IXAR Technician Interview Questions and Answers

Current is the flow of electric charge in a circuit.

• Current is measured in Amperes (A)

• It is the rate of flow of electric charge through a conductor

• There are two types of current - AC (alternating current) and DC (direct current)

• Examples of current include the flow of electrons in a wire when a light bulb is turned on

Voltage is the difference in electric potential between two points in a circuit, measured in volts.

• Voltage is the driving force that pushes electric current through a circuit

• It is measured in volts (V)

• Voltage can be positive or negative, depending on the direction of current flow

• Higher voltage means more potential energy available to move electrons

• Example: A battery provides voltage to power a light bulb

Ohm's law states that the current flowing through a conductor is directly proportional to the voltage applied across it, and inversely proportional to the resistance of the conductor.

• Ohm's law is expressed as V = I * R, where V is voltage, I is current, and R is resistance.

• It helps in calculating the current flowing through a circuit when the voltage and resistance are known.

• It can also be used to determine the resista...read more

One of my biggest achievements was successfully leading a team to complete a complex project ahead of schedule and under budget.

• Led a team to complete a complex project ahead of schedule

• Managed resources effectively to stay under budget

• Received recognition for successful project completion

Refrigeration cycle is a process in which a refrigerant absorbs heat from a low-temperature space and rejects it in a high-temperature space.

• The refrigeration cycle consists of four main components: compressor, condenser, expansion valve, and evaporator.

• The refrigerant starts as a low-pressure gas in the evaporator where it absorbs heat from the space being cooled.

• The compressor then compresses the refrigerant into a h...read more

Four stroke cycle engine works by completing four distinct processes - intake, compression, power, and exhaust strokes.

• Intake stroke: Air-fuel mixture is drawn into the cylinder as the piston moves downward.

• Compression stroke: The intake valve closes and the piston compresses the mixture, preparing it for ignition.

• Power stroke: The spark plug ignites the compressed mixture, causing an explosion that drives the piston d...read more

A centrifugal pump is a mechanical device used to transport fluids by converting rotational kinetic energy into hydrodynamic energy.

• Centrifugal pumps are commonly used in various industries, including oil and gas, water treatment, and HVAC systems.

• They work by using an impeller to rotate and create a centrifugal force, which pushes the fluid towards the pump outlet.

• The fluid enters the pump through the suction inlet an...read more

There are several types of valves used in mechanical systems.

• Gate valve: used to control the flow of fluid by lifting or lowering a gate

• Ball valve: uses a ball to control the flow of fluid

• Butterfly valve: uses a disc to control the flow of fluid

• Check valve: allows fluid to flow in one direction only

• Globe valve: controls flow by raising or lowering a plug

• Needle valve: uses a long, tapered needle to control flow

• Diaphragm...read more

A ball valve is a type of valve that uses a ball-shaped disc to control the flow of fluid through a pipe.

• Ball valves are commonly used in industrial applications for their durability and reliability.

• They have a simple design, consisting of a ball with a hole in the middle that can be rotated to control the flow of fluid.

• Ball valves can be either full port or reduced port, depending on the size of the ball and the hole.

• ...read more

A shell and tube heat exchanger is a device used to transfer heat between two fluids.

• Consists of a shell (outer vessel) and tubes (inner vessels)

• One fluid flows through the tubes while the other flows around the tubes in the shell

• Heat is transferred from one fluid to the other through the tube walls

• Commonly used in industries such as power generation, chemical processing, and HVAC

• Example: Cooling water in a power plant

There are several types of heat exchangers, including shell and tube, plate and frame, and finned tube.

• Shell and tube heat exchangers are the most common type and consist of a shell with tubes inside.

• Plate and frame heat exchangers use thin plates to transfer heat between fluids.

• Finned tube heat exchangers have tubes with fins attached to increase surface area for heat transfer.

• Other types include spiral, double pipe, ...read more

PPE stands for Personal Protective Equipment.

• PPE is equipment worn to minimize exposure to hazards that may cause serious workplace injuries or illnesses.

• Examples of PPE include safety glasses, gloves, hard hats, respirators, and safety shoes.

• PPE should be selected based on the specific hazards present in the workplace.

• Employers are responsible for providing PPE to their employees and ensuring that it is properly maint...read more

An axial flow pump is a type of pump that uses an impeller to create fluid flow parallel to the pump shaft.

• Axial flow pumps are commonly used in applications where large volumes of fluid need to be moved at low to medium pressures.

• They are often used in irrigation systems, drainage systems, and cooling systems.

• The impeller of an axial flow pump has blades that resemble a propeller, which helps in generating the axial f...read more

A check valve is a mechanical device that allows fluid to flow in one direction only.

• Check valves are commonly used in plumbing systems to prevent backflow of water.

• They are also used in hydraulic systems to prevent reverse flow of fluid.

• Check valves can be classified into different types such as swing check valves, lift check valves, and ball check valves.

• These valves work by using a disc or a ball that opens and clos...read more

Positive displacement pump is a type of pump that moves fluid by trapping a fixed amount of it and then forcing it into the discharge pipe.

• Positive displacement pumps operate by trapping a specific volume of fluid and then forcing it into the discharge pipe.

• These pumps are capable of generating high pressures and are used in various industries such as oil and gas, chemical, and food processing.

• Examples of positive disp...read more

A globe valve is a type of valve used to regulate or stop the flow of fluid in a pipeline.

• It has a spherical body with an internal baffle that directs the flow of fluid.

• The valve can be opened or closed by rotating the stem.

• It provides a tight seal when closed, preventing leakage.

• Globe valves are commonly used in applications where throttling or regulating flow is required.

• They are often found in water systems, steam s

PPE stands for Personal Protective Equipment. It refers to protective clothing, helmets, goggles, or other equipment designed to protect the wearer's body from injury or infection.

• PPE is used in various industries to protect workers from hazards.

• Examples of PPE include safety glasses, gloves, hard hats, respirators, and earplugs.

• PPE should be selected based on the specific hazards present in the workplace.

• Proper traini...read more

I have 5 years of experience working in the oil and gas field, specializing in maintenance and troubleshooting of equipment.

• Experience in maintenance and troubleshooting of equipment in oil and gas field

• Knowledge of safety protocols and regulations in the industry

• Familiarity with various tools and technologies used in the field

• Worked on projects involving drilling, extraction, and transportation of oil and gas

• Collabora...read more

As a Mechanical Technician Static and Rotating Foreman at Qatar Gas North, my role involves overseeing maintenance and repair of static and rotating equipment to ensure smooth operations.

• Oversee maintenance and repair of static and rotating equipment

• Ensure smooth operations of equipment

• Supervise a team of technicians

• Implement safety procedures and protocols

• Coordinate with other departments for maintenance schedules