Upload Button Icon Add office photos

NMDC Limited

Compare button icon Compare button icon Compare

Filter interviews by

NMDC Limited Junior Associate Interview Questions and Answers

Updated 18 Mar 2024

NMDC Limited Junior Associate Interview Experiences

1 interview found

Interview experience
3
Average
Difficulty level
Hard
Process Duration
Less than 2 weeks
Result
Not Selected

I applied via Campus Placement and was interviewed in Feb 2024. There were 2 interview rounds.

Round 1 - Assignment 

Angles and calculations

Round 2 - Technical 

(1 Question)

  • Q1. Orthographic views and conversions

Interview Preparation Tips

Interview preparation tips for other job seekers - Just study the material which was given by college people

Interview questions from similar companies

Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(4 Questions)

  • Q1. Question regarding motor, generator, Alternator and transformer.
  • Q2. What are causes of hot bearings?
  • Ans. 

    Causes of hot bearings include lack of lubrication, overloading, misalignment, and contamination.

    • Lack of lubrication: Insufficient or degraded lubricant can cause increased friction and heat.

    • Overloading: Excessive load on the bearing can lead to overheating.

    • Misalignment: Improper alignment of the bearing can cause it to operate under stress and generate heat.

    • Contamination: Foreign particles or debris in the bearing can

  • Answered by AI
  • Q3. What causes are responsible for over-heating of Commutator in a DC motor?
  • Ans. 

    Over-heating of Commutator in a DC motor can be caused by factors like excessive current, poor ventilation, dirty environment, and worn-out brushes.

    • Excessive current flowing through the motor can cause the commutator to overheat.

    • Poor ventilation around the motor can lead to inadequate cooling, resulting in overheating.

    • A dirty environment can cause dust and debris to accumulate on the commutator, hindering heat dissipat...

  • Answered by AI
  • Q4. What will happen if a shunt motor is directly connected to the supply line?
  • Ans. 

    The shunt motor will run at dangerously high speeds and may get damaged.

    • The motor will run at its no-load speed, which is much higher than its rated speed.

    • This can lead to overheating and mechanical stress on the motor components.

    • The motor may get damaged or fail prematurely if directly connected to the supply line.

  • Answered by AI
Round 3 - Technical 

(1 Question)

  • Q1. Question related to motor, generator Alternator and transformer

Interview Preparation Tips

Interview preparation tips for other job seekers - Good knowledge regarding electrical machine.

Junior Officer Interview Questions & Answers

Nalco user image SUMANTA KISHORE RAY

posted on 28 Sep 2023

Interview experience
4
Good
Difficulty level
Moderate
Process Duration
-
Result
Selected Selected

I applied via Referral and was interviewed in Aug 2023. There were 4 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all tips
Round 2 - Aptitude Test 

Written test on general knowledge

Round 3 - Personal Interview 

(1 Question)

  • Q1. It was on education, general knowledge and on stores and purchase functions.
Round 4 - No 

(1 Question)

  • Q1. There was no round 3 interview

Interview Preparation Tips

Interview preparation tips for other job seekers - This was conducted in 1984. It was very simple. It was having an aptitude test followed by an interview
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in Aug 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Properly align and format text in your resume. A recruiter will have to spend more time reading poorly aligned text, leading to high chances of rejection.
View all tips
Round 2 - Technical 

(4 Questions)

  • Q1. Types of compressor Working of compressor
  • Ans. 

    Compressors are devices that increase the pressure of a gas or vapor.

    • Types of compressors include reciprocating, rotary screw, centrifugal, and axial flow compressors.

    • Reciprocating compressors use pistons to compress gas, while rotary screw compressors use screws.

    • Centrifugal compressors use a rotating impeller to increase gas velocity, while axial flow compressors use blades to compress gas.

    • Compressors work by reducing...

  • Answered by AI
  • Q2. Pump working functions Winder engine part name
  • Ans. 

    Pump working functions involve moving fluids from one place to another. Winder engine part name varies depending on the type of engine.

    • Pump working functions include suction, discharge, and pressure generation.

    • Winder engine part names can include crankshaft, camshaft, piston, and connecting rod.

