Upload Button Icon Add office photos

SRF

Compare button icon Compare button icon Compare

Filter interviews by

SRF Mechanical Technician Interview Questions, Process, and Tips

Updated 15 Sep 2023

Top SRF Mechanical Technician Interview Questions and Answers

SRF Mechanical Technician Interview Experiences

4 interviews found

Interview experience
5
Excellent
Difficulty level
Hard
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Walk-in and was interviewed in Aug 2023. There was 1 interview round.

Round 1 - Technical 

(4 Questions)

  • Q1. Pump maintenance work
  • Q2. Reactor mechanical seal assembly work
  • Ans. 

    Reactor mechanical seal assembly work involves installing, maintaining, and troubleshooting mechanical seals in reactor systems.

    • Understanding the components of a mechanical seal assembly

    • Properly installing and aligning the mechanical seal

    • Performing routine maintenance on the seal to prevent leaks

    • Troubleshooting issues such as leaks or malfunctions

    • Following safety protocols when working with reactor systems

  • Answered by AI
  • Q3. Dial gauge alignment work
  • Ans. 

    Dial gauge alignment work involves ensuring the accuracy of measurements by adjusting the position of the gauge.

    • Ensure the dial gauge is securely mounted to a stable surface

    • Use a calibration standard to check the accuracy of the gauge

    • Adjust the position of the gauge by loosening the mounting screws and realigning as needed

    • Verify the accuracy of the gauge after realignment

  • Answered by AI
  • Q4. Vaccum pump vaccum problem
  • Ans. 

    Possible causes of vacuum pump vacuum problem and troubleshooting steps

    • Check for leaks in the vacuum system

    • Inspect the vacuum pump for any damage or wear

    • Ensure the pump is properly lubricated

    • Check the vacuum pump's inlet filter for clogs

    • Verify that the pump is receiving adequate power supply

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Good company to SRF
Interview experience
3
Average
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Technical questions about mechanical related
Round 3 - One-on-one 

(1 Question)

  • Q1. Skills and competencies
Round 4 - HR 

(1 Question)

  • Q1. Payroll and expectations

Interview Preparation Tips

Interview preparation tips for other job seekers - Always believe in your self, learn fast Adobe new technologies

Mechanical Technician Interview Questions Asked at Other Companies

asked in Kent plc
Q1. 1. During confined space job , what is the role of safety watch ? ... read more
Q2. How many types of valve? What are they?
asked in AOS Orwell
Q3. what is a compressor? and give example of instrument that works o ... read more
Q4. How many types of heat exchanger? What are they?
Q5. 1) What is process before starting Excenger work ?
Interview experience
1
Bad
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Gearbox, pump, id & fan blowers,compreshar,all plant,breakdown, maintenance
  • Q2. Valve, paip line

Interview Preparation Tips

Interview preparation tips for other job seekers - check my &help

I applied via Walk-in and was interviewed in Dec 2020. There was 1 interview round.

Interview Questionnaire 

1 Question

  • Q1. Glass line reactor mechanical seal fitting parameter
  • Ans. 

    Glass line reactor mechanical seal fitting parameters are critical for ensuring proper functioning and preventing leaks.

    • The fitting parameters depend on the type of mechanical seal being used.

    • Factors such as seal face material, seal face loading, and seal face geometry must be considered.

    • Proper installation and alignment of the mechanical seal is also important.

    • Regular maintenance and monitoring of the seal is necessar...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Run out chek
Consenrtycity chek
Seqvernetion chek

SRF interview questions for designations

 Mechanical Engineer

 (1)

 Instrumentation Technician

 (2)

 Electrical Technician

 (1)

 Process Technician

 (1)

 Junior Mechanical Engineer

 (1)

 Executive Engineer Mechanical

 (1)

 Mechanical Maintenance Supervisor

 (1)

 Junior Engineer Mechanical Maintenance

 (1)

Interview questions from similar companies

I applied via Walk-in

Interview Questionnaire 

4 Questions

  • Q1. Maintenance machical packing department
  • Q2. All conver maintenance packing department
  • Q3. All pump maintenance and wpb
  • Q4. Senior technician mechanical maintenance

Interview Preparation Tips

Interview preparation tips for other job seekers - All mechanical maintenance packing department and wpb rmg

I applied via Recruitment Consultant and was interviewed before Oct 2020. There was 1 interview round.

Interview Questionnaire 

1 Question

  • Q1. Experience in Piping Design tool
  • Ans. 

    I have extensive experience in using various piping design tools.

    • Proficient in using AutoCAD for piping design

    • Familiar with 3D modeling software like SolidWorks for creating detailed piping layouts

    • Skilled in using piping design software such as Caesar II for stress analysis

    • Experience in using PDMS (Plant Design Management System) for piping design and layout

    • Knowledge of industry standards and codes related to piping de

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Be honest and share your vision in terms of individual

I applied via Referral and was interviewed before Oct 2020. There were 4 interview rounds.

Interview Questionnaire 

2 Questions

  • Q1. About your introduction, location,family details & Salary discussions
  • Q2. Technical questions related to Vacancy

Interview Preparation Tips

Interview preparation tips for other job seekers - Search aptitude questions on google it will helpful

Interview Questionnaire 

7 Questions

  • Q1. About electrical maintenance and experience.
  • Q2. What is Mcb and mccb ?
  • Ans. 

    Mcb stands for Miniature Circuit Breaker and MCCB stands for Molded Case Circuit Breaker.

    • Mcb is a type of circuit breaker that is used for low voltage applications.

    • MCCB is a type of circuit breaker that is used for high voltage applications.

    • Both Mcb and MCCB are used to protect electrical circuits from overloads and short circuits.

