Echaar Equipments Planning Engineer Interview Questions and Answers

Q1. What is free float & total float?
Ans. 
Free float is the amount of time a task can be delayed without affecting the project's critical path. Total float is the total amount of time a task can be delayed without delaying the project's completion.
• Free float is specific to an individual task, while total float is applicable to the entire project.

• Free float is calculated by subtracting the early start date of a task from the early finish date of its successor t...read more
Answered by AI
Add your answer
Q2. What is critival path?
Ans. 
Critical path is the longest sequence of activities in a project that determines the project's overall duration.
• Critical path consists of activities that have zero slack or float time.

• Any delay in activities on the critical path will directly impact the project's completion time.

• Activities on the critical path must be closely monitored and managed to ensure timely project completion.

• Critical path analysis helps in iden...read more
Answered by AI
Add your answer
Q3. What is look ahead and how find 1month look ahead in P6?
Ans. 
Look ahead is a planning technique to anticipate future activities. In P6, the 1-month look ahead can be found using filters and layouts.
• Look ahead is a proactive planning approach to identify and prepare for upcoming activities.

• In P6, the 1-month look ahead can be created by applying filters and layouts to the project schedule.

• Filters can be set to display activities that are scheduled within the next month.

• Layouts ca...read more
Answered by AI
Add your answer
Q4. What is global change?
Ans. 
Global change refers to the long-term alterations in the Earth's systems and processes due to human activities and natural factors.
• Global change encompasses various interconnected phenomena such as climate change, biodiversity loss, deforestation, and pollution.

• It involves both anthropogenic (human-induced) factors like greenhouse gas emissions and natural factors like volcanic eruptions.

• Global change has wide-ranging ...read more
Answered by AI
Add your answer
Q5. Productivity rate of a welder ?
Ans. 
The productivity rate of a welder refers to the amount of work they can complete in a given time period.
• Productivity rate is measured in units of work per hour or per day.

• Factors that can affect a welder's productivity rate include their skill level, the complexity of the welding task, and the availability of necessary equipment.

• For example, an experienced welder may have a higher productivity rate than a novice welder...read more
Answered by AI
Add your answer

Asked to prepare a schedule of a building

Q1. Project Planning Process
Ans. 
Project planning process involves defining project scope, creating a schedule, allocating resources, and monitoring progress.
• Define project scope and objectives

• Create a project schedule with milestones and deadlines

• Allocate resources such as budget, manpower, and materials

• Monitor progress and make adjustments as needed

• Communicate with stakeholders regularly
Answered by AI
Add your answer

Q1. Job Profile based questions
Add your answer

Q1. About overall career, family & Salary discussion.
Add your answer

As on production planning control

Q1. Boom check in company
Add your answer
Q2. How to save the company wastege
Ans. 
Implementing lean manufacturing principles, optimizing production processes, and reducing material waste can help save company wastage.
• Implement lean manufacturing principles to reduce waste in production processes

• Optimize production schedules to minimize downtime and maximize efficiency

• Reduce material waste by implementing recycling and reusing strategies

• Regularly review and analyze production data to identify areas o...read more
Answered by AI
Add your answer

Q1. Code of fabrication and Installation, Fabrication Sequence with final dispatch erection site
Ans. 
The code of fabrication and installation involves a sequence of steps from fabrication to dispatch and erection at the site.
• The code of fabrication and installation outlines the standards and procedures for the entire process.

• The fabrication sequence involves cutting, welding, and assembling the components according to the design specifications.

• The final dispatch involves packaging and transportation of the fabricated ...read more
Answered by AI
Add your answer
Q2. First introduced, Self respect, job site bahavior workmanship with staff like technical
Add your answer

Q1. Diploma Regarding
Add your answer
Q2. Electrical information
Add your answer
Q3. What is the transformer. Transformer Working.
Ans. 
A transformer is an electrical device that transfers electrical energy between two or more circuits through electromagnetic induction.
• Transformers work on the principle of electromagnetic induction

• They consist of two coils of wire, known as the primary and secondary windings

• The primary winding is connected to the input voltage source, while the secondary winding is connected to the output load

• The transformer changes th...read more
Answered by AI
Add your answer
Q4. What is resistor. What is the measure resistor without multimeter.
Ans. 
A resistor is an electronic component that resists the flow of electrical current.
• Resistors are used to control the amount of current flowing in a circuit.

