Upload Button Icon Add office photos

Tecnimont

Compare button icon Compare button icon Compare

Filter interviews by

Tecnimont Revit Designer Interview Questions, Process, and Tips

Updated 8 Dec 2021

Top Tecnimont Revit Designer Interview Questions and Answers

Tecnimont Revit Designer Interview Experiences

2 interviews found

Interview Questionnaire 

4 Questions

  • Q1. Self introduction
  • Q2. What is lap length?
  • Ans. 

    Lap length is the amount of overlap between two reinforcing bars in a concrete structure.

    • Lap length is important for ensuring the strength and stability of a concrete structure.

    • It is typically specified in building codes and engineering standards.

    • The lap length required depends on the diameter of the reinforcing bars and the strength of the concrete.

    • For example, in a reinforced concrete beam, the lap length might be 40...

  • Answered by AI
  • Q3. What is developement length?
  • Ans. 

    Development length is the minimum length of reinforcement required to transfer the stress from steel to concrete.

    • It is the length of the bar required to be embedded in the concrete to transfer the load.

    • It depends on the diameter of the bar, the grade of steel, and the strength of concrete.

    • It is calculated using the formula provided in the codebook.

    • It is important to ensure proper development length to prevent failure o

  • Answered by AI
  • Q4. What is BBS? & explain it.
  • Ans. 

    BBS stands for Bar Bending Schedule. It is a document that provides details of reinforcement steel required for construction.

    • BBS is used in construction to ensure the correct amount of reinforcement steel is used.

    • It includes details such as the diameter, length, and number of steel bars required.

    • BBS is created based on the structural drawings and specifications.

    • It helps in estimating the cost of reinforcement steel and...

  • Answered by AI

Interview Questionnaire 

4 Questions

  • Q1. Self introduction
  • Q2. What is lap langth??
  • Ans. 

    Lap length is the amount of overlap between two reinforcing bars in a concrete structure.

    • It is important for ensuring the strength and stability of the structure.

    • The lap length is determined by the diameter of the bars and the strength of the concrete.

    • For example, in a beam, the lap length is typically 50 times the diameter of the bar.

    • Lap length requirements may vary depending on the specific building codes and regulat

  • Answered by AI
  • Q3. What is development length?
  • Ans. 

    Development length is the minimum length of reinforcement required to transfer the stress from reinforcing bar to concrete.

    • It is the length of the bar that must be embedded in concrete to develop its full strength.

    • It is influenced by the diameter of the bar, the strength of the concrete, and the bond strength between the bar and the concrete.

    • It is calculated using the formula Ld = (phi x Fy x As) / (4 x tau x sqrt(f'c)...

  • Answered by AI
  • Q4. What is BBS? & Explain it.
  • Ans. 

    BBS stands for Bar Bending Schedule. It is a document that provides details of reinforcement steel required for construction.

    • BBS is used in construction to ensure the correct amount of reinforcement steel is used.

    • It includes details such as the diameter and length of each steel bar.

    • BBS helps to minimize wastage of steel and ensures the structural integrity of the building.

    • It is an important document for contractors, en...

  • Answered by AI

Revit Designer Interview Questions Asked at Other Companies

asked in Tecnimont
Q1. What is BBS? & explain it.
asked in Tecnimont
Q2. What is developement length?
asked in Tecnimont
Q3. What is development length?
asked in Tecnimont
Q4. What is lap length?
asked in Tecnimont
Q5. What is lap langth??

Interview questions from similar companies

Interview Questionnaire 

1 Question

  • Q1. Hard core techanical

I applied via Walk-in and was interviewed before Apr 2020. There was 1 interview round.

Interview Questionnaire 

6 Questions

  • Q1. Can you explain Man day
  • Q2. Can you explain manpower mobilization.
  • Ans. 

    Manpower mobilization refers to the process of deploying and managing personnel for a specific project or task.

    • Identifying the required personnel for a project

    • Recruiting and hiring personnel

    • Training and orienting personnel to the project

    • Assigning roles and responsibilities to personnel

    • Managing personnel performance and productivity

    • Ensuring compliance with labor laws and regulations

    • Examples include mobilizing a construc...

  • Answered by AI
  • Q3. How to cost control in project
  • Ans. 

    Cost control in project can be achieved through effective planning, monitoring and controlling of project expenses.

    • Create a detailed project budget and stick to it

    • Track expenses regularly and adjust budget as needed

    • Identify and eliminate unnecessary expenses

    • Negotiate with vendors for better pricing

    • Implement cost-saving measures without compromising quality

    • Use project management tools to monitor expenses and progress

    • Reg...

  • Answered by AI
  • Q4. Can you explain how to handle clinent
  • Ans. 

    Handling clients requires effective communication, understanding their needs, and providing timely solutions.

    • Listen actively to their concerns and requirements

    • Communicate clearly and professionally

    • Provide timely updates and solutions

    • Build a strong relationship based on trust and respect

    • Be proactive in identifying and addressing potential issues

    • Ensure customer satisfaction by going above and beyond expectations

  • Answered by AI
  • Q5. Flow chart for manpower mobilization
  • Ans. 

    Manpower mobilization flow chart involves identifying needs, planning, recruitment, training, and deployment.

    • Identify the need for manpower

    • Plan the recruitment process

    • Source and screen candidates

    • Conduct interviews and assessments

    • Select and hire candidates

    • Provide training and orientation

    • Deploy manpower to required locations

  • Answered by AI
  • Q6. Prepared organisation chat for project handling

Interview Preparation Tips

Interview preparation tips for other job seekers - Please see all questions

I applied via Referral and was interviewed in Dec 2020. There were 4 interview rounds.