    • Examples of pumps include centrifugal pumps, positive displacement pumps, and jet pumps.

  • Answered by AI
  • Q3. How to start compressor On/off switch
  • Ans. 

    To start a compressor, turn on the on/off switch and wait for the compressor to build up pressure.

    • Locate the on/off switch on the compressor.

    • Turn the switch to the 'on' position.

    • Wait for the compressor to build up pressure before using it.

    • If the compressor has a pressure gauge, wait for it to reach the desired pressure level before using it.

    • If the compressor has a safety valve, make sure it is not open before starting

  • Answered by AI
  • Q4. Electric supply Transformer

Interview Preparation Tips

Topics to prepare for MOIL Junior Engineer interview:
  • Working principal
Interview preparation tips for other job seekers - Take some knowledge about your company
Technical strong about your department some basic question learn them
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Company Website and was interviewed in Jul 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Double-check your resume for any spelling mistakes. The recruiter may consider spelling mistakes as careless behavior or poor communication skills.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. What is 5S,TPM,7 Qc tools ?
  • Ans. 

    5S, TPM, and 7 QC tools are methodologies used in manufacturing to improve efficiency and quality.

    • 5S is a workplace organization method that involves sorting, simplifying, sweeping, standardizing, and sustaining.

    • TPM stands for Total Productive Maintenance and is a system for maintaining and improving equipment and processes.

    • 7 QC tools are a set of problem-solving tools used to identify and solve quality-related issues....

  • Answered by AI
  • Q2. Knowledge of Battery Assembly
Round 3 - HR 

(2 Questions)

  • Q1. Whats your current salary ?
  • Q2. How much you expect from here ?

Interview Preparation Tips

Topics to prepare for Kalyani Group Junior Engineer interview:
  • Battery Domain
Interview preparation tips for other job seekers - where you work,give your best ..Take proper knowledge of it.

I applied via Company Website and was interviewed in Apr 2022. There was 1 interview round.

Round 1 - Technical 

(4 Questions)

  • Q1. Say something about press filter
  • Ans. 

    Press filter is a device used for separating solids from liquids.

    • It works by applying pressure to the mixture to force the liquid through a filter media while retaining the solids.

    • It is commonly used in industries such as chemical, pharmaceutical, and food processing.

    • Examples of press filters include belt filter press, plate and frame filter press, and rotary vacuum-drum filter.

    • Press filters are efficient and cost-effe...

  • Answered by AI
  • Q2. How to maintain pressure in press filter
  • Ans. 

    To maintain pressure in press filter, ensure proper sealing, check for leaks, and adjust feed rate and pressure settings.

    • Check for proper sealing of the filter plates and gaskets

    • Inspect for any leaks in the system and repair them promptly

    • Adjust the feed rate and pressure settings as per the manufacturer's recommendations

    • Regularly clean and maintain the filter to prevent clogging and pressure drop

    • Monitor the pressure ga...

  • Answered by AI
  • Q3. What is the model of hydraulic cylinder in press filter
  • Ans. 

    The model of hydraulic cylinder in press filter depends on the specific press filter being used.

    • The model of hydraulic cylinder can vary depending on the size and capacity of the press filter.

    • Some common models of hydraulic cylinders used in press filters include tie rod cylinders and welded cylinders.

    • The specific model of hydraulic cylinder used in a press filter can be determined by consulting the manufacturer's spec...

  • Answered by AI
  • Q4. Which type bearing use in bogie wheel
  • Ans. 

    Roller bearings are commonly used in bogie wheels.

    • Roller bearings are preferred over plain bearings due to their ability to handle heavy loads and reduce friction.

    • Tapered roller bearings are commonly used in locomotive bogie wheels.

    • Cylindrical roller bearings are also used in some bogie wheels.

    • The type of bearing used depends on the specific application and load requirements.

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Focus on those jobs that you meet the minimum requirements for, you should match the mejority of the keywords in the job description.
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Company Website and was interviewed before Feb 2023. There was 1 interview round.

Round 1 - One-on-one 

(2 Questions)

  • Q1. Previous work experience
  • Q2. How is gratuity calculated
  • Ans. 

