Add office photos
i
HI-FAB Engineers
Compare
Filter interviews by
HI-FAB Engineers Interview Questions, Process, and Tips
Top HI-FAB Engineers Interview Questions and Answers
- Q1. What is first angle and third angle projection?asked in Mechanical Engg. Design interview
- Q2. How to mechanical seal installation, asembly, disassembly,asked in Mechanical Engineer interview
HI-FAB Engineers Interview Experiences
4 interviews found
I applied via Naukri.com and was interviewed in May 2022. There were 2 interview rounds.
(2 Questions)
- Q1. What is first angle and third angle projection?
- Ans.
First angle and third angle projection are two methods used in engineering drawing to represent a 3D object on a 2D plane.
First angle projection is commonly used in Europe and Asia, while third angle projection is commonly used in North America.
In first angle projection, the object is placed in the first quadrant and the views are projected onto the planes behind the object.
In third angle projection, the object is plac...
- Q2. Whats is fits? And its application
- Ans.
Fits refer to the range of tightness or looseness between two mating parts. It is used to ensure proper functioning and assembly of mechanical components.
Fits are used to determine the amount of clearance or interference between two mating parts.
They are classified into three types: clearance fit, interference fit, and transition fit.
Clearance fit allows for free movement between the parts, interference fit creates a p...
(3 Questions)
- Q1. What is gd&t? And different symbols?
- Ans.
GD&T stands for Geometric Dimensioning and Tolerancing. It is a system of symbols and rules used to specify the geometry of mechanical parts.
GD&T is used to communicate design intent and ensure parts are manufactured to the correct specifications.
Some common symbols used in GD&T include concentricity, perpendicularity, and flatness.
GD&T can also be used to specify tolerances for features such as size, position, and ori...
- Q2. What is shaft basis and hole basis system?
- Ans.
Shaft basis and hole basis are two systems used to determine the tolerance limits of mating parts in mechanical design.
Shaft basis system: The shaft is kept constant and the hole is varied to achieve the desired fit.
Hole basis system: The hole is kept constant and the shaft is varied to achieve the desired fit.
The system chosen depends on the application and the desired level of clearance or interference between the ma...
- Q3. What is k factor in sheet metal?
- Ans.
K factor is a ratio that represents the location of the neutral axis in relation to the thickness of the sheet metal.
K factor is used in sheet metal bending to determine the amount of bending force required.
It is a ratio of the distance from the neutral axis to the inside bend radius over the material thickness.
Different materials and bending processes have different k factors.
K factor affects the accuracy of the flat ...
Interview Preparation Tips
Skills evaluated in this interview
Mechanical Engg. Design Interview Questions asked at other Companies
I applied via Recruitment Consulltant and was interviewed in Nov 2021. There were 2 interview rounds.
(1 Question)
- Q1. How many experiences you have ? Which machine you operate ? And which controller knowledge you have ?
(1 Question)
- Q1. All details about drawing reading and how many operation yo know etc que
Interview Preparation Tips
I applied via Walk-in and was interviewed in Feb 2021. There was 1 interview round.
Interview Questionnaire
5 Questions
- Q1. Regarding Rotating Equipment
- Q2. Such as equipment parameters
- Q3. Equipment installation commissioning, trobleasot
- Q4. How to mechanical seal installation, asembly, disassembly,
- Ans.
Mechanical seal installation, assembly, and disassembly require proper tools and techniques to ensure a leak-free operation.
Choose the right type of mechanical seal for the application
Clean and inspect all components before installation
Use a proper lubricant to prevent damage during assembly
Tighten bolts in a criss-cross pattern to ensure even pressure
Follow manufacturer's instructions for disassembly and reassembly
Ins...
- Q5. Failures inspection of all rotating / statics equipment
- Ans.
Inspection of rotating/static equipment failures
Perform regular inspections to identify potential failures
Use non-destructive testing methods to detect cracks or defects
Check for proper lubrication and alignment
Monitor vibration levels to detect abnormalities
Inspect electrical components for signs of wear or damage
Keep detailed records of inspections and maintenance
Address any identified issues promptly to prevent furt
Interview Preparation Tips
Mechanical Engineer Interview Questions asked at other Companies
Interview Questionnaire
3 Questions
- Q1. Engineering drawing red?
- Q2. Experience ?
- Q3. Why are you left your job ?
CNC Operator Interview Questions asked at other Companies
HI-FAB Engineers interview questions for popular designations
Interview questions from similar companies
I was interviewed in Nov 2024.
(4 Questions)
- Q1. Wind calculation as per IS code
- Ans.
The procedure for wind calculation as per IS code involves determining the design wind speed, selecting the appropriate terrain category, and calculating the wind pressure.
Determine the design wind speed based on the location and height of the structure.
Select the appropriate terrain category (rural, urban, etc.) as per IS code guidelines.
Calculate the wind pressure using the formula provided in the IS code.
