Cummins CMM Programmer Interview Questions and Answers

Q1. What is synchronous and histerisis motor
Ans. 
Synchronous motor runs at a constant speed while hysteresis motor has a rotor that follows the rotating magnetic field.
• Synchronous motor is used in applications where constant speed is required, such as in clocks and timers.

• Hysteresis motor is used in applications where precise control of speed is required, such as in record players and tape recorders.

• Synchronous motor has a stator and rotor that rotate at the same spe...read more
Answered by AI
Add your answer
Q2. Different between plc and scada
Ans. 
PLC is a hardware device that controls industrial processes, while SCADA is a software system that monitors and controls those processes.
• PLC is a programmable logic controller that controls the input/output of industrial processes.

• SCADA is a supervisory control and data acquisition system that collects and analyzes data from the industrial processes.

• PLC is a hardware device, while SCADA is a software system.

• PLC is used...read more
Answered by AI
Add your answer
Q3. Different between relay and contactor
Ans. 
Relays are used for low power applications while contactors are used for high power applications.
• Relays are typically used in control circuits to switch low power loads such as lights and fans.

• Contactors are used to switch high power loads such as motors and compressors.

• Relays have a lower current rating than contactors.

• Contactors have larger contacts and can handle higher currents than relays.

• Relays are typically smal...read more
Answered by AI
Add your answer
Q4. Different between switch and relay
Ans. 
Switches are used to control the flow of current in a circuit, while relays are used to switch a circuit on or off.
• Switches are manually operated, while relays are electrically operated.

• Switches are used in low voltage applications, while relays are used in high voltage applications.

• Switches are simple in construction, while relays are more complex.

• Examples of switches include light switches and toggle switches, while ...read more
Answered by AI
Add your answer

Q1. Different between switch and timer
Ans. 
Switch is an electronic component used to connect or disconnect a circuit while a timer is a device used to measure time intervals.
• Switch is used to turn on/off a device while timer is used to control the duration of a device's operation.

• Switch is a binary device with two states (on/off) while timer can be analog or digital and can measure time in seconds, minutes, or hours.

• Examples of switches include light switches, ...read more
Answered by AI
Add your answer

Q1. What is difference between RTD and thermocouple used
Ans. 
RTD measures temperature using resistance change, while thermocouple uses voltage change.
• RTD stands for Resistance Temperature Detector, while thermocouple generates voltage based on temperature difference.

• RTDs are more accurate and stable compared to thermocouples.

• RTDs have higher initial cost but lower long-term maintenance cost.

• Thermocouples are more rugged and can withstand higher temperatures than RTDs.

• Example: RT...read more
Answered by AI
Add your answer
Q2. What is the PLC and DCS system
Ans. 
PLC and DCS systems are control systems used in industrial automation to monitor and control processes.
• PLC stands for Programmable Logic Controller, used for controlling machinery and processes in manufacturing.

• DCS stands for Distributed Control System, used for controlling complex processes across multiple locations.

• PLCs are typically used for discrete control applications, while DCS systems are used for continuous co...read more
Answered by AI
Add your answer
Q3. What is the AC And DC drive
Ans. 
AC and DC drives are types of electrical drives used to control the speed and torque of electric motors.
• AC drive controls the speed of an AC motor by varying the frequency of the electrical supply.

• DC drive controls the speed of a DC motor by varying the voltage supplied to the motor.

• AC drives are more commonly used in industrial applications due to their efficiency and flexibility.

• DC drives are often used in applicatio...read more
Answered by AI
Add your answer
Q4. What do you understand by 4 wire and 2 wire
Ans. 
4 wire and 2 wire are configurations used in electrical circuits for measuring resistance.
• 4 wire configuration is used for accurate resistance measurements by eliminating lead resistance

• 2 wire configuration is simpler but less accurate due to lead resistance affecting measurements

• Examples: 4 wire used in precision instruments like multimeters, 2 wire used in basic circuit testing
Answered by AI
Add your answer

Electrical related questions

Q1. Technical questions
Add your answer
Q2. Related to job for junior engineer
Ans. 
I have raedy to job for office or work from Home
Answered by Pallavi Patil
Add your answer
Q3. Job time is part time
Add your answer
Q4. Salary of a month
Add your answer
Q5. Which post to join to company
Add your answer
Q6. All doubts to ask
Add your answer
Q7. I ask to my question to join company process is very fast
Ans. 
I mean reply me to HR for job
Answered by Pallavi Patil
Add your answer

Q1. Which is a product manufacturers this company
Add your answer
Q2. Something ask for junior engineer job
Add your answer
Q3. Discussion with company for job
Add your answer
Q4. Discussion with staff members
Add your answer

Related to electrical engineering bases

Q1. Last job salary and experience details.
Add your answer

Q1. Job related technical questions like rolling mill, especially drives.
Add your answer

Q1. Salary negotiation.
Add your answer

Q1. Technically about company like safety..
Add your answer
Q2. What is 5s and devine
Ans. 
5S is a methodology used to organize and maintain a clean and efficient workplace.
• 5S stands for Sort, Set in Order, Shine, Standardize, and Sustain.

• It involves organizing and labeling tools and materials, cleaning and maintaining equipment, and creating a culture of continuous improvement.

• Example: A factory implementing 5S might label all tools and materials, create a designated storage area for each item, and regularl...read more
Answered by AI
Add your answer

Q1. Self introduction
Ans. I am govindasamy from dharmapuri working maintenance engineer 8years experience
Answered Anonymously
Add your answer
Q2. Telmi your aditional skills
Ans. Plc analysis then all rounder and auditing facilities my improve
Answered Anonymously
Add your answer
Q3. Why resigning last company
Add your answer
Q4. Which type of work your femilear
Ans. 
I am familiar with various types of engineering work, including mechanical, electrical, and civil engineering.
• Mechanical engineering - designing and analyzing mechanical systems

• Electrical engineering - working with electrical circuits and systems

• Civil engineering - designing and constructing infrastructure projects

• Project management - overseeing and coordinating engineering projects
Answered by AI
Add your answer
Q5. Why choose those company
Add your answer