Filter interviews by
Clear (1)
I applied via Company Website and was interviewed in Nov 2023. There were 3 interview rounds.
Top trending discussions
A turbine is a device that converts the energy from a fluid flow into useful work, typically by rotating a shaft.
Turbines are commonly used in power generation, aviation, and marine propulsion.
They work on the principle of Newton's third law of motion, where the reaction force of the fluid flow causes the turbine blades to rotate.
Turbines can be classified into various types such as steam turbines, gas turbines, and hy...
I applied via Referral and was interviewed in Mar 2021. There was 1 interview round.
The operation refers to a specific action or procedure performed to achieve a desired outcome.
An operation is a planned activity that involves a series of steps or actions.
It is typically performed by a person or a machine to accomplish a specific task.
Operations can vary across different fields such as medicine, manufacturing, technology, etc.
Examples of operations include surgical procedures, manufacturing processes,
I applied via Walk-in and was interviewed in Aug 2024. There was 1 interview round.
The question seems to be asking about the diameter of a machine part called a mudgan in a mudgan machine.
The question is likely asking for the diameter of the mudgan in the mudgan machine.
Provide information about the mudgan machine and its components.
Explain the purpose of the mudgan in the machine.
Discuss any specific measurements or specifications related to the mudgan.
The length of a lancing pipe varies depending on the specific application and requirements.
The length of a lancing pipe can range from a few inches to several feet.
It is important to consider the depth of the operation and the reach needed when determining the length of the lancing pipe.
Different industries and tasks may require different lengths of lancing pipes, such as in welding, plumbing, or industrial cleaning.
The air pressure in a drilling machine is typically controlled by the operator and can vary depending on the specific machine and drilling requirements.
Air pressure in drilling machines is usually measured in pounds per square inch (psi).
The optimal air pressure for a drilling machine can vary based on factors such as the type of material being drilled, the size of the drill bit, and the depth of the hole.
Operators sho...
The length of the drill rod depends on the specific operation and equipment being used.
The length of the drill rod can vary based on the depth of the hole being drilled.
Different types of drilling operations may require different lengths of drill rods.
It is important to consider the reach and capabilities of the drilling equipment when determining the length of the drill rod.
I applied via Walk-in and was interviewed in Nov 2023. There were 2 interview rounds.
I applied via Recruitment Consulltant and was interviewed in Feb 2022. There were 2 interview rounds.
The question covers various topics related to pumps, valves, and chemical properties.
pH is a measure of acidity or alkalinity of a solution.
Tar density is the mass of tar per unit volume of a substance.
Tar production process involves heating organic materials in the absence of air.
Types of pumps include centrifugal, positive displacement, and axial flow pumps.
Types of valves include ball, gate, globe, and check valves.
...
I applied via Naukri.com and was interviewed before Jan 2021. There were 3 interview rounds.
ICP OES is a technique used for chemical analysis of chromite ore.
ICP OES stands for Inductively Coupled Plasma Optical Emission Spectroscopy.
It is a powerful analytical technique used for the determination of trace elements in a variety of matrices.
ICP OES can be used to determine the concentration of elements such as Cr, Fe, Mg, Al, and Si in chromite ore.
The technique involves the excitation of atoms in a sample usi...
ICP-OES is a technique used for elemental analysis in which a sample is vaporized and excited by a plasma to emit light.
ICP-OES stands for Inductively Coupled Plasma Optical Emission Spectroscopy.
It is used to determine the concentration of elements in a sample.
The sample is vaporized and excited by a plasma to emit light, which is then analyzed to determine the elemental composition.
ICP-OES is commonly used in environ...
Weight chemical analysis of chromite ore involves determining the percentage of various elements present in the ore.
The ore is first crushed and ground into a fine powder.
The powder is then mixed with various chemicals to dissolve the elements of interest.
The resulting solution is then analyzed using various techniques such as atomic absorption spectroscopy or inductively coupled plasma mass spectrometry.
The percentage...
I applied via Walk-in and was interviewed in Mar 2023. There were 2 interview rounds.
Rankine cycle is a thermodynamic cycle used in power plants to generate electricity.
Rankine cycle is a closed-loop cycle that uses steam to generate power.
The cycle consists of four processes: heating, vaporization, expansion, and condensation.
The efficiency of the Rankine cycle can be improved by increasing the temperature and pressure of the steam.
The Rankine cycle is commonly used in power plants to generate electri...
I applied via Job Portal and was interviewed before Nov 2021. There were 3 interview rounds.
Direct through campus placement and group discussion.
posted on 19 May 2017
I was interviewed in Oct 2016.
Experienced retail professional with strong leadership skills and a passion for customer service.
Over 5 years of retail management experience
Proven track record of increasing sales and improving customer satisfaction
Strong leadership and team-building skills
Passionate about providing excellent customer service
Bachelor's degree in Business Administration
Alumina is obtained from bauxite through the Bayer process.
Bauxite is crushed and mixed with sodium hydroxide to form a slurry.
The slurry is heated and pressurized in a digester to dissolve the alumina content.
The resulting solution is cooled and filtered to remove impurities.
The purified solution is then heated to precipitate the alumina as a white powder.
The alumina powder is washed, dried, and calcined to produce pu...
The reaction for Al extraction from alumina involves the reduction of alumina using carbon or electrolysis.
Alumina (Al2O3) is first converted into aluminum chloride (AlCl3) by reacting with hydrochloric acid.
The aluminum chloride is then reduced to aluminum metal by either carbon reduction or electrolysis.
In carbon reduction, carbon (usually in the form of coke) is heated with the aluminum chloride to produce aluminum ...
There are four main types of cast iron: gray iron, white iron, ductile iron, and malleable iron.
Gray iron is the most common type and has excellent castability and good machinability.
White iron is very hard and brittle, often used for wear-resistant applications.
Ductile iron has high strength and ductility, making it suitable for a wide range of applications.
Malleable iron is heat-treated to improve its strength and du
based on 1 interview
Interview experience
based on 1 review
Rating in categories
Assistant Manager
281
salaries
| ₹0 L/yr - ₹0 L/yr |
Associate Manager
253
salaries
| ₹0 L/yr - ₹0 L/yr |
Deputy Manager
166
salaries
| ₹0 L/yr - ₹0 L/yr |
Mining Engineer
125
salaries
| ₹0 L/yr - ₹0 L/yr |
Manager
84
salaries
| ₹0 L/yr - ₹0 L/yr |
Vedanta Limited
Hindalco Industries
Tata Steel
JSW Steel