Bridge & Roof Co Graduate Engineer Trainee (Get) Interview Questions and Answers

135/150 there were 75 questions of 2 marks of basic aptitude but time is also 1 hour

Q1. They ask me about my civil engineering basics and my critical thinking Tell me about your self
Add your answer
Q2. How stress is related to strain
Ans. 
Stress and strain are related as stress is the force applied per unit area, while strain is the deformation caused by stress.
• Stress is the force applied per unit area, while strain is the deformation caused by stress.

• Stress is measured in units of force per unit area, such as pounds per square inch (psi) or pascals (Pa).

• Strain is measured as the change in length or shape of a material due to stress, and is typically ex...read more
Answered by AI
Add your answer

Q1. 1.What are pumps 2.What are flow meters. How their working vary? On increasing the value of Reflux ratio in distillation column what happens? What are the modes of heat transfer?
Ans. 
Questions related to pumps, flow meters, distillation column, and heat transfer modes.
• Pumps are devices used to move fluids by mechanical action.

• Flow meters are instruments used to measure the flow rate of fluids.

• The working of flow meters varies depending on the type of flow meter used.

• Increasing the reflux ratio in a distillation column increases the purity of the distillate.

• The modes of heat transfer are conduction,
Answered by AI
View 1 more answer
Q2. What is distillation?
Ans. 
Distillation is a process of separating components of a mixture based on their boiling points.
• It involves heating the mixture to vaporize the component with the lowest boiling point.

• The vapor is then condensed and collected as a separate liquid.

• This process can be used to purify liquids, separate different components of a mixture, and extract essential oils from plants.

• Examples include the distillation of crude oil to ...read more
Answered by AI
Add your answer
Q3. What are various types of flow meters
Ans. 
Flow meters are devices used to measure the flow rate or quantity of a gas or liquid moving through a pipe.
• Differential pressure flow meters

• Positive displacement flow meters

• Velocity flow meters

• Mass flow meters

• Open channel flow meters
Answered by AI
Add your answer
Q4. Working of flow meters
Ans. 
Flow meters measure the rate of fluid flow in a pipe or channel.
• Flow meters work by measuring the velocity of the fluid and the cross-sectional area of the pipe or channel.

• There are different types of flow meters such as differential pressure flow meters, positive displacement flow meters, and electromagnetic flow meters.

• Flow meters are used in various industries such as oil and gas, water treatment, and food and bever...read more
Answered by AI
Add your answer
Q5. What is heat exchanger and it's working?
Ans. 
A heat exchanger is a device used to transfer heat between two or more fluids.
• Heat exchangers are used in various industries such as chemical, power, and HVAC.

• They work by allowing two fluids to flow through separate channels, with heat transferring from one fluid to the other.

• Common types of heat exchangers include shell and tube, plate and frame, and finned tube.

• Heat exchangers can be used for heating, cooling, or bo...read more
Answered by AI
Add your answer

Q1. Draw BMD & SFD of a Simply Supported Beam shown to my screen. Draw it & show that on screen.
Ans. 
The candidate is asked to draw the BMD & SFD of a Simply Supported Beam shown on the screen.
• Identify the support conditions of the beam (simply supported in this case)

• Determine the loads acting on the beam and their positions

• Calculate the reactions at the supports

• Draw the Bending Moment Diagram (BMD) and Shear Force Diagram (SFD) based on the calculated values

• Label the diagrams with appropriate values and units
Answered by AI
Add your answer
Q2. What are the values of Compressive & Tensile Shear Stress on a Singly Reinforced Beam in LSM method?
Ans. 
Compressive shear stress is zero while tensile shear stress is equal to the shear force divided by the cross-sectional area of the beam.
• Compressive shear stress is zero in a singly reinforced beam according to the Limit State Method (LSM).

• Tensile shear stress is calculated by dividing the shear force by the cross-sectional area of the beam.

• For example, if the shear force acting on the beam is 10 kN and the cross-sectio...read more
Answered by AI
Add your answer
Q3. Some other civil engineering questions.
Add your answer
Q4. Introduce Yourself. This is 1st Question.
Add your answer

Very Easy general aptitude questions are asked in a MCQ pattern

Q1. Should we continue concreting of foundation the next day, if there is one day of continuous rainfall?
Ans. 
No, it is not advisable to continue concreting of foundation the next day after one day of continuous rainfall.
• Continuous rainfall can saturate the soil, making it unstable for concreting.

• Rainwater can mix with the concrete, affecting its strength and durability.

• The presence of water can lead to the formation of voids and cracks in the foundation.

• It is important to ensure that the foundation is dry and stable before pr...read more
Answered by AI
View 1 more answer

Q1. Are you open to work over pan India?
Add your answer

30 minutes, Aptitude and Technical

Q1. Where do you see yourself in 5 years?
Add your answer
Q2. What are your strengths and weaknesses?
Add your answer
Q3. Tell me about yourself.
Add your answer