    Gratuity is calculated based on an employee's length of service and last drawn salary.

    • Gratuity is a lump sum amount paid to an employee as a token of appreciation for their service.

    • The calculation of gratuity depends on the number of years an employee has worked for an organization.

    • In India, gratuity is calculated using the formula: (Last drawn salary × 15 × number of years of service) / 26.

    • The number of years of servi...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - There was only one round. Since mine was HR Profile, they asked questions related to Industrial Relations, Compensation acts and recruitment
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Do not use an unprofessional email address such as cool_boy@email.com. It shows a lack of professionalism by the candidate.
View all tips
Round 2 - Technical 

(3 Questions)

  • Q1. What are the Self motor
  • Ans. 

    Self motor is not a commonly used term in electrical engineering.

    • It is possible that the interviewer meant to ask about self-starting motors, which are motors that can start without external assistance.

    • Another possibility is that they were referring to self-excited motors, which generate their own magnetic field without the need for a separate excitation source.

    • It is important to clarify the question with the interview

  • Answered by AI
  • Q2. What are thae Altnater
  • Ans. 

    Alternators are electrical generators that convert mechanical energy into electrical energy.

    • Alternators are commonly used in vehicles to charge the battery and power the electrical system.

    • They work by using a rotating magnetic field to induce an electrical current in a stationary coil of wire.

    • Alternators are more efficient and reliable than traditional generators.

    • They are also smaller and lighter, making them ideal for...

  • Answered by AI
  • Q3. What are the Battery
  • Ans. 

    Batteries are devices that store chemical energy and convert it into electrical energy.

    • Batteries come in various sizes and types, including alkaline, lithium-ion, and lead-acid.

    • They are commonly used in electronic devices, vehicles, and backup power systems.

    • Batteries have a positive and negative terminal, and the flow of electrons between them creates an electrical current.

    • The capacity of a battery is measured in amper

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Best question super ready hr around
Interview experience
1
Bad
Difficulty level
Easy
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Naukri.com and was interviewed in Aug 2023. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Be truthful in your resume. It is very easy to catch false or lies during the interview by asking basic questions.
View all tips
Round 2 - One-on-one 

(2 Questions)

  • Q1. Building construction
  • Q2. Road construction

Interview Preparation Tips

Interview preparation tips for other job seekers - One time and Crack small time very important

I applied via Naukri.com and was interviewed in Nov 2022. There were 4 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Be honest with your years of experience. All information you share will be verified at the time of joining.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Related our Work experience
Round 3 - One-on-one 

(1 Question)

  • Q1. Related our Qualification
Round 4 - Group Discussion 

Related our behaviour and future plan or policy

Interview Preparation Tips

Interview preparation tips for other job seekers - I want to share that anyone is preparing of job interview please first clear your base of knowledge and take a free mindset

NMDC Limited Interview FAQs

How many rounds are there in NMDC Limited Junior Associate interview?
NMDC Limited interview process usually has 2 rounds. The most common rounds in the NMDC Limited interview process are Assignment and Technical.

Tell us how to improve this page.

NMDC Limited Junior Associate Interview Process

based on 1 interview

Interview experience

3
  
Average
View more

Interview Questions from Similar Companies

Tata Steel Interview Questions
4.1
 • 855 Interviews
Bharat Petroleum Interview Questions
4.2
 • 148 Interviews
Metso Interview Questions
4.3
 • 65 Interviews
View all
Executive
146 salaries
unlock blur

₹7 L/yr - ₹14 L/yr

Executive Engineer
51 salaries
unlock blur

₹6 L/yr - ₹12.2 L/yr

Manager
37 salaries
unlock blur

₹9.4 L/yr - ₹30 L/yr

Senior Manager
37 salaries
unlock blur

₹13 L/yr - ₹40 L/yr

Deputy Manager
32 salaries
unlock blur

₹8 L/yr - ₹24 L/yr

Explore more salaries
Compare NMDC Limited with

Coal India

4.0
Compare

Steel Authority Of India

4.1
Compare

Oil And Natural Gas Corporation

4.4
Compare

Bharat Petroleum

4.2
Compare
Did you find this page helpful?
Yes No
write
Share an Interview