CIE Automotive Maintenance Manager Interview Questions and Answers

Q1. Which bearing used in CNC spindle? And why ?
Ans. 
Angular contact ball bearings are commonly used in CNC spindles due to their ability to handle both radial and axial loads.
• Angular contact ball bearings are used in CNC spindles because they can handle both radial and axial loads efficiently.

• These bearings provide high rigidity and accuracy, which are crucial for CNC machining operations.

• The contact angle of angular contact ball bearings can be adjusted to optimize per...read more
Answered by AI
Add your answer
Q2. What is Backlash?and how to check it ?
Ans. 
Backlash is the amount of clearance or play between two mating components in a mechanical system.
• Backlash is commonly found in gear systems, where it can affect the accuracy and efficiency of the system.

• To check backlash, one can use a dial indicator to measure the amount of movement between the components when they change direction.

• Backlash can be adjusted by tightening or loosening the components to reduce the cleara...read more
Answered by AI
Add your answer
Q3. How many types of Hydraulic valve are there ? Diffenciate between pressure relief and pressure reducing valve.
Ans. 
There are various types of hydraulic valves, including pressure relief and pressure reducing valves.
• Types of hydraulic valves include directional control valves, flow control valves, pressure control valves, and check valves.

• Pressure relief valves are designed to limit the pressure within a hydraulic system by diverting excess fluid when the pressure reaches a certain level.

• Pressure reducing valves, on the other hand, ...read more
Answered by AI
Add your answer

Q1. What is the unit of resistance ?
Ans. 
The unit of resistance is Ohm (Ω).
• The unit of resistance is denoted by the symbol Ω (Ohm)

• Resistance is measured in Ohms

• Named after German physicist Georg Simon Ohm

• Commonly used in electrical circuits
Answered by AI
Add your answer
Q2. Define the ohm law
Ans. 
Ohm's Law states that the current flowing through a conductor is directly proportional to the voltage across it and inversely proportional to the resistance.
• Ohm's Law is represented by the formula V = IR, where V is voltage, I is current, and R is resistance.

• It helps in calculating the relationship between voltage, current, and resistance in an electrical circuit.

• It is named after the German physicist Georg Simon Ohm w
Answered by AI
Add your answer

Our discussion was on how to maintain electrical machines healthy .So we discussed and found many ideas .It was really nice discussion i had

Q1. What you do for making yourself confidential ?
Ans. 
I ensure confidentiality by following company policies, maintaining data security, and keeping sensitive information private.
• Adhering to company policies regarding confidentiality

• Using secure methods for storing and transmitting data

• Avoiding discussing sensitive information with unauthorized individuals
Answered by AI
Add your answer
Q2. Whats your strengths ?
Ans. 
My strengths include strong problem-solving skills, attention to detail, and ability to work well under pressure.
• Strong problem-solving skills

• Attention to detail

• Ability to work well under pressure
Answered by AI
Add your answer

Q1. What is voltage define it?
Ans. 
Voltage is the difference in electric potential between two points in a circuit, measured in volts.
• Voltage is the force that pushes electric current through a circuit

• It is measured in volts (V)

• Voltage is the potential difference between two points in a circuit

• Higher voltage means more energy available to move electrons

• Voltage can be DC (direct current) or AC (alternating current)
Answered by AI
Add your answer

Q1. 1.type and diffrance of encoders 2.MTBF&MTTR 3.Communication protocol plc
Ans. 
Encoders can be incremental or absolute, MTBF is Mean Time Between Failures, MTTR is Mean Time To Repair, common communication protocols for PLCs include Modbus and Profibus.
• Encoders can be incremental (provide relative position) or absolute (provide exact position)

• MTBF is the average time between failures of a system or component

• MTTR is the average time it takes to repair a failed system or component

• Common communicati...read more
Answered by AI
Add your answer
Q2. 4.Servo drive 5.vfd drive
Add your answer

Plc programming test

Q1. Fresher student for every field
Add your answer

Q1. Fresher student for every field
Add your answer

Q1. A few knowledge of ac and DC machine
Add your answer

Q1. Related to work and kpi
Add your answer
Q2. Why want to leave
Add your answer
Q3. Machine related conditional questions
Add your answer

Q1. Draw a circuit diagram to convert 230v ac to 24v dc.
Add your answer
Q2. PLC Ladder logic Diagram
Add your answer

Q1. As per your resume and experience
Add your answer
Q2. Tyre industries Prosses and its related
Add your answer
Q3. Basic knowledge of plc and scads system
Add your answer

Q1. What is the difference in A.C. D.C.
Ans. 
AC and DC are two types of electrical current. AC stands for alternating current and DC stands for direct current.
• AC is the type of current commonly used in homes and businesses, while DC is used in batteries and electronic devices.

• AC current periodically changes direction, while DC current flows in one direction.

• AC current can be easily converted to different voltages using transformers, while DC current requires a po...read more
Answered by AI
View 1 more answer
Q2. What are the types of wiring
Ans. 
There are several types of wiring used in electrical installations.
• Conduit wiring: Electrical wires are enclosed in metal or plastic conduits for protection.

• Surface wiring: Wires are mounted on the surface of walls or ceilings using clips or channels.

• Concealed wiring: Wires are hidden inside walls or ceilings, usually in conduit or trunking.

• Cleat wiring: Wires are supported by porcelain or plastic cleats fixed to walls...read more
Answered by AI
View 1 more answer