3.6 L/yr - ₹6 L/yr |
Mechanical Engineer
9
salaries
| ₹3 L/yr - ₹5.5 L/yr |
Engineer
8
salaries
| ₹3.7 L/yr - ₹5 L/yr |
Executive Engineer
6
salaries
| ₹1.6 L/yr - ₹4.2 L/yr |
Shift Incharge
6
salaries
| ₹1.1 L/yr - ₹3.6 L/yr |
Tata Steel
JSW Steel
Jindal Stainless
Jindal Saw