AmbitionBox
Interview Questions
- Reviews
- Salaries
- Interview Questions
- About Company
- Benefits
- Jobs
- Office Photos
- Community
Add office photos
Filter interviews by
Isgec Hitachi Zosen Interview Questions and Answers
8 Interview questions
SMH can be calculated by dividing the total time taken to complete a task by the number of units produced.
SMH stands for Standard Minute Hour
It is used to measure the productivity of a worker or a machine
Formula: SMH = Total time taken to complete a task / Number of units produced
Example: If it takes 120 minutes to produce 100 units, then SMH = 1.2 minutes per unit
Weld deposition can be calculated by multiplying the weld bead cross-sectional area by the length of the weld.
Measure the cross-sectional area of the weld bead
Measure the length of the weld
Multiply the cross-sectional area by the length of the weld to get the weld deposition
Weld deposition can be expressed in cubic inches or cubic millimeters
5'S can be implemented in fabrication by organizing and optimizing the workspace.
Sort and remove unnecessary items from the workspace
Set in order the necessary items in a logical and efficient manner
Shine and clean the workspace regularly
Standardize the processes and procedures for maintaining the workspace
Sustain the improvements by continuously monitoring and improving the workspace
Example: Use shadow boards to ...
Efficiency of motor can be measured by conducting a load test and measuring the input and output power.
Conduct a load test by connecting the motor to a dynamometer
Measure the input power using a wattmeter
Measure the output power using a torque meter and a speedometer
Calculate the efficiency using the formula: Efficiency = (Output Power/Input Power) x 100%
Compare the calculated efficiency with the standard efficien...
A drive is a device that reads or writes data on a storage medium. Types include hard disk, solid-state, optical, and flash drives.
A drive is a hardware component that allows data to be stored and retrieved from a storage medium.
Hard disk drives use spinning disks to read and write data, while solid-state drives use flash memory.
Optical drives use lasers to read and write data on CDs, DVDs, and Blu-ray discs.
Flash...
The duty cycle of a power contractor refers to the amount of time it can operate continuously without overheating or needing to cool down.
The duty cycle is typically expressed as a percentage, representing the ratio of operating time to the total time.
For example, a power contractor with a duty cycle of 50% can operate for 5 minutes and then needs to cool down for 5 minutes before being used again.
A higher duty cy...
To identify the type of breakdown in a solenoid valve, one can perform visual inspection, check for electrical continuity, and conduct voltage and resistance tests.
Perform a visual inspection to check for any visible signs of damage or wear on the solenoid valve.
Check for electrical continuity by using a multimeter to test the continuity between the electrical connections of the solenoid valve.
Conduct voltage test...
The max carrier frequency of Yaskawa A1000 is 16kHz. Department ISO objective and MD calculation time are not related to the product.
Max carrier frequency of Yaskawa A1000 is 16kHz
Department ISO objective is not related to the product
MD calculation time is not related to the product
Isgec Hitachi Zosen Interview Experiences
7 interviews found
only for fun
Selected
I applied via Campus Placement and was interviewed in Feb 2023. There were 3 interview rounds.
(4 Questions)
- Q1. Technical questions about mechanical engineering.
- Q2. Questions about centre of gravity.
- Q3. Basic drawing calculation
- Q4. Thermodynamics questions
(1 Question)
- Q1. Introduce yourself
Selected
I appeared for an interview before Apr 2024, where I was asked the following questions.
- Q1. Related to CNC machine
- Q2. Turning and Deep hole drilling
Interview Preparation Tips
Rushi Bodiwala
I applied via Referral
(1 Question)
- Q1. ASME code. Mostly section viii div 1 basic questions. Question based on past experiences
Interview Preparation Tips
- ASME Codes
- strength of mechanics
2nd round of technical ( face to face interview) : mainly on ASME code. Basis of ASME , deep under standing of ASME. Also knowledge of strength of mechanics are checked ( SMD, BMD).
I applied via Approached by Company and was interviewed before Nov 2021. There were 3 interview rounds.