• The resistance of a resistor is measured in ohms (Ω).

• One way to measure a resistor without a multimeter is by using a simple circuit with a known voltage source and an ammeter to measure the current flowing through the resistor.

• Another method is to use a resistor col...read more
Answered by AI
Add your answer

Q1. What is free float & total float?
Ans. 
Free float is the amount of time a task can be delayed without affecting the project's critical path. Total float is the total amount of time a task can be delayed without delaying the project's completion.
• Free float is specific to an individual task, while total float is applicable to the entire project.

• Free float is calculated by subtracting the early start date of a task from the early finish date of its successor t...read more
Answered by AI
Add your answer
Q2. What is critival path?
Ans. 
Critical path is the longest sequence of activities in a project that determines the project's overall duration.
• Critical path consists of activities that have zero slack or float time.

• Any delay in activities on the critical path will directly impact the project's completion time.

• Activities on the critical path must be closely monitored and managed to ensure timely project completion.

• Critical path analysis helps in iden...read more
Answered by AI
Add your answer
Q3. What is look ahead and how find 1month look ahead in P6?
Ans. 
Look ahead is a planning technique to anticipate future activities. In P6, the 1-month look ahead can be found using filters and layouts.
• Look ahead is a proactive planning approach to identify and prepare for upcoming activities.

• In P6, the 1-month look ahead can be created by applying filters and layouts to the project schedule.

• Filters can be set to display activities that are scheduled within the next month.

• Layouts ca...read more
Answered by AI
Add your answer
Q4. What is global change?
Ans. 
Global change refers to the long-term alterations in the Earth's systems and processes due to human activities and natural factors.
• Global change encompasses various interconnected phenomena such as climate change, biodiversity loss, deforestation, and pollution.

• It involves both anthropogenic (human-induced) factors like greenhouse gas emissions and natural factors like volcanic eruptions.

• Global change has wide-ranging ...read more
Answered by AI
Add your answer
Q5. Productivity rate of a welder ?
Ans. 
The productivity rate of a welder refers to the amount of work they can complete in a given time period.
• Productivity rate is measured in units of work per hour or per day.

• Factors that can affect a welder's productivity rate include their skill level, the complexity of the welding task, and the availability of necessary equipment.

• For example, an experienced welder may have a higher productivity rate than a novice welder...read more
Answered by AI
Add your answer

Asked to prepare a schedule of a building

Q1. What is your qualifications.
Ans. 
I have a Bachelor's degree in Civil Engineering and a Master's degree in Construction Management.
• Bachelor's degree in Civil Engineering

• Master's degree in Construction Management

• Experience in planning and scheduling

• Proficient in using planning software such as Primavera P6

• Strong analytical and problem-solving skills
Answered by AI
View 1 more answer
Q2. How many years of your experience and in which company?
Ans. 
I have 5 years of experience in planning and billing engineering.
• I worked for XYZ Company for 3 years as a Planning Engineer.

• Then I joined ABC Company as a Billing Engineer and worked there for 2 years.

• During my tenure, I gained expertise in project planning, cost estimation, and budgeting.

• I also have experience in using various software tools like Primavera, MS Project, and SAP.

• I have successfully completed several pr
Answered by AI
Add your answer
Q3. Deploma in civil Engineer B Teach in Civil Engineering
Add your answer
Q4. 7.5 Year Experience
Ans. 
I have 7.5 years of experience in Planning & Billing Engineering.
• During my 7.5 years of experience, I have gained expertise in project planning, scheduling, and cost estimation.

• I have worked on various projects, including construction, infrastructure, and industrial projects.

• I have experience in using software such as Primavera P6, MS Project, and Excel for project planning and scheduling.

• I have also worked on project ...read more
Answered by AI
Add your answer