Coromandel International Graduate Engineer Interview Questions and Answers

Q1. What is Heat of formation
Ans. 
Heat of formation is the energy released or absorbed when one mole of a compound is formed from its elements in their standard states.
• Heat of formation is also known as standard enthalpy of formation.

• It is typically measured in units of kJ/mol.

• Negative heat of formation indicates exothermic reaction, while positive heat of formation indicates endothermic reaction.

• For example, the heat of formation of water (H2O) is -28
Answered by AI
Add your answer
Q2. What is heat of reaction
Ans. 
Heat of reaction is the amount of heat released or absorbed during a chemical reaction.
• Heat of reaction can be exothermic (heat released) or endothermic (heat absorbed).

• It is typically measured in units of joules or calories.

• Examples include combustion reactions releasing heat and photosynthesis reactions absorbing heat.
Answered by AI
Add your answer

Good performance & technical answer

Q1. What is Pump Whay required pump
Ans. 
Pump Whay is a required pump for a specific application.
• Pump Whay is likely a typo and should be corrected to 'Pump What'.

• The required pump depends on the specific application and its requirements.

• Examples of pump types include centrifugal pumps, diaphragm pumps, and gear pumps.
Answered by AI
Add your answer
Q2. What is sop & standard ruals
Ans. 
SOP stands for Standard Operating Procedure, which are established procedures to ensure consistency and quality in operations. Standard rules are guidelines that must be followed.
• SOPs are detailed step-by-step instructions on how to perform a specific task or operation.

• Standard rules are general guidelines or regulations that must be followed in a particular setting.

• SOPs help in maintaining consistency, quality, and ef...read more
Answered by AI
Add your answer

Basics technical and basic aptitude

Q1. Question about basics mass transfer and heat transfer, fluid mechanics
Add your answer

Q1. Basic hr question and aptitude question discussion with assistant vice president
Add your answer

Q1. What are the various types of pumps
Ans. 
Various types of pumps include centrifugal, positive displacement, axial flow, and jet pumps.
• Centrifugal pumps use a rotating impeller to create a flow of fluid.

• Positive displacement pumps move fluid by trapping a fixed amount and forcing it through the discharge port.

• Axial flow pumps move fluid parallel to the pump shaft.

• Jet pumps use a combination of pressure and suction to move fluid.

• Other types of pumps include gea
Answered by AI
Add your answer
Q2. What is the least count of varnier caliper
Ans. 
The least count of vernier caliper is the smallest measurement that can be read on the scale.
• The least count is determined by the number of divisions on the vernier scale and the main scale.

• It is usually 0.1 mm or 0.02 mm for metric vernier calipers and 0.001 inch for imperial vernier calipers.

• To determine the least count, subtract the value of one main scale division from the value of one vernier scale division.

• For ex...read more
Answered by AI
Add your answer
Q3. Why is micrometre scree gauge is used instead of varnier caliper
Ans. 
Micrometer screw gauge is used for higher precision measurements than vernier caliper.
• Micrometer screw gauge has a higher accuracy of measurement than vernier caliper.

• Micrometer screw gauge has a smaller least count than vernier caliper.

• Micrometer screw gauge is used for measuring thickness, diameter, and depth of objects with high precision.

• Vernier caliper is used for measuring length, width, and height of objects wit
Answered by AI
Add your answer
Q4. What kind of difficulties have you faced in your internship and how you have solved it
Ans. 
During my internship, I faced difficulties in adapting to new software tools and collaborating with team members.
• Adapting to new software tools: I had limited experience with certain software tools that were used in the internship. However, I took the initiative to learn them by attending online tutorials, seeking guidance from colleagues, and practicing on my own.

• Collaborating with team members: Initially, I found it ...read more
Answered by AI
Add your answer
Q5. What is the difference between blower and compressor
Ans. 
Blower is used to move air or gas while compressor is used to compress air or gas.
• Blower is used to create a high flow of air or gas at low pressure.

• Compressor is used to compress air or gas to a higher pressure.

• Blowers are used in HVAC systems, while compressors are used in refrigeration systems.

• Blowers are used in industrial applications to move large volumes of air or gas.

• Compressors are used in pneumatic tools like
Answered by AI
Add your answer
Q6. Related to intership questions
Add your answer
Q7. Types of mechanical joints and processes
Ans. 
Mechanical joints are used to connect two or more mechanical parts together. There are various types of joints and processes.
• Welding joints - fusion welding, resistance welding, friction welding

• Brazing joints - torch brazing, furnace brazing, induction brazing

• Soldering joints - soft soldering, hard soldering

• Mechanical joints - bolted joints, riveted joints, snap-fit joints

• Adhesive joints - structural adhesive, pressure...read more
Answered by AI
Add your answer

Q1. What are your salary expectations?
Ans. 
I would expect a competitive salary that reflects my qualifications and the responsibilities of the role.
• Research the average salary range for Graduate Engineer Trainees in your industry and location.

• Consider your level of experience, education, and any additional skills or certifications you bring to the role.

• Take into account the responsibilities and expectations outlined in the job description.

• Be prepared to negotia...read more
Answered by AI
Add your answer
Q2. What is your family background?
Ans. 
My family background is diverse and supportive.
• My parents are both professionals in different fields.

• I have two siblings, one older and one younger.

• We come from a middle-class background and value education.

• My family has always been supportive of my career choices.

• We have a close-knit extended family and often gather for celebrations.
Answered by AI
Add your answer
Q3. Share details of your previous job.
Ans. 
I worked as a Junior Engineer at XYZ Company.
• Assisted senior engineers in designing and implementing projects

• Conducted research and analysis to support engineering decisions

• Collaborated with cross-functional teams to ensure project success

• Prepared technical reports and documentation

• Participated in on-site inspections and troubleshooting
Answered by AI
Add your answer
Q4. Why are you looking for a change?
Ans. 
Seeking new opportunities for professional growth and development.
• Looking for a more challenging role

• Want to broaden my skill set

• Seeking better career prospects

• Interested in working with a different industry or technology

• Want to work in a more collaborative and innovative environment
Answered by AI
Add your answer
Q5. Tell me about yourself.
Ans. 
I am a recent graduate with a degree in engineering, seeking a position as a Graduate Engineer Trainee.
• Recent graduate with a degree in engineering

• Seeking a position as a Graduate Engineer Trainee

• Strong knowledge in [specific engineering field]

• Experience with [relevant software/tools]

• Completed internships at [company/organization]

• Excellent problem-solving and analytical skills
Answered by AI
Add your answer