(4 Questions)
- Q1. Related to Trigonometry which used in pressure vessel fabrication.
- Ans. Trigonometry formula of Sin, Cos, Tan for Area, Volume, etc.
- Q2. How can you implement 5'S in fabrication??
- Ans.
5'S can be implemented in fabrication by organizing and optimizing the workspace.
Sort and remove unnecessary items from the workspace
Set in order the necessary items in a logical and efficient manner
Shine and clean the workspace regularly
Standardize the processes and procedures for maintaining the workspace
Sustain the improvements by continuously monitoring and improving the workspace
Example: Use shadow boards to organ...
- Q3. How to calculate weld deposition?
- Ans.
Weld deposition can be calculated by multiplying the weld bead cross-sectional area by the length of the weld.
Measure the cross-sectional area of the weld bead
Measure the length of the weld
Multiply the cross-sectional area by the length of the weld to get the weld deposition
Weld deposition can be expressed in cubic inches or cubic millimeters
- Q4. How you can calculate SMH?
- Ans.
SMH can be calculated by dividing the total time taken to complete a task by the number of units produced.
SMH stands for Standard Minute Hour
It is used to measure the productivity of a worker or a machine
Formula: SMH = Total time taken to complete a task / Number of units produced
Example: If it takes 120 minutes to produce 100 units, then SMH = 1.2 minutes per unit
(1 Question)
- Q1. Salary Expectations & relocation.
Interview Preparation Tips
- ASME Codes
- Time Study
- SMH
- FABRICATION SEQUENCE
- COST BOOKING
- SAP
Make preparations related to your work.
I applied via LinkedIn and was interviewed in Dec 2021. There was 1 interview round.
Interview Questionnaire
1 Question
- Q1. Material, welding saw & essc, drawing, code asme sec 8
Interview Preparation Tips
Drawing , calculation Eq.like arc length, cord length, and manhours required
Assistant Manager/Manager -(Technical) Interview Questions & Answers
Anonymous
posted on 10 Mar 2021
I applied via Referral and was interviewed in Sep 2020. There were 4 interview rounds.
Interview Questionnaire
4 Questions
- Q1. What is the duty cycle of power contractor?
- Ans.
The duty cycle of a power contractor refers to the amount of time it can operate continuously without overheating or needing to cool down.
The duty cycle is typically expressed as a percentage, representing the ratio of operating time to the total time.
For example, a power contractor with a duty cycle of 50% can operate for 5 minutes and then needs to cool down for 5 minutes before being used again.
A higher duty cycle i...
- Q2. What is the drive and what are the types of drives?
- Ans.
A drive is a device that reads or writes data on a storage medium. Types include hard disk, solid-state, optical, and flash drives.
A drive is a hardware component that allows data to be stored and retrieved from a storage medium.
Hard disk drives use spinning disks to read and write data, while solid-state drives use flash memory.
Optical drives use lasers to read and write data on CDs, DVDs, and Blu-ray discs.
Flash driv...
- Q3. How will you measure efficiency of motor without seeing name plate?
- Ans.
Efficiency of motor can be measured by conducting a load test and measuring the input and output power.
Conduct a load test by connecting the motor to a dynamometer
Measure the input power using a wattmeter
Measure the output power using a torque meter and a speedometer
Calculate the efficiency using the formula: Efficiency = (Output Power/Input Power) x 100%
Compare the calculated efficiency with the standard efficiency fo...
- Q4. How will you identify the type of breakdown (mechanical or electrical) of a solenoid valve?
- Ans.
To identify the type of breakdown in a solenoid valve, one can perform visual inspection, check for electrical continuity, and conduct voltage and resistance tests.
Perform a visual inspection to check for any visible signs of damage or wear on the solenoid valve.
Check for electrical continuity by using a multimeter to test the continuity between the electrical connections of the solenoid valve.
Conduct voltage tests by ...
Interview Preparation Tips
Skills evaluated in this interview
Interview Questionnaire
1 Question
- Q1. Max. Carrier frequency of yaskawa A1000, What is department ISO objective, What MD calculation time.
