i
Advik Hi Tech
Filter interviews by
Clear (1)
Accounting questions were asked. Easy. Same with interview
Top trending discussions
I applied via Referral and was interviewed before Sep 2021. There were 2 interview rounds.
I applied via Approached by Company and was interviewed before Dec 2021. There were 3 interview rounds.
First off all, we ought to have some sortoff automobile and production knowledge because they will definitely check our technical skill secondly, listening skill and fluency plays significant factor
TQBM stands for 'Tudo Que Bem' which means 'Everything is fine' in Portuguese. BOM means 'good' in Portuguese.
TQBM is a common phrase used in Brazil to ask if everything is okay.
BOM is often used as a response to TQBM to indicate that everything is good.
Both TQBM and BOM are informal and commonly used in everyday conversations.
Example: A friend asks 'TQBM?' and you respond 'BOM, e voce?' which means 'Everything is fine
I applied via Referral and was interviewed before Feb 2021. There was 1 interview round.
Line balancing is the process of optimizing workstations in a production line to minimize idle time and maximize efficiency.
It involves analyzing the production process and identifying bottlenecks
Tasks are then rearranged to balance the workload across workstations
The goal is to achieve a smooth and continuous flow of work
Example: In a car assembly line, line balancing would involve ensuring that each workstation has a...
I applied via Indeed and was interviewed before Feb 2020. There were 3 interview rounds.
I applied via Recruitment Consulltant and was interviewed before Oct 2022. There were 3 interview rounds.
A relay holding circuit diagram is used to keep the relay in the energized state even after the control signal is removed.
The circuit typically includes a holding contact that maintains the relay coil energized.
A latching relay can also be used for holding without continuous power supply.
Examples: ladder logic diagram with a holding contact, latching relay circuit diagram.
PNP and NPN are types of bipolar junction transistors commonly used in electronic circuits.
PNP transistor has a layer of N-type semiconductor between two layers of P-type semiconductor, while NPN transistor has a layer of P-type semiconductor between two layers of N-type semiconductor.
In a PNP transistor, current flows from the emitter to the base and then to the collector, while in an NPN transistor, current flows fro...
There are various types of sensors used for different purposes.
Temperature sensors (e.g. thermocouples, thermistors)
Pressure sensors (e.g. piezoelectric sensors)
Motion sensors (e.g. accelerometers, gyroscopes)
Proximity sensors (e.g. ultrasonic sensors)
Light sensors (e.g. photodiodes, phototransistors)
PLC stands for Programmable Logic Controller, which is a digital computer used for automation of electromechanical processes.
PLC is used to control machinery in manufacturing processes, such as assembly lines, robotic devices, or any activity that requires high reliability control.
It is programmed using a specialized computer language, typically ladder logic or function block diagram.
PLCs are commonly used in industrie...
I applied via Referral and was interviewed in Jul 2021. There was 1 interview round.
I applied via Company Website
TTR stands for Total Thickness Range and is required for powder coating process to ensure proper adhesion and durability.
TTR is the range of thickness of the substrate and any coatings applied to it
It is important for powder coating as it ensures proper adhesion and durability
If the TTR is too large, the coating may not adhere properly or may crack and peel over time
Examples of substrates with varying TTR include alumi
Detection and prevention poka-yoke refers to the use of techniques to identify and prevent errors in a process.
Poka-yoke is a Japanese term for mistake-proofing
Detection poka-yoke involves identifying errors as they occur
Prevention poka-yoke involves designing processes to prevent errors from occurring
Examples of poka-yoke include using checklists, color-coding, and physical barriers
Poka-yoke can improve quality, reduc
Decrease in pH can occur due to various factors in conversion coating.
Decrease in pH can be caused by the addition of an acid or acidic solution.
Presence of reactive metals in the coating can lead to a decrease in pH.
Contamination by organic materials or impurities can also lower the pH.
Chemical reactions during the conversion coating process may result in pH decrease.
Examples of conversion coatings include phosphating
To prepare 0.1 N H2SO4 & NaOH, calculate the required amount of solute and dissolve it in distilled water.
Calculate the molar mass of H2SO4 and NaOH
Determine the required amount of solute using the formula: N = (W/M) x (1000/V)
Dissolve the calculated amount of solute in distilled water to make 1 liter of solution
Standardize the solution using a primary standard
Use a burette to measure the volume of solution needed for
To cross verify 0.1 normality H2SO4, use a standard solution of NaOH and an indicator.
Prepare a standard solution of NaOH of known concentration.
Add a few drops of an indicator such as phenolphthalein to the H2SO4 solution.
Titrate the H2SO4 solution with the NaOH solution until the endpoint is reached.
The endpoint is when the indicator changes color, indicating that all the H2SO4 has reacted with the NaOH.
Calculate the...
Prepare a pH buffer solution as per defined standard in tablet.
Determine the required pH value and buffer capacity
Select the appropriate buffer system and calculate the required amounts of buffer components
Dissolve the buffer components in water and adjust the pH as necessary
Check the pH and adjust if necessary
Filter the solution and store in a clean container
Use a calibrated pH meter to verify the pH of the solution
Plastics are made through a process called polymerization, where monomers are chemically bonded together to form long chains.
Plastics are made from polymers, which are large molecules made up of repeating units called monomers.
The most common method of making plastics is through polymerization, where monomers are chemically bonded together to form long chains.
Different types of plastics are made using different monomer...
Injection molding is a manufacturing process used to produce parts by injecting material into a mold.
Material is heated and injected into a mold cavity
The material cools and solidifies to form the desired shape
Commonly used for producing plastic parts in mass production
Examples include plastic bottles, automotive parts, and medical devices
I applied via Referral and was interviewed before Sep 2023. There were 2 interview rounds.
Question related to NPD
Casting is the process of pouring molten metal into a mold to create a specific shape.
Casting involves creating a mold, melting the metal, pouring the metal into the mold, and allowing it to cool and solidify.
Different types of casting methods include sand casting, investment casting, die casting, and continuous casting.
Casting is used in various industries such as automotive, aerospace, and jewelry making.
based on 1 interview
Interview experience
Senior Engineer
219
salaries
| ₹0 L/yr - ₹0 L/yr |
Quality Engineer
137
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
120
salaries
| ₹0 L/yr - ₹0 L/yr |
Production Engineer
90
salaries
| ₹0 L/yr - ₹0 L/yr |
Engineer
85
salaries
| ₹0 L/yr - ₹0 L/yr |
Bosch
UNO Minda
Bharat Forge
Mahindra & Mahindra