Interview Questionnaire 

3 Questions

  • Q1. Cube Compressive achieving Percentage time periods?
  • Ans. 

    Cube compressive achieving percentage time periods

    • The question is asking about the percentage of time periods in which cube compressive strength is achieved

    • Cube compressive strength refers to the ability of a cube-shaped material to withstand compression

    • The answer may involve calculating the percentage of time periods in which the cube meets the required compressive strength

    • Examples of data points needed: time periods,

  • Answered by AI
  • Q2. M20 grade and M means and 20 means and unit
  • Q3. 1:1.5:3 ,M-Mix,20 -Compresive strength,N/mm²

Interview Preparation Tips

Interview preparation tips for other job seekers - Be face Bolt don't jerk anyone becoz they also Human

I applied via Company Website and was interviewed before Sep 2020. There was 1 interview round.

Interview Questionnaire 

1 Question

  • Q1. They asked for previous company work management, work culture, work timing & some technical questions

Interview Preparation Tips

Interview preparation tips for other job seekers - Its not so difficult
Just share your work experience
Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Ammonia process
Round 3 - HR 

(2 Questions)

  • Q1. How much salary expectations?
  • Q2. Salary Negotiable

Interview Preparation Tips

Interview preparation tips for other job seekers - All the best
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Naukri.com and was interviewed in Jul 2023. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Prepare basics properly before going for interview, they mostly ask less questions with more depth.
  • Q2. Draw BMD for sway frame.
  • Ans. 

    BMD for sway frame is a diagram showing the variation of bending moment along the length of the frame.

    • BMD for sway frame will have a shape similar to a zigzag pattern due to the presence of sway in the frame.

    • The bending moment will be maximum at the points where the frame experiences maximum sway.

    • The BMD can be drawn by analyzing the internal forces and moments acting on the frame.

  • Answered by AI
Round 3 - One-on-one 

(3 Questions)

  • Q1. Draw piperack elevations
  • Ans. 

    Drawing piperack elevations involves creating detailed drawings of the structure from different viewpoints.

    • Start by determining the dimensions and layout of the piperack

    • Use software like AutoCAD to create accurate and detailed drawings

    • Include all necessary details such as pipe sizes, supports, and connections

    • Label all components clearly for easy understanding

    • Review and revise the drawings as needed for accuracy

  • Answered by AI
  • Q2. Anchor bolt design
  • Q3. Base plate design
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
-

I appeared for an interview in Apr 2024.

Round 1 - One-on-one 

(2 Questions)

  • Q1. Control Valve sizing
  • Q2. Flowmeter selection
Round 2 - HR 

(2 Questions)

  • Q1. Reason for shifting
  • Ans. 

    I shifted to pursue new opportunities for growth and development in my career.

    • Seeking new challenges and responsibilities

    • Exploring different industries or technologies

    • Relocation for personal reasons or family commitments

  • Answered by AI
  • Q2. Expected salary
Interview experience
1
Bad
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed before Nov 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Basics of what ur past experience
  • Q2. Basic of shuttering and concreting
Round 3 - Technical 

(1 Question)

  • Q1. What u r past experience

Interview Preparation Tips

Interview preparation tips for other job seekers - Cheapest HRs team in entire Ahemdabad have worked with no. Of company but this company HRs is the worst of them all..
No fixed timing of work. Only top management is supportive down the line everyone is of cheap mentality. Not recommend to join the company as u will regret later. Not even cable to achieve 1 star

Tecnimont Interview FAQs

What are the top questions asked in Tecnimont Revit Designer interview?

Some of the top questions asked at the Tecnimont Revit Designer interview -

  1. What is BBS? & explain ...read more
  2. What is developement leng...read more
  3. What is development leng...read more

Tell us how to improve this page.

Interview Questions from Similar Companies

AECOM Interview Questions
4.2
 • 116 Interviews
Apco Infratech Interview Questions
3.7
 • 114 Interviews
TechnipFMC Interview Questions
4.0
 • 71 Interviews
Bechtel Interview Questions
3.9
 • 68 Interviews
Samsung E&A Interview Questions
4.0
 • 60 Interviews
Wood Group Interview Questions
3.8
 • 59 Interviews
View all
Tecnimont Revit Designer Salary
based on 4 salaries
₹1.1 L/yr - ₹9.5 L/yr
8% more than the average Revit Designer Salary in India
View more details

Tecnimont Revit Designer Reviews and Ratings

based on 2 reviews

4.5/5

Rating in categories

3.0

Skill development

3.0

Work-life balance

4.0

Salary

5.0

Job security

3.0

Company culture

3.5

Promotions

3.5

Work satisfaction

Explore 2 Reviews and Ratings
Deputy Chief Engineer
183 salaries
unlock blur

₹13.6 L/yr - ₹36 L/yr

Principal Engineer
128 salaries
unlock blur

₹8.5 L/yr - ₹25.2 L/yr

Senior Engineer
84 salaries
unlock blur

₹7 L/yr - ₹18 L/yr

Additional Chief Engineer
53 salaries
unlock blur

₹21.5 L/yr - ₹46 L/yr

Assistant Manager
52 salaries
unlock blur

₹10 L/yr - ₹27 L/yr

Explore more salaries
Compare Tecnimont with

AECOM

4.2
Compare

L&T Energy Hydrocarbon

3.9
Compare

Apco Infratech

3.7
Compare

Saipem

4.1
Compare
Did you find this page helpful?
Yes No
write
Share an Interview