    • Mcb is usually rated for currents up to 100 amps, while MCCB can handle currents up to 25...

  • Answered by AI
  • Q3. What is different between current and voltage.
  • Ans. 

    Current and voltage are two fundamental concepts in electricity. Current is the flow of electric charge, while voltage is the potential difference that drives the flow.

    • Current is the rate of flow of electric charge, measured in amperes (A).

    • Voltage is the force or pressure that pushes the electric charge to flow, measured in volts (V).

    • Current flows through a conductor, while voltage exists across a conductor.

    • Current is ...

  • Answered by AI
  • Q4. What is unit and how maser current and voltage ?
  • Ans. 

    A unit is a standard measurement used to quantify physical quantities. Current is measured in amperes (A) and voltage is measured in volts (V).

    • A unit is a fixed quantity used as a standard of measurement.

    • Current is the flow of electric charge in a circuit and is measured in amperes (A).

    • Voltage is the electric potential difference between two points in a circuit and is measured in volts (V).

    • The unit of current, ampere, ...

  • Answered by AI
  • Q5. How many types of transformer ?
  • Ans. 

    There are several types of transformers used in electrical systems.

    • Power Transformers

    • Distribution Transformers

    • Instrument Transformers

    • Auto Transformers

    • Isolation Transformers

    • Step-up and Step-down Transformers

    • Three-phase Transformers

    • Single-phase Transformers

  • Answered by AI
  • Q6. What is D.OL starter?
  • Ans. 

    D.OL starter is a type of motor starter used to start and stop three-phase motors.

    • D.OL stands for Direct-On-Line.

    • It is the simplest and most common type of motor starter.

    • It directly connects the motor to the power supply, providing full voltage to the motor.

    • It is suitable for small to medium-sized motors.

    • It does not provide any protection against overloading or short circuits.

    • It is commonly used in applications such as

  • Answered by AI
  • Q7. What is amper?
  • Ans. 

    An ampere (amp) is the unit of electric current in the International System of Units (SI).

    • Amperes measure the rate of flow of electric charge.

    • It is named after the French physicist André-Marie Ampère.

    • One ampere is defined as one coulomb of charge passing through a point in one second.

    • Amperes are used to measure the current flowing through electrical circuits.

    • Common household appliances like light bulbs and refrigerator...

  • Answered by AI
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I appeared for an interview before Mar 2022.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - One-on-one 

(1 Question)

  • Q1. About *Current Roles and Responsibilities * Market Knowledge * Product Knowledge * Channel Expansion * Demand Generation * Secondary
Round 3 - HR 

(1 Question)

  • Q1. About * Package * Why need to job change

Interview Preparation Tips

Interview preparation tips for other job seekers - Good Company..
Regarding
* Employee care
* Reward and Recognition from Top end was good
* Communication is same from top to bottom.
* Top end people Identify the employees strengths and lags.
Provide necessary inputs
Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(2 Questions)

  • Q1. What about power system
  • Q2. What is protection system
  • Ans. 

    A protection system is a set of devices and measures designed to prevent damage or harm to equipment, personnel, or the environment in case of a fault or abnormal condition.

    • Protection systems can include circuit breakers, fuses, relays, and alarms.

    • They are commonly used in electrical systems to prevent overloads, short circuits, and ground faults.

    • Protection systems are essential for ensuring the safety and reliability ...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Please tell true answer

SRF Interview FAQs

How many rounds are there in SRF Mechanical Technician interview?
SRF interview process usually has 2-3 rounds. The most common rounds in the SRF interview process are Resume Shortlist, Technical and One-on-one Round.
What are the top questions asked in SRF Mechanical Technician interview?

Some of the top questions asked at the SRF Mechanical Technician interview -

  1. Glass line reactor mechanical seal fitting paramet...read more
  2. Reactor mechanical seal assembly w...read more
  3. Vaccum pump vaccum prob...read more

Tell us how to improve this page.

SRF Mechanical Technician Interview Process

based on 5 interviews

2 Interview rounds

  • Resume Shortlist Round
  • Technical Round
View more

Interview Questions from Similar Companies

Asian Paints Interview Questions
4.0
 • 648 Interviews
Berger Paints Interview Questions
3.7
 • 261 Interviews
DCM Shriram Interview Questions
4.2
 • 88 Interviews
Atul Interview Questions
3.9
 • 86 Interviews
Tata Chemicals Interview Questions
4.1
 • 62 Interviews
View all
SRF Mechanical Technician Salary
based on 96 salaries
₹2.6 L/yr - ₹6.2 L/yr
11% more than the average Mechanical Technician Salary in India
View more details

SRF Mechanical Technician Reviews and Ratings

based on 23 reviews

4.3/5

Rating in categories

3.9

Skill development

4.2

Work-life balance

4.3

Salary

4.4

Job security

3.9

Company culture

4.0

Promotions

4.0

Work satisfaction

Explore 23 Reviews and Ratings
Junior Engineer
989 salaries
unlock blur

₹2.1 L/yr - ₹9.4 L/yr

Senior Executive
415 salaries
unlock blur

₹4.5 L/yr - ₹15.2 L/yr

Junior Officer
191 salaries
unlock blur

₹2.5 L/yr - ₹9 L/yr

Technician
185 salaries
unlock blur

₹2.4 L/yr - ₹6.6 L/yr

Assistant Manager
169 salaries
unlock blur

₹7.3 L/yr - ₹16 L/yr

Explore more salaries
Compare SRF with

Asian Paints

4.0
Compare

Berger Paints

3.7
Compare

Pidilite Industries

4.3
Compare

Kansai Nerolac Paints

3.8
Compare
Did you find this page helpful?
Yes No
write
Share an Interview