Consider fa...
- Q2. SFD and BMD of cantilever beam
- Q3. Staad model for fixed pole
- Ans.
A STAAD model for a fixed pole is a structural analysis and design model used to determine the stability and strength of a pole that is fixed in place.
In a STAAD model for a fixed pole, the pole is typically modeled as a vertical member with fixed supports at the base.
The model considers factors such as wind loads, dead loads, and any other relevant loads that may act on the pole.
The analysis helps in determining the s...
- Q4. Design of Square base plate
- Ans.
Key considerations in designing a square base plate
Ensure the base plate is large enough to support the load without excessive deflection
Select appropriate material and thickness to meet structural requirements
Consider the connection details for attaching the base plate to the structure
Account for any potential corrosion or environmental factors that may affect the base plate
Include provisions for anchor bolts or other...
Interview Preparation Tips
Junior Engineer - mould Maintenance Interview Questions & Answers
Tokai Rubber Auto Parts India
Anonymous
posted on 28 Jul 2022
Selected
I applied via Recruitment Consulltant and was interviewed before Jul 2021. There was 1 interview round.
(3 Questions)
- Q1. Group discussion
- Q2. Hr round and discussion
- Q3. Technical round and injection moulding related any questions
Interview Preparation Tips
- Injection Moulding
Selected
I applied via Walk-in and was interviewed in Oct 2024. There was 1 interview round.
(2 Questions)
- Q1. Tell me about your self
- Q2. What is difference between diesel engine and petrol engine
- Ans.
Diesel engines use compression ignition while petrol engines use spark ignition.
Diesel engines use compression ignition, where the fuel-air mixture is compressed until it spontaneously ignites.
Petrol engines use spark ignition, where a spark plug ignites the fuel-air mixture.
Diesel engines are more fuel efficient than petrol engines.
Petrol engines generally have higher power output compared to diesel engines.
Diesel eng...
Interview Preparation Tips
Selected
I applied via LinkedIn and was interviewed in Jul 2024. There was 1 interview round.
(3 Questions)
- Q1. Tell me about yourself
- Ans.
I am a highly motivated and results-driven individual with a strong background in sales and business development.
Experienced in developing and implementing sales strategies
Proven track record of exceeding sales targets
Strong communication and negotiation skills
Ability to build and maintain relationships with clients
Passionate about driving business growth and achieving success
- Q2. Have you done sales, how to do cold call
- Ans.
Yes, I have experience in sales and cold calling.
Research the prospect before calling to understand their needs
Prepare a script or talking points to guide the conversation
Be confident and polite during the call
Listen actively to the prospect's responses and adjust your approach accordingly
Follow up with an email or additional information after the call
- Q3. What you know about company
- Ans.
Company is a leading provider of software solutions for businesses in the BDM industry.
Company offers a wide range of software products tailored for BDM professionals.
They have a strong reputation for delivering innovative and user-friendly solutions.
Company has a dedicated customer support team to assist clients with any issues or questions.
Their software helps businesses streamline their BDM processes and improve eff...
(3 Questions)
- Q1. Manufacturing department
- Q2. Manpower handle
- Q3. Daily target production
Interview Preparation Tips
(1 Question)
- Q1. How does a CNC machine works?
- Ans.
A CNC machine works by using computer programs to control the movement of the machine's tools and workpiece to create precision parts.
CNC machines use computer programs to control the movement of the cutting tools and workpiece.
The programs are created using CAD/CAM software and converted into G-code instructions.
The machine reads the G-code instructions and moves the tools along the specified paths to cut and shape th...
HI-FAB Engineers Interview FAQs
Tell us how to improve this page.
Interview Questions for Popular Designations
- Analyst Interview Questions
- Software Engineer Interview Questions
- Senior Engineer Interview Questions
- Sales Executive Interview Questions
- Graduate Engineer Trainee (Get) Interview Questions
- Java Developer Interview Questions
- Test Engineer Interview Questions
- Senior Software Engineer Interview Questions
- Show more
People are getting interviews through
Interview Questions from Similar Companies
HI-FAB Engineers Reviews and Ratings
based on 38 reviews
Rating in categories
|
Design Engineer
9
salaries
|  ₹3.8 L/yr - ₹5 L/yr |
|
Engineer- Customer Support
8
salaries
| ₹2.4 L/yr - ₹4.5 L/yr |
|
Production Engineer
8
salaries
| ₹3 L/yr - ₹4.5 L/yr |
|
Service Engineer
6
salaries
| ₹3.2 L/yr - ₹5.5 L/yr |
|
CNC Programmer cum Setter
5
salaries
| ₹2.1 L/yr - ₹4 L/yr |
L&T Construction
Tata Projects
Thermax Limited
Kirloskar Brothers
Calculate your in-hand salary
- Home >
- Interviews >
- HI-FAB Engineers Interview Questions