- Ans.
The max carrier frequency of Yaskawa A1000 is 16kHz. Department ISO objective and MD calculation time are not related to the product.
Max carrier frequency of Yaskawa A1000 is 16kHz
Department ISO objective is not related to the product
MD calculation time is not related to the product
Skills evaluated in this interview
Top trending discussions
Interview questions from similar companies
I applied via Recruitment Consultant and was interviewed before Oct 2019. There were 5 interview rounds.
Interview Questionnaire
4 Questions
- Q1. What is meaning of civil engineering.?
- Ans.
Civil engineering is a branch of engineering that deals with the design, construction, and maintenance of infrastructure.
Civil engineering involves the planning, design, and construction of structures such as buildings, bridges, roads, and dams.
It focuses on ensuring the safety, functionality, and sustainability of infrastructure projects.
Civil engineers use principles of physics, mathematics, and materials science to ...
- Q2. How you given organization profits in your allocated job role.?
- Ans.
I have driven profits through process improvements, cost reductions, and innovative solutions in my engineering roles.
Implemented a new automated testing framework that reduced testing time by 30%, allowing faster product releases and increased revenue.
Led a cross-functional team to redesign a key product feature, resulting in a 15% increase in customer satisfaction and a 10% boost in sales.
Optimized supply chain proce...
- Q3. What are the main quality focus on civil engineering field?
- Ans.
The main quality focus in civil engineering is safety, durability, and sustainability.
Ensuring the safety of structures and infrastructure
Designing for durability and longevity
Incorporating sustainable practices and materials
Adhering to building codes and regulations
Conducting thorough inspections and testing
Using advanced technology and software for design and analysis
Collaborating with other professionals to ensure q...
- Q4. How you doing project efficient?
Interview Preparation Tips
Selected
I applied via Recruitment Consulltant and was interviewed before Apr 2022. There were 4 interview rounds.
C, DS understanding and
C and C++ and domain knowledge
General aptitude test
Software Engineer Interview Questions & Answers
Gilbarco Veeder Root
Anonymous
posted on 18 Feb 2023
Selected
I applied via Campus Placement and was interviewed before Feb 2022. There were 3 interview rounds.
Mathematics, logical reasoning
C/C++, device driver, Networking, objectives
Interview Preparation Tips
Isgec Hitachi Zosen Interview FAQs
Tell us how to improve this page.
Isgec Hitachi Zosen Interviews By Designations
- Isgec Hitachi Zosen Industrial Engineer Interview Questions
- Isgec Hitachi Zosen Assistant Manager/Manager -(Technical) Interview Questions
- Isgec Hitachi Zosen Electrical Engineer Interview Questions
- Isgec Hitachi Zosen Graduate Engineer Trainee (Get) Interview Questions
- Isgec Hitachi Zosen Production Engineer Interview Questions
- Isgec Hitachi Zosen Senior Production Engineer Interview Questions
- Isgec Hitachi Zosen Senior Design Engineer Interview Questions
Interview Questions for Popular Designations
Overall Interview Experience Rating
based on 5 interview experiences
Difficulty level
Duration
Interview Questions from Similar Companies
Isgec Hitachi Zosen Reviews and Ratings
based on 108 reviews
Rating in categories
|
Production Engineer
16
salaries
|  ₹5.2 L/yr - ₹8 L/yr |
|
Assistant Manager
14
salaries
| ₹9.7 L/yr - ₹16.5 L/yr |
|
Senior Engineer
14
salaries
| ₹6.8 L/yr - ₹12 L/yr |
|
Deputy Manager
11
salaries
| ₹14 L/yr - ₹17 L/yr |
|
Engineer
8
salaries
| ₹3.6 L/yr - ₹8.3 L/yr |
Gilbarco Veeder Root
HYT Engineering
Kirloskar Toyota Textile Machinery
Hyundai Construction Equipment
- Home >
- Interviews >
- Isgec Hitachi Zosen Interview Questions
