i
Fldec Systems
Filter interviews by
I applied via Naukri.com
A capacitor stores electrical energy in an electric field and releases it when needed.
Capacitors are used to filter out noise and stabilize voltage in electronic circuits.
The capacitance value determines how much charge a capacitor can store.
Different types of capacitors have different properties and are used for specific applications.
Choosing the right capacitor involves considering factors such as capacitance, voltag...
I applied via Walk-in and was interviewed in Mar 2021. There was 1 interview round.
Use a step-down transformer to reduce voltage and a rectifier circuit to convert AC to DC.
Select a transformer with a 230V AC primary winding and a 24V DC secondary winding
Connect the AC input to the primary winding and the DC output to the secondary winding
Use a rectifier circuit to convert the AC output of the transformer to DC
Add a smoothing capacitor to reduce ripple in the DC output
Top trending discussions
I applied via Campus Placement and was interviewed before Feb 2023. There were 2 interview rounds.
Basic arithmetic aptitude and electronics based questions
Quantitative aptitude with general and technical questions
I applied via Approached by Company and was interviewed in Mar 2022. There were 2 interview rounds.
The operating frequency of USB Type C is 10 Gbps.
USB Type C has a maximum data transfer rate of 10 Gbps
It is also backward compatible with USB 2.0 and 3.0
The frequency can vary depending on the device and cable used
The minimum clearance for DDR Data group signals Routing is 6 mils.
DDR Data group signals Routing requires a minimum clearance of 6 mils to avoid crosstalk and interference.
The clearance may vary depending on the specific DDR standard being used.
It is important to follow the recommended guidelines provided by the DDR manufacturer.
Failure to meet the minimum clearance requirements can result in signal integrity issues a...
Micro vias are small holes drilled in PCBs to connect different layers of the board.
Micro vias are typically less than 0.15mm in diameter.
They are used to save space on the board and increase routing density.
Micro vias can be drilled using lasers or mechanical drills.
They are commonly used in high-density interconnect (HDI) PCBs.
Micro vias can be filled with conductive or non-conductive materials.
They can be blind vias...
DDR signals include command, address, data, clock, and control signals.
DDR stands for Double Data Rate, which means data is transferred twice per clock cycle.
Command signals are used to initiate operations like read, write, and refresh.
Address signals specify the location of data in memory.
Data signals carry the actual data being transferred.
Clock signals synchronize the timing of all the signals.
Control signals includ...
The operating frequency of DDR4 is 2133 MHz to 4266 MHz.
DDR4 operates at higher frequencies than its predecessor DDR3
The operating frequency of DDR4 depends on the specific module and its configuration
DDR4 can operate at frequencies ranging from 2133 MHz to 4266 MHz
Higher frequency modules tend to be more expensive
Open drain is a type of output circuitry used in digital electronics. Open source refers to software that is freely available to use and modify.
Open drain is a type of output circuitry where the output transistor is connected to ground instead of a voltage source.
Open drain outputs are commonly used in digital circuits to interface with other devices or circuits.
Open source refers to software that is freely available t...
Fine pitch BGA refers to a Ball Grid Array (BGA) package with a small distance between the center of one ball to the center of the next ball.
Fine pitch BGA has a pitch of less than 1.0 mm.
It is commonly used in high-density applications such as microprocessors, memory chips, and graphics processors.
Fine pitch BGA requires precise manufacturing techniques and careful handling during assembly and rework.
Examples of fine ...
We used PCIe Gen3 x16 connector in our project.
PCIe Gen3 x16 connector provides high-speed data transfer.
It has 16 lanes for data transmission.
It is commonly used in high-performance graphics cards and storage devices.
It has a maximum bandwidth of 32 GB/s.
Examples of devices that use PCIe Gen3 x16 connector are NVIDIA GeForce GTX 1080 Ti and Samsung 970 PRO SSD.
I applied via Campus Placement and was interviewed before Oct 2022. There were 2 interview rounds.
Written test on basics of all subjects technical
Name mangling is a technique used by compilers to give unique names to functions and variables to avoid naming conflicts.
Name mangling is used in C++ to support function overloading.
It is also used in Python to avoid naming conflicts in modules.
Name mangling can make it difficult to access variables and functions from outside the class in which they are defined.
In C++, name mangling can be seen by using the 'nm' comman
I applied via Naukri.com and was interviewed in Aug 2020. There were 3 interview rounds.
I applied via Naukri.com and was interviewed before Jul 2020. There was 1 interview round.
I applied via Recruitment Consultant and was interviewed in Mar 2021. There were 3 interview rounds.
based on 7 reviews
Rating in categories
Hardware Design Engineer
23
salaries
| ₹0 L/yr - ₹0 L/yr |
HR Executive
12
salaries
| ₹0 L/yr - ₹0 L/yr |
RTL Design Engineer
12
salaries
| ₹0 L/yr - ₹0 L/yr |
Mechanical Engg. Design
10
salaries
| ₹0 L/yr - ₹0 L/yr |
Technical Writer
10
salaries
| ₹0 L/yr - ₹0 L/yr |
TCS
Infosys
Wipro
HCLTech