i
MSPL
Filter interviews by
I applied via Walk-in and was interviewed in Nov 2022. There were 3 interview rounds.
The input value of an LT panel is the electrical power supply provided to the panel.
The input value of an LT panel is typically the voltage and current supplied by the electrical utility.
It can be AC (alternating current) or DC (direct current) depending on the application.
The input value may vary depending on the specific requirements of the electrical system.
For example, in a residential building, the input value of ...
PPE stands for Personal Protective Equipment.
PPE is equipment worn to minimize exposure to hazards that may cause serious workplace injuries or illnesses.
Examples of PPE include safety glasses, gloves, hard hats, respirators, and earplugs.
Employers are responsible for providing PPE to their employees and ensuring that it is properly used and maintained.
Employees must also be trained on how to properly use and care for
Resistance is measured in ohms.
Resistance is a property of an electrical component or material that opposes the flow of electric current.
The unit of measurement for resistance is the ohm (Ω).
Resistance can be measured using a multimeter or an ohmmeter.
For example, a resistor with a resistance value of 100 ohms would be written as 100Ω.
Work should be completely done in given time
Top trending discussions
posted on 5 May 2019
SLD stands for Single Line Diagram which is a graphical representation of an electrical system.
SLD shows the electrical components and their interconnections in a simplified manner.
Components include transformers, generators, circuit breakers, switches, etc.
It also shows the ratings, voltage levels, and protective devices used in the system.
SLD is used for design, operation, and maintenance of electrical systems.
It hel...
I applied via Campus Placement and was interviewed before Sep 2021. There were 3 interview rounds.
Follow RS Agarwal book
posted on 31 Jul 2021
I applied via Walk-in and was interviewed in Jul 2021. There was 1 interview round.
posted on 8 Jul 2024
Apitude round was conducted
Losses in transformer refer to energy losses that occur during the conversion of electrical energy from one voltage level to another.
There are two main types of losses in transformers: copper losses and iron losses.
Copper losses occur due to the resistance of the copper windings and are also known as I^2R losses.
Iron losses, also known as core losses, occur due to hysteresis and eddy current losses in the transformer c...
Power factor is the ratio of real power to apparent power in an electrical system, indicating the efficiency of power usage.
Power factor is important for measuring the efficiency of electrical systems.
A high power factor indicates efficient power usage, while a low power factor indicates wastage.
Improving power factor can reduce electricity costs and increase system capacity.
Power factor correction devices like capacit...
posted on 25 Oct 2024
I applied via Campus Placement and was interviewed in Sep 2024. There was 1 interview round.
Induction motor operates on the principle of electromagnetic induction, while synchronous motor operates at a constant speed determined by the frequency of the power supply.
Induction motor does not require any external excitation to run, while synchronous motor requires a separate DC power source for excitation.
Induction motor has a slightly lower efficiency compared to synchronous motor.
Synchronous motor is used in ap...
Transformer parts include core, windings, and insulation. It is used to step up or step down voltage in electrical systems.
Transformer parts: core, windings, insulation
Core: provides magnetic path for flux
Windings: primary and secondary coils
Insulation: prevents short circuits
Used to step up or step down voltage in electrical systems
posted on 6 Jan 2023
I was interviewed in Jul 2022.
IEC standards are guidelines for electrical installations to ensure safety and efficiency.
IEC 60364 is the main standard for electrical installations in buildings
IEC 60079 provides guidelines for electrical installations in hazardous areas
IEC 61892 provides guidelines for electrical installations on offshore structures
IEC 61439 provides guidelines for low-voltage switchgear and control gear assemblies
Adherence to IEC s...
I applied via Recruitment Consulltant and was interviewed in May 2022. There was 1 interview round.
A circuit is a closed loop of conductive material that allows electricity to flow. A switch is a device that controls the flow of electricity in a circuit.
A circuit is made up of a power source, conductive material, and a load.
Electricity flows from the power source through the conductive material and into the load.
A switch is used to open or close the circuit, controlling the flow of electricity.
Switches can be manual...
MCB is a type of source of electrical energy used for protection against overload and short circuit.
MCB stands for Miniature Circuit Breaker.
It is a device that automatically switches off the electrical circuit during abnormal conditions such as overload or short circuit.
MCBs are commonly used in residential, commercial, and industrial electrical installations.
They provide protection to electrical equipment and prevent...
I applied via LinkedIn and was interviewed in Jan 2023. There were 2 interview rounds.
SIEM is a security information and event management system that collects and analyzes security data. XDR is an advanced threat detection and response platform that goes beyond SIEM.
SIEM collects and analyzes security data from various sources such as firewalls, servers, and endpoints.
XDR uses advanced analytics and machine learning to detect and respond to threats across multiple endpoints and networks.
SIEM is focused ...
PAM stands for Privileged Access Management and PIM stands for Privileged Identity Management.
PAM is a security solution that manages and monitors privileged access to critical systems and data.
PIM is a security solution that manages and secures privileged identities, such as administrator accounts.
Both PAM and PIM are important for protecting against insider threats and external attacks.
Examples of PAM and PIM solutio
For example, a ₹10 LPA CTC could mean an in-hand salary of ₹70,000–₹75,000 per month, depending on deductions and benefits.
✨ 𝗣𝗿𝗼 𝗧𝗶𝗽: Always request a detailed salary structure during negotiations—it’s your roadmap to making informed decisions
𝗖𝗧𝗖 𝘃𝘀 𝗜𝗻-𝗛𝗮𝗻𝗱 𝗦𝗮𝗹𝗮𝗿𝘆: 𝗧𝗵𝗲 𝗥𝗲𝗮𝗹𝗶𝘁𝘆 𝗖𝗵𝗲𝗰𝗸 𝗘𝘃𝗲𝗿𝘆 𝗣𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹 𝗡𝗲𝗲𝗱𝘀!
We’ve all been there—excitedly discussing job offers and hearing about the impressive CTC (Cost to Company). But when payday arrives, you wonder
based on 1 interview
Interview experience
Assistant Manager
36
salaries
| ₹0 L/yr - ₹0 L/yr |
Deputy Manager
22
salaries
| ₹0 L/yr - ₹0 L/yr |
Engineer
17
salaries
| ₹0 L/yr - ₹0 L/yr |
Mechanical Engineer
15
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Engineer
14
salaries
| ₹0 L/yr - ₹0 L/yr |
Tata Group
Reliance Industries
Adani Group
Bharti Enterprises