Filter interviews by
Clear (1)
I applied via Campus Placement and was interviewed in Aug 2022. There were 3 interview rounds.
Very easy question but time is not more.
1st Introduction.
2nd Project
3rd Favourite Subject
4th Technical Questions
5th General knowledge
6th Hr round
I am selected in 1st round ,so 2nd time Interview for Technical + Hr
Top trending discussions
posted on 25 Jul 2022
I applied via Campus Placement and was interviewed before Jul 2021. There were 2 interview rounds.
posted on 31 Aug 2022
I applied via Campus Placement and was interviewed before Aug 2021. There were 2 interview rounds.
Equipment design involves identifying user needs, creating prototypes, testing, and refining the design.
Identify user needs and requirements
Create prototypes and test them thoroughly
Refine the design based on feedback and testing
Consider safety, ergonomics, and usability
Use appropriate materials and manufacturing processes
Ensure compliance with relevant regulations and standards
A centrifugal pump is a mechanical device used to transport fluids by converting rotational kinetic energy to hydrodynamic energy.
Centrifugal pumps are commonly used in industries such as oil and gas, chemical, and water treatment.
They work by using an impeller to create a low-pressure area at the center of the pump, which draws in fluid and then expels it at high pressure through the outlet.
Pumps are used to transport...
NPSH stands for Net Positive Suction Head. It is a measure of the pressure available at the suction side of a pump to prevent cavitation.
NPSH is important in pump selection and operation.
It is the difference between the total suction head and the vapor pressure of the pumped fluid.
Insufficient NPSH can lead to cavitation, which can damage the pump and reduce its efficiency.
Different types of pumps have different NPSH r...
posted on 5 Feb 2022
Basic aptitude and technical questions.
posted on 5 Feb 2022
I applied via Campus Placement and was interviewed in Jan 2022. There were 2 interview rounds.
Basic aptitude and technical e
posted on 8 Jul 2021
posted on 16 Jun 2022
Reasoning
posted on 5 Nov 2024
I was interviewed in Oct 2024.
Heat of formation is the energy released or absorbed when one mole of a compound is formed from its elements in their standard states.
Heat of formation is also known as standard enthalpy of formation.
It is typically measured in units of kJ/mol.
Negative heat of formation indicates exothermic reaction, while positive heat of formation indicates endothermic reaction.
For example, the heat of formation of water (H2O) is -28
Heat of reaction is the amount of heat released or absorbed during a chemical reaction.
Heat of reaction can be exothermic (heat released) or endothermic (heat absorbed).
It is typically measured in units of joules or calories.
Examples include combustion reactions releasing heat and photosynthesis reactions absorbing heat.
posted on 19 Sep 2023
I applied via Campus Placement and was interviewed in Mar 2023. There were 3 interview rounds.
Transformer protection is essential to prevent damage and ensure reliable operation.
Types of protection include overcurrent, overvoltage, differential, and thermal protection.
Relays are used to detect faults and initiate protective actions.
Buchholz relay is used for detecting internal faults in oil-filled transformers.
Pressure relief devices are installed to prevent explosion in case of internal faults.
Regular maintena...
posted on 14 Dec 2019
I applied via Campus Placement and was interviewed in Jun 2019. There were 5 interview rounds.
Herbicide is a type of pesticide used to kill unwanted plants.
Herbicides are chemicals that are used to control or kill unwanted plants.
They are commonly used in agriculture to prevent weeds from competing with crops.
Some herbicides are selective, meaning they only target specific types of plants, while others are non-selective and will kill any plant they come into contact with.
Examples of herbicides include glyphosat...
PI Industries is a leading agrochemical company in India that manufactures and supplies a wide range of products.
Nominee Gold
Fame Granules
Fame Insecticide
Ankur
Fame 1% Dust
Fame 2.5% Dust
Fame 5% Dust
Fame 25% WG
Fame 40% SC
Fame 50% SP
Fame 80% WP
Fame 20% EC
Fame 75% WP
Fame 50% WG
Fame 20% WG
Fame 25% SC
Fame 10% EC
Fame 20% SP
Fame 40% WG
Fame 50% EC
Fame 60% WP
Fame 70% WP
Fame 80% WDG
Fame 90% WDG
Fame 95% TC
Fame 97% TC
Fame 98% TC
Fam
Bernoulli's theorem explains the relationship between fluid speed and pressure.
Bernoulli's theorem states that as the speed of a fluid increases, its pressure decreases.
It is important in industries such as aviation, where it is used to design wings and airfoils.
It is also used in the design of pipelines and pumps.
Limitations include the assumption of incompressible and non-viscous fluids, and the neglect of friction a...
Pump is used to transfer fluids from one place to another while compressor is used to compress gases.
Pump is used to move fluids like water, oil, etc. from one place to another.
Compressor is used to compress gases like air, refrigerant, etc.
Pumps are used in industries, households, and agriculture while compressors are used in refrigeration, air conditioning, and gas pipelines.
Pumps have a lower pressure ratio while co...
Closing a shutoff valve while the pump is running dry can cause damage to the pump and other components.
The pump will continue to run but without any fluid to circulate, causing it to overheat and potentially seize.
The lack of fluid can also cause damage to the impeller and other internal components.
The pressure in the system can also increase, leading to potential leaks or bursts in the pipeline.
It is important to ens...
Closing the shutoff valve while pumping in a centrifugal pump can cause damage to the pump and the piping system.
The pump will continue to generate pressure, leading to a buildup of pressure in the piping system.
This can cause the pump to overheat and potentially damage the impeller.
The piping system may also experience damage due to the increased pressure.
It is important to ensure that the shutoff valve is only closed...
Connecting pumps in series increases head while connecting in parallel increases flow rate.
Connecting pumps in series increases the total head of the system while connecting in parallel increases the total flow rate.
In series connection, the discharge remains the same while the head increases.
In parallel connection, the head remains the same while the discharge increases.
Series connection is used when high head is requ...
Dimensions of power, energy, force and acceleration.
Power is measured in watts (W) and is the rate at which work is done.
Energy is measured in joules (J) and is the capacity to do work.
Force is measured in newtons (N) and is the push or pull on an object.
Acceleration is measured in meters per second squared (m/s^2) and is the rate of change of velocity.
Valves are mechanical devices used to control the flow of fluids or gases.
Valves are used in various industries such as oil and gas, water treatment, and chemical processing.
They can be classified into different types such as gate valves, ball valves, and butterfly valves.
Valves can be operated manually or automatically using actuators.
They play a crucial role in maintaining the safety and efficiency of industrial proc...
Types of what? Please provide more context.
Please provide more context for the question.
Without context, it is impossible to provide a meaningful answer.
Types can refer to many different things, such as types of engineering, types of materials, types of software, etc.
based on 6 reviews
Rating in categories
Executive Production
326
salaries
| ₹0 L/yr - ₹0 L/yr |
Executive
222
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Executive
215
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
92
salaries
| ₹0 L/yr - ₹0 L/yr |
Executive Engineer
51
salaries
| ₹0 L/yr - ₹0 L/yr |
Atul
Navin Fluorine International
SRF
Aarti Industries