Add office photos
Filter interviews by
Special Technical Services Llc, Oman QA QC Inspector Interview Questions and Answers
Special Technical Services Llc, Oman QA QC Inspector Interview Experiences
1 interview found
Anonymous
Selected
I applied via Referral and was interviewed before Apr 2022. There were 2 interview rounds.
(2 Questions)
- Q1. Explain Hic testing requirements
- Ans.
HIC testing requirements ensure safety of vehicle occupants during crashes.
HIC stands for Head Injury Criterion and is a measure of the likelihood of head injury during a crash.
HIC testing is required for all vehicles to ensure that the occupants are safe in the event of a crash.
The maximum allowable HIC value varies depending on the type of vehicle and the seating position.
HIC testing is typically performed using a cr...
- Q2. Dss material fabrication requirements
- Ans.
DSS material fabrication requirements
DSS (Duplex Stainless Steel) material should be fabricated in a clean environment to avoid contamination
Welding should be done using low heat input to prevent distortion and cracking
Post-weld heat treatment is required to restore the material's corrosion resistance
Fabrication should be done according to the relevant codes and standards such as ASME Section VIII Div.1 and AWS D1.6
Ins...
Interview Preparation Tips
Skills evaluated in this interview
Top trending discussions
Interview questions from similar companies
(2 Questions)
- Q1. About C276 material specifications
- Q2. About ASME section-ix
(2 Questions)
- Q1. AC power kese check kar te hai
- Q2. Pawer meter ko kitne percent karke bhi aisi Power check
Interview Preparation Tips
(1 Question)
- Q1. Explain stress and strain
- Ans.
Stress is the force applied to a material, while strain is the resulting deformation or change in shape.
Stress is the force applied per unit area on a material.
Strain is the measure of deformation or change in shape of a material.
Stress and strain are related by the material's modulus of elasticity.
Example: When a rubber band is stretched, the force applied is the stress and the resulting elongation is the strain.
I applied via Campus Placement and was interviewed before Oct 2023. There were 2 interview rounds.
I'm descision about product project what need to employees to project how to manage shift....aslo A,B,C what give to safety leady employees....and how to work as a family is in one roof
(2 Questions)
- Q1. Introduction and about family
- Q2. What's your acceptance about salary
- Ans.
I am open to discussing salary based on the responsibilities and expectations of the role.
I believe that compensation should be fair and reflective of the value I bring to the company.
I am willing to negotiate based on the benefits package and opportunities for growth within the company.
I am open to discussing salary range during the interview process to ensure alignment with expectations.
Interview Preparation Tips
Selected
I applied via Walk-in and was interviewed in Apr 2023. There were 2 interview rounds.
(2 Questions)
- Q1. All Question Related to resume and experience in your privous jobs And Project.
- Q2. All Testing, site related work question, MMS, DC & AC. Quality related documents work. FQP.
Interview Preparation Tips
- All related to role & responsibi
- All test knowledge. If you work
Role and responsibilities.
Focus your target.
Arvind Shukla
Selected
I applied via Job Portal and was interviewed in Aug 2023. There were 3 interview rounds.
(1 Question)
- Q1. What is PWHT.? POST heating and Pre heating? PMI NDT P-91 Material Site Observation Report MIS KPI SITE TRAINING WELDING
- Ans.
PWHT stands for Post Weld Heat Treatment. It is a process used to relieve residual stresses and improve the mechanical properties of welds.
PWHT is commonly used in the welding industry to prevent cracking and improve the overall quality of welds.
Post heating and pre heating are processes used before and after welding to control the cooling rate of the material and reduce the risk of cracking.
PMI stands for Positive Mat...
(1 Question)
- Q1. SALARY NEGOTIATION TALK TO JOINN ON DIRECT THERMAX ROLE. DONT JOIN ON THIRD PARTY ROLE BECAUSE JOB NOT SECURE ON THIRD PARTY ROLE
Selected
I was interviewed before Oct 2022.
(2 Questions)
- Q1. Quality line incharge
- Q2. Yes quality line incharge
(1 Question)
- Q1. Qc line incharge
(1 Question)
- Q1. Press shop Qc line incharge
Interview Preparation Tips
Selected
I applied via campus placement at Indo Danish Tool Room, Jamshedpur and was interviewed before Dec 2022. There were 2 interview rounds.
(1 Question)
- Q1. Qualities and project improve project and quality improvement
Selected
I applied via Approached by Company and was interviewed before Dec 2021. There were 3 interview rounds.
(2 Questions)
- Q1. HR calls after finding the suitable candidate and ask them to share their updated resume with other credentials such as education certificate and experience certificate etc.
- Q2. General introduction
(3 Questions)
- Q1. After HR arrange for the technical interview and panel of 3 people take interview which comprises of HR and technical persons such as Quality DGM and M4 level person.
- Q2. 1.Optimization of Cement means ? 2. Concrete design miix as per CBC 3 Batching plant and calibration 4. Soil testing etc
- Ans.
Optimization of cement refers to improving the quality and efficiency of cement production.
Reducing the amount of clinker used in cement production
Using alternative fuels and raw materials
Improving the grinding process
Controlling the chemical composition of raw materials
Minimizing energy consumption
Maximizing output while maintaining quality
Ensuring compliance with industry standards and regulations
- Q3. What's are the checks in Site Inspection for RCC work of Bridge culvert and major bridges
- Ans.
Checks in Site Inspection for RCC work of Bridge culvert and major bridges
Check for proper reinforcement placement and spacing
Check for proper concrete mix and slump
Check for proper curing of concrete
Check for proper alignment and level of formwork
Check for proper placement and compaction of concrete
Check for proper finishing of concrete surface
Check for cracks and defects in concrete
Check for proper drainage system
Che
Interview Preparation Tips
Special Technical Services Llc, Oman Interview FAQs
Tell us how to improve this page.
Interview Questions for Popular Designations
- Quality Inspector Interview Questions
- QC Inspector Interview Questions
- QA QC Engineer Interview Questions
- Quality Control Inspector Interview Questions
- QC Welding Inspector Interview Questions
- QC Inspector Instrumentation Interview Questions
- QA QC Welding Inspector Interview Questions
- Quality Assurance Inspector Interview Questions
- Show more
People are getting interviews through
Interview Questions from Similar Companies
|
Planning Engineer
7
salaries
|  ₹14 L/yr - ₹16 L/yr |
|
HSE Advisor
6
salaries
| ₹4.4 L/yr - ₹12 L/yr |
|
Instrument Engineer
5
salaries
| ₹6 L/yr - ₹18 L/yr |
|
QC Civil Inspector
4
salaries
| ₹17.4 L/yr - ₹24 L/yr |
|
Instrumentation Technician
4
salaries
| ₹5 L/yr - ₹8 L/yr |
Larsen & Toubro Limited
TCS
BHEL
Reliance Industries
Calculate your in-hand salary
- Home >
- Interviews >
- Special Technical Services Llc, Oman Interview Questions >
- Special Technical Services Llc, Oman QA QC Inspector Interview Questions
