Filter interviews by
I applied via Walk-in and was interviewed in May 2022. There were 2 interview rounds.
I applied via Referral and was interviewed before Sep 2020. There were 3 interview rounds.
Flying mode in drive refers to the ability of a drive to operate without a physical connection to the motor.
Flying mode allows the drive to operate without a physical connection to the motor
It is useful for testing and commissioning purposes
Flying mode can also be used for emergency situations where the motor needs to be stopped immediately
During flying mode, the drive generates a simulated output signal to the motor
Fl...
I applied via Naukri.com and was interviewed in Mar 2024. There were 3 interview rounds.
Transformers, motors, generators, and electric generation are essential components in electrical systems.
Transformers are devices that transfer electrical energy between two or more circuits through electromagnetic induction.
Motors convert electrical energy into mechanical energy to drive machinery.
Generators convert mechanical energy into electrical energy.
Electric generation involves the process of producing electric...
DC motors are electric motors that operate using direct current (DC) power sources.
DC motors convert electrical energy into mechanical energy through the interaction of magnetic fields.
They are commonly used in appliances, power tools, and electric vehicles.
DC motors have two main types: brushed DC motors and brushless DC motors.
Brushed DC motors use brushes to conduct current, while brushless DC motors use electronic ...
Number System, coding and decoding, Analogies
Nodal analysis is a method used in electrical engineering to determine the voltage at each node in a circuit.
Nodal analysis involves writing Kirchhoff's Current Law equations for each node in a circuit.
It is used to analyze complex circuits with multiple nodes and voltage sources.
The goal of nodal analysis is to determine the voltage at each node relative to a reference point, usually ground.
It is a powerful tool for s...
A transformer is an electrical device that transfers electrical energy between two or more circuits through electromagnetic induction.
Consists of two coils of wire, known as primary and secondary coils
Primary coil receives electrical energy and creates a magnetic field
Magnetic field induces a voltage in the secondary coil, transferring energy
Used to step up or step down voltage levels in power distribution systems
Commo...
posted on 19 Mar 2025
I appeared for an interview before Mar 2024, where I was asked the following questions.
H-DOL feeders control connections manage motor operations and protection in electrical systems.
H-DOL (Direct-On-Line) starters connect motors directly to the power supply.
Control connections include start, stop, and overload protection circuits.
Example: A push button initiates the start sequence, engaging the motor.
Overload relays protect against excessive current, disconnecting the motor if needed.
Control circuits can...
Effective manpower management involves planning, organizing, and leading a team to achieve project goals efficiently.
Assess skills: Evaluate team members' strengths and weaknesses to assign tasks effectively. For example, assign complex tasks to experienced electricians.
Set clear goals: Define project objectives and communicate them to the team to ensure everyone is aligned. For instance, set deadlines for each phase o...
posted on 1 Feb 2025
I appeared for an interview before Feb 2024.
A Variable Frequency Drive (VFD) controls the speed of an AC motor by varying the frequency and voltage of the power supplied to the motor.
VFD converts fixed frequency AC power to variable frequency AC power.
It adjusts the motor speed by changing the frequency of the electrical input.
VFDs can be programmed to control acceleration, deceleration, and speed of the motor.
They are commonly used in HVAC systems, pumps, conve
A transmitter is a device that converts electrical signals into radio waves for communication purposes.
Transmitter receives electrical signals from a source
It modulates the signals to encode information
The modulated signals are then amplified and transmitted through an antenna
Examples include radio transmitters, cell phone transmitters, and Wi-Fi transmitters
ID fan is used to draw flue gases from the furnace while FD fan is used to supply combustion air to the furnace.
ID fan is located at the outlet of the boiler, while FD fan is located at the inlet of the boiler.
ID fan helps in maintaining a negative pressure inside the furnace, while FD fan helps in maintaining a positive pressure inside the furnace.
ID fan handles hot flue gases, while FD fan handles ambient air.
Example...
I applied via Naukri.com and was interviewed before May 2021. There were 2 interview rounds.
Composite error and ratio error are two types of errors in current transformers.
Composite error is the combination of ratio error and phase angle error in a current transformer.
Ratio error is the difference between the actual turns ratio and the specified turns ratio of a current transformer.
Phase angle error is the angular difference between the primary and secondary currents of a current transformer.
Composite error a...
An AC drive circuit diagram controls the speed of an AC motor by varying the frequency and voltage of the power supplied to it.
An AC drive consists of a rectifier, DC link, inverter, and control circuitry.
The rectifier converts AC power to DC power, which is stored in the DC link.
The inverter converts the DC power back to AC power with variable frequency and voltage.
The control circuitry adjusts the frequency and volta...
A single line diagram of a distribution system is required with proper specifications.
The diagram should show the flow of power from the source to the load
It should include all components such as transformers, switchgear, and cables
The specifications should include voltage levels, power ratings, and protection devices
The diagram should follow standard symbols and conventions
Example: A 11 kV distribution system with a 5
Dewpoint test is done in transformer to check the moisture content in the insulation oil.
Moisture in insulation oil can cause breakdown of transformer insulation
Dewpoint test helps to determine the moisture content in the oil
It is a preventive maintenance measure to avoid transformer failure
The test involves cooling a mirror until dew forms on it, and measuring the temperature at which dew forms
Power transformers are used in transmission systems to step up or down voltage, while distribution transformers are used in distribution systems to step down voltage.
Power transformers are used in high voltage transmission systems to step up or down voltage for long distance transmission.
Distribution transformers are used in low voltage distribution systems to step down voltage for local distribution.
Power transformers...
Buchholz relay is used to protect transformers from faults by detecting gas and oil flow abnormalities.
Buchholz relay is installed in the pipe connecting the transformer tank and conservator tank.
It operates based on the principle that faults in the transformer generate gases and cause oil flow disturbances.
When gas or oil flow abnormalities occur, the relay trips and sends a signal to the control panel to isolate the ...
I applied via Naukri.com and was interviewed before May 2021. There was 1 interview round.
Proxy is an intermediary server that acts as a gateway between clients and servers. SMPS is a power supply unit that converts AC to DC. Encoder is a device that converts motion into digital signals. Star delta is a method of starting three-phase motors.
Proxy helps in hiding the identity of clients and servers.
SMPS is commonly used in computers and other electronic devices.
Encoders are used in robotics, automation, and ...
I applied via Campus Placement and was interviewed in Aug 2020. There were 4 interview rounds.
posted on 15 Jan 2022
I applied via Walk-in and was interviewed before Jan 2021. There was 1 interview round.
The number of pl, cl, and pf ESI available is unknown.
The exact number of pl, cl, and pf ESI available is not provided.
There is no available data to determine the number of pl, cl, and pf ESI.
Without specific information, it is impossible to answer the question.
based on 1 review
Rating in categories
Assistant Manager
224
salaries
| ₹5.4 L/yr - ₹15.5 L/yr |
Senior Engineer
128
salaries
| ₹3.8 L/yr - ₹9.5 L/yr |
Associate Manager
126
salaries
| ₹6 L/yr - ₹17.5 L/yr |
Engineer
81
salaries
| ₹2.8 L/yr - ₹8.5 L/yr |
Deputy Manager
58
salaries
| ₹7.8 L/yr - ₹21.7 L/yr |
Tata Steel
JSW Steel
Jindal Stainless
Jindal Saw